Search Documents

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

In spite of the many contributions that have been made to our knowledge of the creep properties of polycrystalline lead, the precise influence of various factors on these properties is not yet fully understood. Indeed, the position is such that several important points in connection with the creep of lead are a matter of controversy. This has been brought about largely by the fact that, in the case of lead, the changes that are produced in the creep behaviour by slight variations of such factors as the purity, grain sizeand previous treatment are out of all proportion to the magnitude of these variations.In order to study the fundamental properties of lead as related to creep, and so gain a more enlightened perspective with which to consider the creep of lead in general, the work that is described in a series of papers, of which the present paper is the third part, has been carried out. It deals with lead in the form of single crystals.It has been shown (1) - (3) that the grain boundaries as well as the actual grains play a part in the creep of polycrystalline lead. The present work, by eliminating grain boundaries, enables the. contribution of the grains themselves to the process of creep, in other words, crystalline creep, to be studied effectively.This object was, possibly, the major one in this work.

Jan 1, 1940

By T. T. Tomimatsu

This? Bureau of Mines paper discusses the corporate structure dynamics, methods of financing, and financial assessment approaches that should be utilized to evaluate the economic health of the coal industry. It suggests rates of return and other measures of corporate economies necessary to attract capital required to finance emerging coal demand, plus impact of coal sales to total revenues. The study illuminates the activities of 30 selected coal-producing companies, including their subsidiaries or affiliates, that were responsible for approximately 60 percent of the total U.S. production in 1974. The selected firms are not all primary coal producers; many of the larger producer's are classified by the financial institutions as petroleum, metal, and steel producers, public utilities, or chemical industries. The bituminous coal industry is highly competitive as to price, service, and quality of pronuct and is subject to competition from other noncoal energy sources. The top 15 bituminous coal-producing companies mined about 46.6 per-cent of the Nation's total production in 1974, and the balance of approximately 3,885 companies were responsible for the rest of the production. Thus, the U.S. bituminous coal industry is not an oligopoly. Today, about 65 percent of the Nation's total coal production is consumed by electric power utilities and 26 percent by steel, space heating, and other industries; the balance of 9 percent is exported.

Jan 1, 1976

By Mohan K. Wali

Soil and vegetation development were studied on abandoned mine sites near Velva in Ward County, North Dakota. The sites studied were 1, 7, 17, 30 and 45 years old since abandonment; unmined sites were also studied to provide measures of comparison. Species diversity was the highest at unmined sites (114) and lowest at the I year old site (26); sites 7, 17,30 and 45 years old had 37, 52, 43 and 68 species, respectively. Stand ordination revealed that site ages were the most important in influencing species diversity and composition. Stand-environ-mental complex ordinations encompassing 53 variables showed topographic variables to be the most important followed by site ages. Rates of nutrient accumulations were as follows: organic carbon 13.1 g m-2 yr-1; nitrogen 2.5 g m-2 yr-1; phosphorus 0.01 g m-2 yr-1; potassium 0.49 g m-2 yr-1. Carbon-nitrogen ratios showed the widest range for 1 year old sites (5-40) but 70 percent of the 45 year old sites showed values below 15 which were com-parable to the unmined mixed grass prairie sites. Species distributional diagrams are provided to show their habitat preferences which may be helpful in formulating species prescriptions for revegetation.

Jan 1, 1982

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By James P. Sloss

WHAT is the likelihood if any-that a real gold mining industry will be developed in the southern Appalachian region? Has the increase in the dollar value of gold from $20.67 to $35 per ounce potency to turn the trick? Suppose it be assumed that the price of gold will, at worst, not recede, and that the cost of digging ore and treating it of which the average level of commodity prices and wages is a fair index-will, at most, not exceed that prevailing in 1926. One may or may not accept these as reasonable assumptions; but one must arbitrarily remove some of the potential variables if one is to get anywhere on a problem like this. As a matter of fact, this article is not going to venture a conclusive answer to the question that has been posed; but it will endeavor to present some of the factors that have a bearing on the problem. The writer spent ten days visiting a dozen properties in Virginia and the Carolinas early in April, 1935, and in doing so got a first-hand slant on mining conditions in the domain of King Cotton.

Jan 1, 1935

THE method depends upon:--1. The position of the mill.2. The space available for stacking the residue.3. The nature of the residue as discharged from the mill.4. The value of the residue for re-treatment.5. The requirement of the residue for underground filling.Originally the conditions in this district varied mainly in the position of the mill, some mills having an elevated site with plenty of dumping space for the time being, whilst others had a flat site, and very little dumping space near at hand; but in most cases the residue discharged was in the form of filter-press cakes, suitable for conveying on belts, or in trucks, and stacking in a high clump; and, while a portion of the residue was used for underground filling, the dump was regarded as a valuable asset, to be re-treated later. Under these conditions, conveyor belts, electric trams, aerial trams, and hose trucks, all gave satisfactory results, and the following figures, taken from "'West Australian Metallurgical Practice," will show how these methods compared as regards costs...

Jan 1, 1909

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

Allis Mineral Systems ARCO Coal Company Buckley Powder Co. CALCO, Inc. Coal Magazine Colowyo Coal Company Continental Conveyor & Equipment Company Crane & Hoist Sales Cummins Southwest, Inc. Energy West Mining Company Paul J. Epley FMC Corporation The Falkirk Mining Company Fleischli Oil Co., Inc. T. J. Gundlach Machine Company Halbach & Braun Harnischfeger Corporation Hemscheidt Corporation Hyatt Regency Beaver Creek Jennmar Corporation Joy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Coal Company Phillips Machine Service, Inc. Pincock, Allen & Holt, Inc. Pittsburg & Midway Coal Mining Co. Roberts & Schaefer Company Rust Tractor Company Salt River Project Santa Fe Pacific Coal Corporation Schroeder Industries Shearson-Lehman Brothers Southern Pacific Transportation Stamler Corporation Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1992

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006