Search Documents

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Boone County, W. Va., as determined by the Bureau of Mines. It is one of a series describing the coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 6.3 million tons of coal was produced in Boone County, W. Va., in 1959, of which almost 5.5 million tons was mechanically cleaned in eight preparation plants. On December 31, 1959, it was estimated that almost 8 billion tons of coal remained in the county in beds 24 inches or more in thickness. Thirteen samples were collected from nine coalbeds and washability tests were made on these samples.

Jan 1, 1961

By John E. Kinnison

The Mission mine, located in southern Arizona near Tucson, is a recently developed open pit which produces 15,000 tons per day of copper ore. The mine lies on a wide and gently sloping bajada sweeping northeasterly from the Sierrita mountains. It derives its name from the nearby Mission San Xavier del Bac, built circa 1700. The ore body is everywhere covered by about 200 feet of alluvium, as are the adjacent Pima and Palo Verde mines. The geology of the Mission deposit is known principally through the study of diamond drill holes spaced 150 to 300 feet apart. The open pit is in an infant stage and has not yet revealed much of the deposit, although information obtained there by the operating staff, and from a few thousand feet of exploratory underground workings, has added significantly to the general fund of knowledge. Permission to publish was granted by the American Smelting and Refining Company. I am indebted to Kenyon Richard and J. H. Courtright for criticism of this paper and for their direction during the several years in which I studied the Mission deposit. Acknowledgment is given to consultant in petrography, Robert L. DuBois of the University of Arizona. The only previous publication pertaining directly to the geology of file Mission deposit appeared in 1959 (Richard and Courtright), and may not be everywhere readily available. Cooper (1960) has published a short paper on the district

Jan 1, 1963

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996

By J. S. Pascover, J. K. Abraham

The influence of the early stages of precipitation on the kinetics and structure of martensite formation in Fe-27Ni and Fe-29.5Ni alloys containing from 0 to 10 pct Ti was examined with X-ray and electron microscopy techniques. The formation of a coherent, ordered preprecipitate had a profound stabilizing effect on the austenite. The Ms was decreased by increased titanium content and aging time up to a critical time. When the critical aging time was exceeded, the Ms was observed to increase markedly. The formation of the clusters was insuppressible and the volume fraction of clusters formed during the quench was a function of the titanium content. Martensite resulting from transformation of the clustered austenite is tetragonal with the c/a ratio increasing with titanium content. A model for the tetragonality is suggested. The morphology and substructure of the m artensite is inter-preted in terms of the above information and the cur-rent models of twinned martensite. ThE ramifications of precipitation in austenite to the properties of austenite have been the subject of numerous investigations. The current research is concerned with the influence of precipitation in austenite on the kinetics and structure of subsequent marten-site formation. In a previous investigation, Abraham et al.1 followed the aging reaction in an Fe-29.5Ni-4.2Ti* (at. pct) alloy using an X-ray diffraction technique. This technique, employing a Guinier camera, provided kinetic measurements through observation of the side band position as a function of aging time. The salient results of this work were: 1) The initiation of precipitation was not suppressed by quenching, i.e., there was a finite cluster zone size at zero aging time; and 2) The hardness of the aged austenite correlated extremely well with the zone size. During the previous work it was noted that the mar-tensite formed after aging was tetragonal, substanti-ating an earlier observation.2 Systematic investiga-tion revealed that the martensite was tetragonal in both the solution-treated then quenched, and the solu-tion-treated, aged, and quenched condition, and, furthermore, that a marked stabilization of the austenite occurred as a function of aging time. The present work is concerned with documenting the tetragonality and the stabilization phenomena as well as the ob- served microstruction with a suggested rationale for the behavior noted. EXPERIMENTAL PROCEDURE The compositions of the alloys are listed in Table I. The analyses were performed after the solution treatment of the strip material. Nickel was determined using the standard dimethy1-glyoxime procedure whereas titanium was determined colorimetrically with hydrogen peroxide and volumetrically by titrating with ferric iron. The materials were melted in a 5-lb vacuum induction furnace, cast into 2-in.-diam ingots, and forged in a temperature range of 950. to 1200°C to 1/2-in. slabs. The three higher titanium containing materials cracked during forging; therefore, to get the alloys into strip form, slices 1/8 in. thick were cut from the slab, homogenized 4 hr at 1150°C, then cold-rolled to a 0.04-in. thickness. The remaining slabs were hot-rolled, homogenized 4 hr at 1065"C, then cold-rolled to a final thickness of 0.03 in. All of the heat treatments were performed under a protective atmosphere of argon. The Ms temperature for most of the alloys is below room temperature; therefore, it was possible to solution treat, quench to room temperature, polish, and then observe the transformation optically on a cold-stage microscope. To determine the effect of aus-tenitizing temperature on Ms, eight of the alloys were treated at two temperatures, 1025" and 1120°C. No measurable variations in Ms were noticed. The remaining alloys were treated at 1025°C. The specimens, : by 5/16 by 0.03 in., were austeni-tized in a vertical tube furnace under a dynamic argon atmosphere. The bottom of the tube was submerged in water for quenching purposes. The question of stabilization that may be operating at room temperature was investigated and found to be negligible. Many of the specimens were held at room

Jan 1, 1970

By G. S. Tint, M. Herman, V. V. Damiano

Dislocation arrays and substructures were studied in cadmium doped zinc crystals using a newly devised etching technique. Cadmium precipitates delineating the dislocations were revealed by etching a surface closely parallel to the (0001) slip plane. Cinephotomicrography of the continuous etching process revealed the three-dimensional aspects of dislocations in the bulk crystal. Dislocation etch patterns were studied in both deformed and annealed crystals after suitable aging at room temperature. The effect of annealing was evidenced by a rearrangement of the dislocations into low-angle boundaries and hexagonal networks. ETCH pit techniques have been used extensively to study dislocations in both deformed and annealed bulk metal crystals. Ideally one hopes to obtain a one-to-one correspondence between the etch pits and the points of emergence of the dislocations at the surface. One then attempts to deduce the way in which dislocations are arranged in the bulk crystal from the arrangement of etch pits on the surface. It is clear that one can obtain only limited information of the dislocation configurations inside the crystal from etch pit studies of single surfaces. Considerably more information is obtained if one is able to follow the course of the dislocations through the crystal using progressive etching technique. Techniques of this sort were used by Gilmanl to study dislocations on the slip planes of NaCl crystals and by Damiano and Tint2 to study dislocation arrangement in zinc crystals grown from the melt. The present paper makes use of a technique first described by Tint and Damiano3 to observe and continuously record the dislocation structures which appear while a crystal surface was being progressively etched. Studies were made on cleaved (0001) surfaces to reveal the dislocations along their length on the surface closely parallel to the slip plane. The technique for revealing segments of dislocations along their length by etching is well known. Wilsdorf and Kuhlmann-wilsdorf4 revealed disloca- tions along their length in aluminum containing a few percent copper, when precipitates segregated along the dislocations. The technique was used by Low and Guard5 to study dislocation configurations on the slip plane in Fe-Si alloys containing carbon. In the present work the technique was applied to zinc containing cadmium since it was shown by Gil-man6 that a cadmium-rich phase could be made to precipitate from supersaturated solutions along dislocations in zinc. Segments of dislocations delineated by the precipitates were revealed by etching a surface prepared by cleaving the crystal. The three-dimensional nature of dislocations and substructures was thus studied from the cinephotomicro-graphic record of the continuous etching process. EXPERIMENTAL Single crystals of zinc containing the order of 0.1 pct Cd were prepared by slowly lowering a graphite crucible containing the melt through a temperature gradient of 15°C per cm at a rate of 1.5 X 10-3 cm per sec. "As grown" crystals were aged for periods of 1 month at room temperature, then cleaved in liquid nitrogen, and etched according to the procedure used by Gilman.&apos; The etchant containing 32 g of CrO3, 6 g of hydrated Na2SO3 in 100 ml of water behaved as a chemical polish for zinc and etch pits were produced at the site of precipitates or inclusions. After the precipitates or inclusions were removed from the surface, the etch pits left behind were eventually polished smooth. This behavior enabled one to continuously observe the surface while the specimen was immersed in the etchant. Best results were obtained when the specimen surface was vertical and the reaction products of polishing were continuously removed by gravitational convection. Some crystals were heavily deformed in excess of 25 pct strain, others were lightly deformed the order of a few pct by compression such that the deformation occurred essentially by basal glide. Some crystals were etched immediately after deformation, others were allowed to age at room temperature for several weeks prior to etching. Heavily deformed crystals were annealed at various temperatures and etched on the cleavage plane immediately after annealing, others were allowed to age at room temperature for several weeks prior to etching. The etched structures of deformed and annealed structures were studied. Similar experiments were conducted on 99.9999 pct pure zone refined Tadanac zinc crystals which

Jan 1, 1963

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The tactual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the twelfth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate halt-township map. The description of each half township is followed by a description of each deposit developed in that halt township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By George W. Toth

In a recently completed research project for the U.S. Bureau of Mines - Twin Cities Research Center, a computerized costing procedure for uranium in situ leach mining was developed by the NUS Corporation. This costing procedure, termed a cost model, employs a process engineering approach for estimating total project costs as well as equipment and manpower requirements for uranium in situ leaching operations in either Texas or Wyoming. 80th capital and operating costs are generated by the model along with the overall production cost/pound U3O8 subject to a known rate of return. Conversely, rate of return on equity can be solved for, subject to a given price of yellowcake. During the course of the research effort, this cost model was applied 50 typical site conditions in Texas and Wyoming. Sensitivity rests were conducted for numerous key parameters to determine the cost influence attributable to incremental changes In parameter values. The results of these sensitivity tests along with a description of the in situ leaching cost model have been documented as Bureau of Mines, Mineral Research Contract Report No. J019912, "Cost and Sensitivities Analysis for Uranium In Situ Leach Mining," dated March 1981.

Jan 1, 1981

By Barry W. Klein

The U.S. economy was considerably stronger in 1976 than in 1974 or 1975. Real gross national product (GNP) rose sharply in the first quarter of 1976 and then increased at a more moderate rate for the remainder of the year. The unemployment rate fell until June and then increased for moat of the remainder of the year, finishing at the same rate as it had started the year. The inflation rate continued to decline in 1976. Reasons for the relatively low rate (compared with those of 1974 and 1975) included small increases in food prices and only moderate increases in energy prices. Total U.S. output measured in terms of GNP increased 11.6% in 1976. Real GNP in 1972 constant dollars rose 6.2%. Inflation as measured by the implicit price deflator increased 5.1%. In real terms, gross private domestic investment for residential structures rose 22.7% in 1976 after declining 14.7%a in 1975; State and local Government expenditures increased 1.4% in 1976; and personal consumption expenditures for services rose 4.5%. The Federal Reserve Board (FRB) index of industrial production increased 10.2%.

Jan 1, 1978

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By J. L. Fuller

Thousands of mine air samples are taken underground each year by MSHA inspection personnel in order to further assure that miners have a safe and healthy environment in which to work. While most air samples are taken with stain tubes, many samples are obtained in evacuated containers and returned to a laboratory for more accurate analysis on a gas chromatograph. In order to enhance the accuracy, reliability and repeatability of the samples taken with evacuated containers, improved procedures have been developed, which are described in this report, for filling two different types of evacuated sample containers using either mechanical or electrical pumps. In those instances, such as when sampling strata gases in drill holes, where mathematical calculations may be required for proper sampling, example calculations are provided. The use of a third type of evacuated container, which is generally restricted to non-specific sampling of the ambient mine atmosphere, is also described.

Jan 1, 1986

By H. M. Friede

Iron Age metal working in the Magaliesberg area by H. M. FRIEDE, Ph.D. (Visitor) Evidence of smelting and metal working in the Magaliesberg comes mainly from three sites: Broederstroom (Pretoria District). Uitkomst Cave (Krugersdorp District), and Olifantspoort/Olifantshoek \Rustenburg District). The analyses of copper ores found at or near these sites are reported. as are the analyses of twenty-six samples of slag from the Magaliesberg area and other sites in the Transvaal. Iron implements and copper ornaments found at the Magaliesberg sites are described. and the analyses of some of these specimens are reported and discussed. A metallographic report on two iron objects from Broederstroom points to similarities in the smelting and forging techniques that were practised in the Transvaal and Nigeria during the Early Iron Age.

Jan 6, 1977

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By Mark J. Dowiak, Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980s. About 45 Mt of hazardous wastes are produced yearly. One major aspect of the problem is the siting, design, and construction of&apos; environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sites for several reasons. • Surface mines offer an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic, savings when compared with sites on undisturbed lands that might require extensive excavation or embankment construction. • Surface mines often have an abundance of mine spoil available that could potentially serve as construction material. This could result in a significant economic advantage over other sites that might require extensive amounts of construction material to be excavated or hauled in. • Operation of a commercial disposal facility in a surface mine can reduce or totally alleviate reclamation costs. • For an abandoned surface mine, conversion into a disposal facility could represent a positive form of land use and may provide a means for reclaiming lands that would otherwise remain unreclaimed. Despite these positive reasons, there are many technical factors associated with surface raining that can make the prospect of disposal site development an uncertain one. Before discussing factors associated with mining that can present siting, design, or construction problems, some understanding of the basic components of a chemical waste disposal facility is necessary.

Jan 2, 1981

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985