Search Documents

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By D Matthews

With a brownfield project comes control integration challenges. The Khumani Iron Ore Mine’s second phase expansion posed a number of challenges as there was substantial brownfields work conducted. The fi rst phase was the compilation of the modifi ed process functional specifications for the project. The second phase was an audit on all of the operational sequences; this included a comparison between the SCADA sequences, sequential starts analysed from the historian data (with the potential for improvements made by the plant operators in manual start-ups) and what was proposed in the process functional specification. Differences, inclusions and missing equipment were highlighted. The third phase was the comparison of interlocking and control in the PLC with the updated process functional specification; this was done during the coding process. Running parallel to the three phases was the SCADA integration; tie-ins to the existing SCADA were conducted on maintenance days and shutdowns, in many instances with ‘dummy’ equipment to get the operational staff accustomed to the new interface. This paper details each of the phases, the success of this methodology as well as the pitfalls experienced.

Jul 11, 2011

By Brian W. Mackenzie

The paper addresses five questions concerning the economic of gold exploration in the western Canadian shield. Can historical footprints be used to project future gold prices for exploration planning? Experience suggests that gold price forecast are too clo ely tied to current market events to provide meaningful guidelines. What range of breakeven gold price will typically be required to ju tify gold exploration in Canada? Minimum price requirements. initially asses ed at $540 to $1080 per ounce, probably lie in the range of $480 to $760 per ounce (expressed in 1985 Canadian dollar). Within Canada, what role do regional conditions and taxation policies play in determining the viability of prospective gold exploration targets? Striking interprovincial differences are found to exist, given the same geological circum tance -Nova Scotia, ew Brunswick, and Quebec rank towards the top in term of motivating exploration, Briti h Columbia provides the least investment incentive, while Saskatchewan and Manitoba place around the middle of the Canadian league. How can minimum acceptable tonnage-grade conditions for gold targets in the western shield be established and, then, constructively applied to provide exploration planning guidelines? Minimum target conditions, realis tically defined in terms of a broad band of doubt, can be used judiciously to help balance the direct costs of uneconomic exploration with the opportunity costs associated with rejecting economic deposits. How does the average cost per ounce of gold discovered in the western shield compare with the overall Canadian experience? Average discovery costs for the we tern shield, apprai ed at $100 per ounce, are shown to compare favourably with the Canada-wide record.

Jan 1, 1986

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to determine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

By B Nielsen, H Lehto, J Rohleder, C Robben

Sensor-based ore sorting is being increasingly used to reduce the amount of low-grade and waste material processed in mineral concentrators. This type of preconcentration provides bottom-line benefits to users by reducing the amount of energy, water and consumables, as well as reducing capital cost. Existing operations can increase metal production, while previously uneconomic deposits and low-grade stockpiles can also be exploited. The technology can also be used to separate ore types for selective processing. The path to implementing sensor-based sorting may include:• geometallurgical evaluation• first inspection testing to investigate sensor response• bench-scale testing where sensor selection is not obvious or for difficult applications• performance testing in full scale sensor-based sorting machines• larger scale site-based piloting with a temporary semi-mobile plant installation. Sorting requires material to be suitably prepared and presented to the machines and typically this consists of crushing and screening to limit top size and optimise liberation. However, where material streams are suitably sized and prepared, additional equipment may not be required (e.g. the sorting of semi-autogenous grinding (SAG) Mill pebble streams).This paper presents a case study of economic upgrading of gold ore, by preconcentrating with sensor-based ore sorting. The case study examines sorting amenability, test work, the feasibility study through to implementation, with associated flow sheet development. The development process is analysed and evaluated with a view to rationalising the process for development of future projects. In addition, limited financial modelling based on expected results is shown to illustrate the benefit to the operation.CITATION:Nielsen, B, Rohleder, J, Lehto, H and Robben, C, 2017. Sensor-based ore sorting to maximise profit in a gold operation, in Proceedings MetPlant 2017, pp 131–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By C. H. Riggs

This petroleum-engineering study of the Healdton oil field in Carter County, Okla., describes the geology and production history of that field and estimates the oil reserves that could be produced by efficient secondary-recovery methods. The Healdton field, in western Carter County approximately 20 miles west of Ardmore, Okla., was discovered in 1913 and was one of the early important oil-producing areas in the State. Although the volume of oil recovered from the Healdton sands has been comparatively high, studies show that a large reserve remains in the pressure-depleted sand, which can be recovered by efficient water-flood operations. In making this study of the Healdton-sand reservoir, the writers utilized many data already available in company and Government offices. Most of the fluid samples were collected by Bureau of Mines personnel and analyzed in the Bureau's laboratories at Bartlesville, Okla.; but other data, including logs, core analyses, and production records, were obtained from outside sources. These data were examined critically but were not verified, and possible errors in the original data may be reflected in the conclusions. In this study, attempts were made to consider only those aspects of the available information that would contribute to a clear and concise engineering report on the Healdton-sand reservoir. Other phases of the data, as well as those concerning associated reservoirs, were eliminated from consideration as being irrelevant to the particular problem. Cores and drill cuttings of the Healdton sands were analyzed and studied to determine the nature of the reservoir rocks. Analyses of samples of produced oil, water, and gas were studied to fix the different types, the limits of their occurrence, and the suitability of different waters for injection into the Healdton sands. Records of oil, gas, and water produced and of gas and water injected were studied to interpret the production behavior of the field and of certain individual leases. Theoretical calculations were made to predict the probable water-flood behavior and oil recovery, at constant water-injection rates, for individual sands on two leases.

Jan 1, 1953

By Harvey T. Gracely, Mark J. Woodhull

DURING the past few years a marked refinement has taken place in the design of electric power shovels for the mining industry, increasing their digging ability and speed of operation without adding to their total weight. The increase in pay load has been accomplished by a more rigid engineering analysis of shovel design, involving the adoption of new special alloy steels, new sections, and new welding methods. Emphasis has been placed on lightness with increased strength, which is most clearly shown in the front-end equipment where dipper, handle and boom are new in design, material, and construction.

Jan 1, 1938

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to deter- mine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.'s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By JOHN W. KOSTER, JAMES R. FLEMING

The following report is made through the Bureau of Mines as a result of the work under the cooperative agreement with the State geological survey and the engineering experiment station of the University of Illinois. It deals with the use of permissible explosives in the coal mines of Illinois, and is intended primarily to present to mining men the possibility of assuring safer conditions in mining through the use of these explosives. Twenty coal mines in Illinois were using these relatively safe explosives at the time this report was prepared. Of these, seventeen were in Franklin County, two were in Saline County, and one in Montgomery County. In these various fields experience had shown that although black blasting powder was a useful agent in breaking down the coal at the working face, yet it had given such conclusive evidence of its danger to life and property in causing explosions and mine fires that a substitute was sought and has been found in permissible explosives. Each coal mine in Illinois in which permissible explosives are used was visited and a study made of the problems involved. The report deals briefly with the dangers of black blasting powder now in such common use in coal mining. It discusses the development of permissible explosives and their introduction into Illinois coal mines and points out the characteristic differences between permissible explosives and black blasting powder. The present system of blasting and the most approved methods of using permissible explosives are described. Data are given to show that not only has safety and efficiency in these mines been greatly improved, but that the cost of explosives to the miner per ton of coal has been reduced, and that sizes of coal produced from permissible explosives compare favorably with those previously obtained at the same mines with black blasting powder. The successful use of permissible explosives in these Illinois mines as well as in many other mines throughout the country should aid in their introduction into a larger number of mines and bring about that degree of freedom from explosions and fires which should be attained in mining.

Jan 1, 1917

This modern plant was installed with the object of treating all oxide ore and payable dump material by the cyanide process.The plant is located on a ridge on the eastern side of Linda Gully. The mill -site has a slope to the south of 1 in 4.The new plant is of steel and concrete construction and was specially designed to suit the climatic conditions which exist at Mount Morgan.THE COARSE CRUSHING PLANTThe ore received from the, mine is dumped into a 600-ton steel bin which is commanded by a 3 ft. 6 in. gauge railway,The mine ore is conveyed by steam locomotives in rakes of five self-dumping 7-ton railroad cars. The dump material is mostly loaded by bull-dozers and conveyed to the binsin large motor lorries. Located on the top of the bin is a heavy railroad grizzly having 12-in openings through which all ore must pass.The flow of ore from this steel bin is controlled by a No. 7D 3-speed Ross chain feeder. It should be mentioned here that, although the bottom of the steel bin is inclined at an angle of 45°, it has been found, owing to the clayey nature of the oxide ore, that the live capacity of the bin is only about 50% of the total capacity.

Jan 1, 1939

By Wilson Bardales

El presente trabajo describe la experiencia de la Gestión de la Calidad en la Cía. Minera Poderosa S.A., específicamente en el rol que desempeñan los Círculos de Mejoramiento Continuo (CMC´s) como un vehículo efectivo para alcanzar los objetivos de la empresa. Los CMC´s están integrados por trabajadores de un mismo proceso, a quienes se capacita en el manejo de herramientas, técnicas y metodologías de la calidad, con la finalidad de realizar mejoras en los procesos. En ese sentido, en la compañía minera La Poderosa, la administración es participativa y el directorio difunde las políticas, para lograr la rentabilidad de la empresa. Así también, los mandos medios definen los objetivos y estrategias, desplegándola en cascada a la supervisión y estos a su vez, al personal de línea. Este concatenamiento de responsabilidades y la participación de los CMC´s aseguran el alineamiento y control de la gestión.

Sep 12, 2005

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003