Search Documents

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By T. Fraszczak, U. A. Peuker, T. Mütze, O. Ortlepp

Dolomite is a calcium carbonate sedimentary rock that can be found all over the world. In its calcined form it is employed for water treatment or as an additive in iron production. Calcined dolomite is produced at the Wünschendorfer Dolomitwerk GmbH in shaft furnaces (kilns). Because of an expansion of the mined deposit, significantly higher extraction costs were expected. Therefore, the existing upgrading processes for the kiln stone fraction had to be adapted and improved. This paper presents a process optimisation which allows for an increase of the yield of calcined dolomite by 10 % due to a redesign of the crusher circuit and by an additional 5 % due to a comprehensive characterisation of the kiln stone fraction itself. Here the interdependency between the pressure drop in the furnace during calcination and the size distribution of furnace stones was used to increase the amount of fine size fractions in the furnace feed without deterioration of the calcination process. Keywords: Dolomite, crushing circuits, kiln stone production, flowability, calcination

Jan 1, 2020

By Werner Joseph

El presente trabajo describe los aspectos que comprenden la metalurgia del antimonio y sus compuestos. Para ello, se revisa su historia, propiedades físicas y químicas, origen y materias primas, pirometalurgia de los minerales sulfurados y oxidados, hidrometalurgia y electrometalurgia, métodos extractivos especiales, producción de los principales compuestos, mercado y proyecciones futuras.

Mar 1, 1985

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By Shiou-Chuan Sun

The froth flotation of coal, differing greatly from that of most minerals1-5, is not improved but rather impaired by temperatures higher than room temperature6-10 This phenomenon has long taunted us for an explanation. Gayle and Associates 8,9 reported the lack of relationship between their contact angle measurements and their flotation of American coals under various temperatures. Bailey and Whelan6 stated that the viscosity of flotation reagents, offering some clue for their flotation of British coals at low temperatures, could not be put forward as an explanation either in whole or in part for the effect of temperatures on coal-flotation. In this paper, a froth hypothesis is proposed to explain the flotation behavior of coals under various pulp temperatures. Test work involved the flotation of coals and the frothing of reagents.

Jan 1, 1966

By John Mills

THREE case histories from professions other than engineering will serve to introduce ideas basic to this discussion. Case (1) Date, about 1900. A young man, B. D. from a three-year graduate course in a prominent divinity school, was for two years a successful pastor of a small church; then friction over theological matters arose with a fundamentalist deacon of the "Bible belt" type. He resigned, returned to his university for a four-year medical course, interned for two more, and thereafter was successful and apparently happy as a physician. We may assume that he was converted in early adolescence and vowed himself to service as a minister. Acceptance of his announced career by parents, friends, and teachers plus his own determination confirmed his choice until illiberal criticism threatened his usefulness and he awoke to the fact that his inner needs were not along the direction in which inertia and his conscience had constrained him.

Jan 1, 1947

By A. P. Schissler

2013 has seen metals, industrial minerals, and coal all reduce in price due to market and geo-political factors. Many companies are taking write-downs to recalibrate their reserves and have enacted focused cost reduction programs. The public domain includes statements where companies have operating cost reduction goals in the $500 million range. Zero-base staffing & budget analysis is a means to achieve optimal employment and cost levels for a given level of production. The method involves measuring the work to be done similar to Lean. Lean is a method to review each step of production and remove anything that doesn?t add value or is necessary to complete finished goods. Zero-base methodology has been applied to mines worldwide producing realistic and sustainable levels of staffing and costs based on the quantity of work. The objective of this paper is to provide the framework of zero-basing with examples of application.

Feb 23, 2014

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By Oliver Smalley

Except for the work of Guillet, who conducted a systematic investigation on the zinc-replacing value of nickel in brass, and extended his investigation with a view to developing commercial high zinc content nickel brasses, the author does not know of any other systematic research on the subject. The most promising commercial alloys and their physical properties obtained by Guillet are given below: These test results scarcely justify the use of such quantities of so expensive a metal, and could have been obtained from ordinary commercial brass. For purposes of comparison, the physical properties of ordinary brasses, ranging from 70 per cent. to 50.1 per cent. Cu in both the cast and normalized1 conditions are included in 'Table 1. These incidentally furnish a useful standard of the properties of castings and of rolled, extruded and forged brass when correctly annealed. A close study of some of the well-known special brasses containing nickel reveals a series of alloys which bewilder by their complexity, and me can only hazard a guess at the function and commercial value of each of the many elements used.

Jan 1, 1926

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948

By R. Dell Davidson

This report contains the results of the work performed by Dayton T. Brown. Inc., Testing Laboratories, Bohemia, New York, under the Department of Interior, Bureau of Mines, Contract J0166089 entitled "Performance Testing of Air-Line Linking Components." The objectives of the program consisted of the following: 1. To conduct engineering tests that will provide data to recommend the performance criteria for air hose and piping connections. 2. To determine the requirements for restraining devices which are used to comply with MESA Health and Safety Standards 55, 56, 57,13-21.

Jan 1, 1978

By J. M. Steininger

The mechanism of flotation of sphalerite with sulthydryl compounds of different acidities has been interpreted in terms of chemisorption of unionized collector molecules on hydroxylated zinc surface sites. At a constant collector concentration of 1.5 x 10 -4 M, the upper pH limit of flotation has been found to be directly and closely related to the negative logarithm of the collector acidity constant, pKa The experimental results indicate that flotation is prevented when about 95% of the collector is ionized. At low pH, collector adsorption decreases because of the reduction in number of hydroxylated zinc surface sites. These two effects explain why sphalerite does not float with the more acidic sulfhydryl compounds. Typical anionic collectors for sulfide minerals are short chain xanthates or dithiophosphates which are nearly completely ionized in the generally alka- line flotation circuits.1,2 Flotation mechanisms have therefore been usually interpreted in terms of ionic collector adsorption and competition with ionic depressants of the same sign as the collector. A few attempts have been made, however, to consider adsorption of neutral collector molecules. Contact angle measurements obtained by Wark and cox3 have been interpreted by Cook and Nixon4 as representing adsorption of the free acid molecules on sulfide minerals such as pyrite, galena, chalcopyrite, and sphalerite. Cook and Nixon tried to show that the free acid concentration of the collector was substantially constant along the curves relating collector addition and minimum pH for bubble adherence. However, in a review of the subject,5 Sutherland presented new data on the flotation of pyrite with mercaptobenzothiazole which did not support the hypothesis of constant concentration of either collector ions or collector free molecules. He further showed that, with the assumption of constant occupation of surface sites, both theories lead to relations between pH and collector addition having similar mathematical expressions. In fact, with the more likely assumption of variable occupation of surface sites which results in more complex relationships, it appears impossible to

Jan 1, 1968

By Greg Sanders, Michael Gilbert, James G. Shaughnessy

"A new raw water intake from the South Holston River to the Kingsport water treatment plant is under construction. The exploration for the 335 meter long horseshoe shaped tunnel design took advantage of the site topography along the alignment to better define the complex geology consisting of Knox Limestone and Sevier Shale formations separated by a fault zone. To assess the geological conditions and to determine the extent of the fault zone, a 183 meter long horizontal boring and geophysical investigation was performed along a portion of the tunnel’s horizontal alignment. Explorations defined the fault zone width at approximately 5 meters and packer testing along the alignment provided a means of estimating groundwater inflows. As the tunnel excavation advances, comparisons of exploratory data versus encountered conditions will be made. This paper provides details on the geotechnical investigation, lessons learned, and the influence of the geology on the tunnel design. PROJECT OVERVIEW The Kingsport WTP is supplied with raw water via the South Holston River. The City of Kingsport (City) owns and operates the Kingsport Water Treatment Plant (WTP). The existing raw water intake system, consisting of pumps, power supply, raw water piping and appurtenant facilities has been determined to be vulnerable to failure. The original Raw Water Pump Station (RWPS) was constructed in 1928 as part of the original Kingsport WTP project. The 1928 RWPS operated until 1970 when it was replaced by the existing RWPS. This existing system still utilizes the 1928 piping and piping tunnel. Improvements to the RWPS hydraulics and capacity are required to meet the City’s future water treatment needs. The system extracts water from the South Fork of the Holsten River and coveys it via three pressure pipelines to the WTP. The conveyance piping exits the RWPS, ascends approximately 23 m up a near vertical rock outcropping then enters a 120 m long tunnel. Upon exiting the tunnel the piping continues underground to the WTP. The drill and blast tunnel is horseshoe shaped and nominally 3.3 m high by 3.3 m wide. The easternmost 62.3 m of the tunnel is without any type of support. The remainder is lined with concrete. According to the City of Kingsport, the concrete lining was installed in the 1970’s as part of upgrades to the facility. An evaluation of the current facilities concluded that the conveyance piping was in poor condition and required replacement."

Jan 1, 2016

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By A. Metzer

When paraffinic gases (ethane, propane, butane) are used as the gas phase in flotation systems, the initial rate of flotation and recovery are generally increased as compared with air. The mechanism of the effect of paraffinic gases in flotation was studied and it was shown that they co-adsorb with the collector ions on the mineral-aqueous solution interface. The effect of this co-adsorption was interpreted in terms of apparent increase of the effective chain length of the collector by the co-adsorbed gas. Adsorption densities, contact angles and flotation behaviour were studied on the following systems: a) Quartz - dodecyl ammonium chloride - ethane and propane b) Calcite - sodium oleate - propane and butane. The positive effect of the co-adsorbed gases is a maximum at low collector concentrations or where critical conditions for flotation with air prevail.

Jan 1, 1974

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980