Search Documents

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington, The investigation consisted of transit and topographic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds Were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and analyzed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing new sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest.

Jan 1, 1948

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

By G. Akdogan, M. Tadie, A. Tapfuma

The Southern African region contains abundant gold tailing heaps that are an environmental concern due to dust pollution and chemical contamination of nearby water bodies. Nevertheless, these heaps contain gold with potential to be extracted for financial gain. In this study, the feasibility of extraction of gold from a Witwatersrand gold tailings using glycine was investigated using a two-level full factorial design. Effects of variables such as glycine concentration at levels of 0.5–1.5 M with a solid–liquid ratio of 50–200 g/L were investigated. Although the solid–liquid ratio used in this study was below the industrial norm, it provides a starting point for investigating the applicability of this technology. To enhance the gold extraction, potassium permanganate pretreatment and copper ion addition were adopted. The results revealed that 91.4% gold extraction was achieved after 24 h pre-treatment of the tailings using 2 g/L potassium permanganate followed by subsequent leaching using 1.5 M glycine at pH 12, with 50 g/L solid–liquid ratio and 2 g/L copper ions. Statistically, the solid–liquid ratio and potassium permanganate pre-treatment of the tailings were found to be significant at 95% confidence interval, whilst interactions of copper ions and glycine concentration were significant factors. The work demonstrates that potassium permanganate pre-treatment prior to glycine leaching of low-grade secondary gold resources, such as tailings, can be beneficial. Furthermore, the methodology developed in this work provides an opportunity for further investigation of the recovery of gold hosted in complex mineralogical matrices.

Apr 14, 2024

By M. Ataei, F. Sereshki, R. N. Masir

Given the inherent risks and disruptions in underground coal mining operations, strengthening the resilience of critical infrastructure has become a vital priority. This paper aims to evaluate the resilience of the underground coal mining environment using historical data and expert judgment. The study serves as a framework for optimising the utilisation of critical infrastructure to minimise operational disturbances. To achieve this, a practical methodology has been developed, incorporating nearly two and a half years of collected operational data, a hierarchical structure, and a systematic approach. Furthermore, a case study is conducted to demonstrate the real-world applicability of the proposed method. Finally, the resilience index isintroduced as a straightforward summation of ranked impact factors, providing a clear metric for resilience assessment.

Dec 15, 2025

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

By Francis Lucas

EACH year we gather in this auditorium to honor the memory of a . distinguished American metallurgist and educator. I cannot bring to you reminiscences of Prof. Henry Marion Howe as other lecturers have done. It was not my good fortune to enjoy the privilege of studying and ,working under his direction. As I have reflected on the published works of Professor Howe, it has seemed to me that his mind was trained on the nature of metals and on the mechanism which produced known but unexplained effects. He was interested in controlling and regulating the causes so as to produce specific effects, useful in serving mankind. I recall an afternoon in May, 1925, when, at the invitation of Mrs. Howe, I visited his former home, Green Peace at Bedford Hills, N. Y. The purpose of my visit was to receive at the hands of the widow -an engraving of Professor Howe, a reproduction of a painting from life. Mrs. Howe showed me his study. The walls of this large attractive room, brilliantly illuminated by the spring sunshine, were literally covered with the scrolls of honors and of decorations which had been conferred on Professor Howe by governments, academies, universities, societies and. institutions the world over. As we walked about the room, she pointed out the significance of each honor and recited a few details of each occasion. I sensed the pride with which Mrs. Howe, then in the late autumn of her life, told me of her husbands' achievements, of his struggles, of his disappointments and of his successes. There was a surprisingly familiar note in the recital to which I was listening. I have found the same theme running as a disconnected thread through the written accounts of the lives of most men of science. We then went to the drawing room to chat for a few minutes before I said my farewells. As we seated ourselves, Mrs. Howe turned to me and asked: "Mr. Lucas, what of this great microscope of yours? Cannot it be applied to the study of disease? What a great blessing it would be if it could be directed to relieve the suffering of mankind."

Jan 1, 1931

By Peter Grandone

"INTRODUCTION The Bureau of Mines, recognizing the importance of knowing the evapor¬ation losses of aviation gasoline as larger quantities of this material must be stored, has made studies at a large refinery in the Texas Panhandle area during the past 13 months to determine the magnitude of the losses, by evaporation, under different storage conditions. Proper storage of aviation gasoline is very important, not only because large supplies are being stored for military use but because the specifications to which his fuel must conform are very rigid. Aviation gasolines that conform present-day specifications are blended from base-gasoline stocks (in some instances relatively pure hydrocarbons), each of which has different physical and chemical characteristics. Consequently, partial loss of any one of the more volatile components from the blended fuel results not only in material loss of the blended fuel but also may affect the characteristics or performance of the gasoline. One characteristic that has considerable influence or the vaporization tendency of gasoline is vapor pressure; and although the vapor pressure of aviation gasoline usually is lower than that of average commercial motor fuel, the quantity of certain components having relatively higher vapor pressure is greater in aviation gasoline, so that under prolonged storage the evaporation loss of these components may be appreciable."

May 1, 1943

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Robert Hall

The Lynch Creek beryllium-tungsten prospect was investigated as part of the domestic beryllium resource studies by the Bureau of Mines. This prospect is in the Birch Creek mining district, Lander County, Nev., 9 airline miles south of Austin. A tungsten mine was operated intermittently from 1952 to 1957. Beryl was identified in the pegmatite dikes in 1960, and the lode claims were relocated. No beryl has been produced. Rocks in the area are Paleozoic sediments2 cut by pegmatite and aplite dikes and quartz stringers. Beryl occurs in random pockets, as disseminations throughout the dikes, and in occasional pockets in the quartz stringers.

Jan 1, 1962

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994

By Peter G. Chamberlain

The Bureau of Mines is conducting research to boost domestic production of manganese. Virtually no mining exists in the low grade and/or small deposits that occur in this Country. One large, low-grade manganese deposit located in westcentral Arizona--The Artillery Peak district--was extensively studied and sporadically mined during the 1940's and 1950's. Although manganese mining in the district has been long dormant, recent studies indicate that the deposits may be amenable to economical production by heap and/or in situ leaching methods. A conceptual design for an in situ leaching system features undercutting and blasting a block of ore, leaching with SO2, and extracting the manganese as a sulfate or oxide. Possible applications to other manganese deposits depend upon formation permeability and specific manganese mineralogy.

Jan 1, 1981

By Sang-Mook Lee

The Manus back-arc basin behind the New Britain Trench is one of the major sites of active seafloor hydrothermal vent-fields which are considered to be modern-day analogue of felsic volcanic-hosted polymetallic massive sulfide deposits abundant in ancient geological record. Many of these deposits represent multi-million dollar resources, and yet very little are known about the fundamental processes leading to their formation. In November 2000 January 2001, the PACMANUS hydrothermal system in this region will be targeted by the Ocean Drilling Program Leg 193 to investigate the internal anatomy. A number of observations that suggest that the tectonic, magmatic and hydrothermal processes in the eastern Manus basin spreading center are unusual in that they can not be explained by a simple back-arc opening due to subduction of the New Britain Trench. Geochemistry of submarine volcanoes in the eastern Manus basin, for instance, shows affinity to arc rather than back-arc type volcanoes. Yet these submarine volcanoes lie too faraway from the Benioff-Wadati zone. One hypothesis is that the magmatic and subsequent hydrothermal activity of this region is a direct result of the irregularities in the deep crust and upper mantle structure and that the tectonic process is controlled by the sharp inflection of the New Britain Trench. According to this hypothesis, the two major southeast-trending strike-slip faults in the eastern Manus Basin, Djaul and Weitin Faults, should extend farther down and join to the New Britain Trench. They would form a transform arm of the triple junction with the New Britain Trench southeast of New Britain Island and southwest of Bougainville Island forming the other two arms. A trench-trench-transform triple junction can not be stable over time, and therefore a slight change in the plate velocity may lead to a dramatic change in the configuration of the plate boundaries. If so, the instability of the triple junction may cause large tectonic deformations, such as mantle uplift under the Manus basin due to mantle rupturing by transform faults, and therefore may explain the arc-style volcanism and unusual compositions of hydrothermal deposits in the eastern Manus basin.

Jan 1, 2000

By Venancio Astucuri

Ante la incompatilbilidad entre las competencias de los ingenieros de minas y las necesidades de mercado, se plantea la acreditación como un mecanismo de solución en la formación de estos profesionales. En ese sentido, el presente texto señala la acreditación académica como mejora en el proceso de formación profesionales de los ingenieros de minas. Las principales brechas son: la escaza preparación de los estudiantes en los cursos de inglés y matemáticas, deficiencia de trabajo en equipo, autoaprendizaje, manejo de Comunicación y la no obligatoriedad de pasantías y permanencia de estudiantes en la empresa en la formación de ingenierios de minas. Las posibles soluciones estriban en establecer objetos educacionales de cada escuela donde se busca resolver problemas de ingeniería utilizando los principios fundamentales de la ciencia, matemáticas e ingeniería de minas, que los estudiantes sean comunicadores líderes con los equipos que participa y poseer una apreciación para la minería como un negocio, y comprometerse en la formación continua y desarrollo profesional.

Jul 1, 2016

By Michael A. Markowitz, Alok Singh

"Molecular self-assembly of phospholipids and other amphipathic molecules offers a versatile approach to form self-organized microstructures in various morphologies. Stabilization of microstructures in specific morphologies by polymerization renders them useful for practical applications in areas ranging from controlled release technology to template mediated synthesis of metals. Our efforts are focussed on the development of polymerizable biomembranes derived from phospholipids, their properties and utility e.g., as stable templates for studying chemistry at the lipid interface. Polymerized vesicles formed from mixtures of 1,2-bis(tricosa-1 O,12-diynoyl)-sn-glycero-3-phosphocholine, 1, with corresponding lipids having phosphohydroxyethanol,2, or -hydroxypropanol,3, headgroups have been used in electroless metal plating of vesicle surface with gold utilizing selective binding of Pd(NH3)4 2 + to 2 or 3. The surface bound palladium ion served as catalyst for metalization. Metalization of polymerized vesicles constructed from charge neutral diacetylenic phosphocholine,1, did not occur using this process. The headgroup structure of the negatively charged phospholipids and the degree of vesicle polymerization had an effect on the stability of the vesicles after metalization. Vesicles formed from a mixture of 1 with polymerizable diacetylenic phosphatidic acid, nonpolymerizable 1,2- dipalmitoyl phosphohydroxyethanol or 1,2-diacyl phosphohydroxyethanol (from soy lecithin) were not stable to metalization process. The metal coating of the vesicles was examined by electron diffraction and revealed that the gold metal on vesicles was polycrystalline and face centered cubic. The results demonstrate the utility of polymerized synthetic membranes as template for easy and efficient synthesis of nanoparticles. IntroductionPhospholipids, synthetic or natural, provide a simple and straight forward route to construct membranes in a variety of morphologies due to their inherent property of selforganization in the presence of water[1]. Vesicles are closed spherical structures comprised of concentric walls made from lipid bilayers. Vesicles are morphologically simple structures with enormous technological potential. Polymerizable phospholipids prepared by incorporating a polymerizable group in the molecules demonstrate physical properties comparable to their non-polymerizable counterparts and have the added virtue of providing enhanced physical and chemical stability to the membranes[2,3]. The size, shape and properties of the organized assemblies are dependent on the lipid structure and the nature of the aqueous environment[4,5]. The headgroup geometry, surface charge density, and spatial arrangement of the phospholipids are known to affect the surface behavior of the lipid membranes, which is evident through their interaction with other molecular (hormones, antigens, antibodies etc) or lomc species. Since phospholipid headgroup structure and charge can be modified either synthetically or by chemical perturbation of the aqueous medium (e.g., pH or ionic strength), phospholipid membrane surfaces offer a potential for developing novel strategies in those areas which involve the use of molecular reactive sites. One such strategy which could be envisioned explores the use of molecularly engineered phospholipid assemblies to design and prepare template structures to regulate formation of ordered materials [6]."

Jan 1, 1994

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013