Search Documents

By Bradley Stoughton

AT THE meeting of the Board of Directors on May 20, the resignation of Bradley Stoughton as Secretary of the Institute was presented and regretfully accepted by the Board. The letter of resignation follows : Gentlemen: About two years ago, I indicated to the President and some members of the Board my belief that the office of Secretary of the Institute should not be a permanent one. It is my observation of events, not only in our own Institute, but also in several sister societies, that too long a tenure of office by the Secretary inevitably leads to a situation which is not good either for him or for the society. After submitting this in writing to the Directors on February 17, 1920, I was overpersuaded by members of the Board to defer resignation until a more convenient time for the

Jan 1, 1921

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By S. Agatzini-Leonardou

The objective of this work was to prove repeated loading capacities and investigate the selectivity of physically stabilized algal biomass from Spirulina platensis and Chlorella sp. for the removal and recovery of cobalt, nickel and chromium from laterite heap leach liquors. The testwork was carried out on a bench scale in small glass columns and proved that it was possible to immobilize the biomass on the highly porous surface of pumice stone (kissiris). Nickel and cobalt could be removed from pure aqueous solutions of each metal by the immobilized cyanobacterial biomass. Nickel and also cobalt biosorption was sensitive to the initial solution pH. Cobalt recoveries up to 80% were achieved after 5 loading cycles, from low concentration solutions, at pH 6.0. Nickel removal was complete under the same conditions, whereas chromium sorption was ineffective. Desorption of the metal loaded columns was effected by dilute sulfuric acid. The algal species giving the best adsorption capacities for the metals under consideration was selected for further experimental work with real laterite heap leach solution produced by column leaching. A statistical analysis of all obtained results was conducted using the fraction of metal removed as response. The ratio "mass of metal removed to mass of protein contained in the immobilized cells" was determined as well. The described method might be applicable for recovery of cobalt and nickel from diluted laterite heap leach solutions, such as heap wash waters, or for their removal from waste streams of a hydrometallurgical extraction process.

Jan 1, 1997

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept&apos;s economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By D. J. Barratt

What is meant by "Minimizing Risk"? This paper explores some of the factors encountered in plant design which can affect the success of a mineral processing plant in terms of its planned output, quality of product and recovery. Any deficiency in either one of these objectives means lost revenue at the start of a project and reduced present value for the mine life. Time is money. Related factors such as project conception, feasibility studies, capital cost and operating cost estimation and mining studies have been covered in a recent paper (1) from which material for this paper has been drawn. What follows is a discussion of the principal factors which can influence the success of a project with particular emphasis placed on processing concepts.

Jan 1, 1983

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

By Frank T. Sisco

The discovery of phosphorous is usually credited to the German alchemist Brand, in 1669, and the element was rediscovered the next year by Boyle in England. IT was more than 100 years later, however, before its presence was detected in high-carbon iron produced in early blast furnaces. In 1781 the German chemist Meyer published the results of his investigation on the ?white earth? that he had found in cast iron made from bog ores. This white earth was metallic in appearance, it was extremely brittle, it was readily fusible, and it was not attracted by magnet. Meyer noted that cast iron containing this white earth was more fusible than other cast iron, and he was sure that he had discovered a new metal ? for which he proposed the name Wassereisen, or the Latin term Hydrosiderum. Two years later the distinguished Swedish Chemist Bergmann made the same discovery, finding a ?white calx? in cast iron, which he also mistakenly considered to be a new metal, and for which he proposed the Siderum.

Jan 1, 1944

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

"The Morris Island Lighthouse (MIL) is located between the jetties leading to the Charleston Harbor and Folly Beach, S.C. The present structure is the third lighthouse to occupy this location. The first navigational aid was erected in 1673, and consisted of a raised pan filled with pitch, which was set afire at night to guide early ships. The next structure was built in 1767, and constituted the first real lighthouse, standing 42 ft (12.8 m) in height. In 1838, a second lighthouse was built on the site, and it measured 102 ft (31 m) in height and featured a revolving light. This structure lasted until 1862 when Confederate troops, during the Civil War, destroyed it to deny its use to Union troops.Navigators steered these waters without a lighthouse for nearly a decade until 1876, when the current structure was built under the direction of the U.S. Army Corps of Engineers (USACE). In 1886, the Charleston area suffered a M7.6 earthquake. Significant damage was caused throughout much of the area, including a slight “list” of the lighthouse to the northeast. As a result, the cast of the beacon was reduced from 18 mi (29 km) to about 6 mi (9.7 km), causing much distress to navigators until the beacon platform was releveled and remains at this list to the present day.Conditions for ConcernThe current lighthouse was originally constructed about 1,200 ft (366 m) from the shoreline. Over the years, USACE has undertaken several programs to meet the increased shipping and navigation demands in the Charleston Harbor. Around the turn of the last century, two jetties were constructed, which drastically changed the approach direction for ships entering the harbor. In subsequent years, the harbor began to experience accelerated siltation."

Jan 1, 2017

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By George Otis Smith

A YEAR ago, ,at the Institute&apos;s dinner, I closed my A remarks with the words: "The scientist devotes his life to the advancement of learning; the engineer gives his to the advancement of living." May 1 begin tonight where I left off then and speak first of the distinction between science and engineering? This difference is a difference both in purpose and in method: it is the sharp contrast between theory and practice; it marks the broad gap between dream and attainment. Sometimes it happens that the investigator is also the builder and applies what he discovers, yet the distinction between science and engineering serves to point out the broad dependence of the engineer upon his brother the scientist. You remember .the old - saying that "where there is no vision the people perish" translate this into modern experience and we may say that "where there is no science, the engineer fails."

Jan 1, 1929

By John D. Corrick

The environmental and nutritional characteristics necessary for maximum copper extraction from a low-grade ore by Ferrobacillus ferrooxidans have been explored as have many of the limiting parameters. Criteria considered were oxygen consumption, copper extracted, soluble copper concentration, temperature, pH, particle size, nutrients, and other inorganic salt concentrations. A set of environmental and nutritional conditions were developed for E. ferrooxidans Which supported cell reproduction and maximum microbial oxidation of a low-grade copper sulfide ore. Percolator tests conducted under these optimum conditions resulted in an 18 percent increase in the quantity of copper microbially extracted over that extracted under conditions considered to be standard. Manometric tests determined those extremes of environmental conditions and nutritional factors Which were detrimental to the extraction of copper by E. ferrooxidans.

Jan 1, 1965