Search Documents

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

By Jizeng Zhao, Li Liu, Weiqing Chen, Jinxia Meng

This paper discusses the utilization of chromium slag, which presently has no useful application in China, as a resource. The following research has been done in this paper: (1) After determining the composition and properties of chro- miumresiduewedecidedtotesttheideaofusingchromiumslagasacomponentin synthetic MgAl O spinel material. (2) Through experiments on sintering and 2 4 electric melting of refractory materials we determined the best conditions for a practical process. (3) We compared the performance of the refractory material obtained with traditional spinel refractory materials and confirmed the excellent performance ofoursystem. The results show thefeasibilityofpreparing MgAl O 2 4 spinel material from chromium slag by electric melting. (cid:1) (cid:1)

Mar 1, 2018

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By Maria Sílvia Camarão de Sousa

Nesse estudo foi fabricada uma matriz hipoeutética de Al-2%Ni e adicionado nela a concentração 1,0 % de nanotubos de carbono de paredes múltiplas (NTCPM). A fabricação do material estudado aconteceu por fundição e resfriamento unidirecional brusco originando grãos predominantemente colunares. Os ensaios mecânicos mostram que concentrações maiores de nanotubo na matriz provocam acréscimo na propriedade mecânica e que em áreas mais distante da base extratora de calor a microdureza aumenta. As curvas de tensão-deformação, para os materiais estudados, evidenciaram que o acréscimo de 1% NTC na liga de Al-2%Ni teve como resultado, uma alta deformação plástica. No entanto, o endurecimento do material não afetou o aumento da resistência à tração.

Aug 17, 2017

By Ken Deter

I have some general comments on optimizing profitability based on working in heap leach operations in tropical environments. Many of my planned comments this morning have been stated earlier in the Conference. I get the opportunity to say only a few words, and follow up on some specific comments and concerns. In normal operations, stack the ore higher, where possible. The surface area of the stacked ore controls the total solution volume that can be sprayed on the pad at a specific time period. With higher lifts, solution will contact more ore particles as it percolate through the lift, and therefore the solution grade flowing through the base will be increased, whether it is freshly stacked or almost completely leached ore. This also allows more tonnage to be stacked per lift on the pad, decreasing conveyor movement and downtime. Increasing from 6 to 8 meter (20 to 26 feet) lifts have worked successfully, and some mines are using 10 meter (33 feet) lifts in 10,000-15,000 dmtpd plants. The same concept will work with smaller plants, but initial 6 meter lifts should be used until the start-up period has shown the leaching is working as planned. As the stacked ore lifts get higher, the solution flowing through the highest lift is diluted by solution retained in the lower ones. Eventually no real increase is noted from putting fresh ore in service, and gold production rate suffers. To address the dilution problem, an HDPE liner should be installed between each 2 to 4 lifts, depending on each site specific lift height, recovery, % slump in the lift, recovery rates, and grade treated, among others. The surface of the previous lift should be leveled and sloped to control the effluent draining from the planned lift, then the liner is placed, including berms and discharge pipes. The intermediate HDPE liner does not need to be completely sealed as would be the case with the base liner, and can accept some solution penetrating into the lower lifts. A one-mm (40-mil) thickness liner can be used. This intermediate liner allows the upper lift(s) higher-grade effluent to report to the pad discharge point. This will maintain higher gold solution grades going to the ponds. The slopes of the previous lifts should not be covered with HDPE in this concept, and precipitation falling on the lower lift slopes and benches can be directed to barren or surge ponds.

Jan 1, 1999

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Versiane Albis Leão

This work aims at the selection of an appropriate eluant for cyanide recycling using ion exchange resins. Based on a literature review as well as on experimental results, the elution of resins loaded with copper and minor amounts of iron and nickel is discussed. The resins Imac HP 555s, Amberlite IRA 900 (Rohm&Hass) and Purolite A860S (Purolite Co) were eluted using either NaCI, zinc and nickel cyanides, hydrochloric acid, sulfuric acid or acid thiourea solutions. The results indicate that saline solutions are effective only with polyacrylic resins (Purolite A860S), failing to desorb the metals, specially the nickel cyanocomplex, loaded on polystyrene-based resins. Cyanide solutions of both zinc and nickel are capable of eluting over 90% of the loaded metals. In contact with pure acid' solutions, iron precipitates onto the resin beads, as Cu(II) ferrous cyanideCu2Fe(CN)6.xH20. Thiourea is able to elute all the three metal cyanocomplexes owing to the increased solubility of copper cyanocomplexes in the presence of this complexing agent. The results demonstrate that a universal eluant is not available and the selection of the most appropriate resin-elution procedure should be based on the specific features of the system under consideration

Jan 1, 1998

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017