Search Documents

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By Michael S. Moats, John Bailey Fletcher

The performance of grinding media can be misrepresented in marked ball wear tests due to galvanic interactions between dissimilar media. The possible galvanic interaction of media materials during marked ball wear tests has not been adequately explored. Corrosion rates and potentials of modern high carbon steel and high chromium white iron grinding media materials were measured using electrochemical testing as a function of pH and chloride content in a simulated mill water. The results replicate previous research with the high chromium white iron sample being more noble (higher corrosion potential) and corrosion resistant (small corrosion current) than high carbon steel. Using the experimental data and corrosion theory, the effects of galvanic coupling on corrosion rates were calculated to examine what could happen during a marked ball wear test or when a mixed media charge is present. This analysis indicates that high carbon steel can cathodically protect high chromium white iron leading to significant decreases in the corrosion rate (up to 99%) of this material during marked ball wear tests. The magnitude of the protection is a function of the pH of the mill water.

Dec 21, 2022

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By C. O. Riggs

Geotechnical exploration in North America, in particular, exploration for deep foundations analyses, is currently and generally performed following the most basic sampling and insitu testing methods and techniques. Some would surely say that the state-of-practice severely lags the state-of-the-art. Probably more than 90% of all deep foundations, both driven piles and drilled piers, installed in North America are initially analyzed and designed, i. e. geotechnically, on the basis of either the soil penetration resistance obtained by performing the "Standard Penetration Test" (SPT), or from laboratory shear tests performed on samples obtained using 76-mm (3-in.) nominal diameter, thin wall, "Shelby tube" samplers. The use of design data obtained with other exploration methods and devices, such as bore hole pressure meters, flat plate dilatometers, even cone penetrometers, occur on the fringes of practice and often in conjunction with the use of the two simpler methods of analysis. This basic approach probably represents an attempt of the profession to use, as much as possible, common, easily understood and easily communicated procedures in all geologic environments. The characteristics of drill rigs with the required drilling and samplng tools vary somewhat from region to region in North America according to the physiography of the area of use, the types of exploration data required on a day-to-day basis, the philosophy of the engineers and geologists that use the exploration data and the financial resources of the drill rig owner. The physical capability of the exploration drill rig used on a project can have a significant effect on the quality of samples or insitu tests. The physical configuration and the quality of the drill and the drilling, sampling and testing tools not only provide the mechanical capability to obtain data but affect the attitude of the field exploration crew and the quality of work. This complete presentation is taken, for the most part, from a book in preparation for publication: "Geotechnical Exploration and Site Characterization" by C. Riggs, A. Hatheway and N. Schmidt. The book is scheduled for completion during 1987.

Jan 1, 2010

By E. Lee Cameron

The old mine workings on four barite-fluorite veins of the Lake Ainslie district, Nova Scotia, were opened recently and channel sampled. The samples were then forwarded to the Ore Dressing Laboratories, Bureau of Mines, Ottawa, for chemical analyses. Following the analyses, the sample rejects were combined to form bulk samples, representing ore from each vein, for small-scale batch test work. Tonnage samples from the veins, for pilot mill testing, were submitted when requested by the Bureau. The results of the analyses on the channel samples showed that there are two grades of ore in the di strict, represented, for test purposes, by the Trout River vein and Johnson vein ores. Small-scale and pilot-plant test work was undertaken on both these ores. The Trout River ore is amenable co concentration but, because of the high-barite-co-fluorite-co-calcite ratio, a fluorite concentrate was not obtainable from the Johnson vein ore as received. However, Johnson ore blended in a 1 :1 ratio with Trout River ore gave a mill feed that was readily concentrated. The test work on these ores showed that the following concentrates are obtainable : (a) A barite concentrate, with a recovery of 85 to 95 per cent of the available barite, analysing 93 co 96 per cent BaS04, 4 co 6 per cent CaF,, and 0.5 co 2 per cent CaCO3. (b) A fluorite concentrate, with a recovery of 80 co 85 per cent of the available fluorite, analysing 94 to 97 per cent CaF, , 1 to 3 per cent BaSO., and 1 to 3 per cent CaCO3

Jan 1, 1945

By Armando Fernandes da Veiga Rodrigues

Itabirito é um minério de fero encontrado no Brasil. As reservas futuras de Itabirito requerem moagem para atingir o grau de liberação necessário para concentração. Os circuitos convencionais de cominuição adotados em projetos de Itabirito consistem de três estágios de britagem seguido de moinhos de bolas. Estes circuitos demandam uma alta frequência de manutenção e uma grande área de construção. Por esta razão um estudo de bancada e piloto foi conduzido para entender a rota de cominuição de Itabirito utilizando moinhos autógenos (AG ou FAG) e semi-autógeno (SAG). Os testes piloto demonstraram que moinhos SAG e AG são apropriados para a cominuição de Itabirito.

Aug 1, 2018

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By C. E. Julihn

In the past few years the advance of the Sunshine mine to national prominence as the chief silver-producing mine of the United States has revived interest in the area in which it is situated. Although this area lies between the great lead-Zinc-silver mines at Kellogg and those in the vicinity of Burke and Mullan it was generally presumed to be almost barren, as little ore had been found there until substantial ore bodies were developed on deep levels of the Sunshine mine. In early days it was called the "dry belt" because its ores were siliceous and contained little lead; but the classification of ores in smelting as wet or dry, although once customary, has long been obsolete The area will therefore be referred to in this paper as the silver belt of the Coeur d&apos;Alene district because the value of its ore is due chiefly to silver, the current production of which is large, providing over 60 percent of the silver output of Idaho. Silver Belt - Its Limits and Character With a daily production of half a ten of silver or more from the Sunshine mine, the silver belt has become the scene of extensive exploration at many properties, and the outlook for its future seems promising enough to warrant the lively interest now being displayed in the area by the public.

Jan 1, 1936

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By R. Bainbridge

THE cinnabar deposits of the Consolidated Mining and Smelting Company&apos;s Pinchi Lake property, situated near Fort St. James, B.C., were discovered and reported on by a Dominion Government geological party in 1937. Claims were staked by a group of local prospectors and, later, the Consolidated Mining and Smelting Company of Canada, Limited, took an option on the property. By the fall of 1939, exploration work had indicated ore of commercial quantity and grade, and laboratory tests had shown that standard methods of reduction, namely, roasting of the ore, followed by condensation of the mercury vapour produced, would result in satisfactory recovery. In June, 1940, construction of a 50-ton unit arranged for wood firing was completed and operation commenced. The installation consisted of a 46 in. by 60 ft. rotary kiln (see Figure 1) followed by a 14-in. Sirocco cyclone, a cast-iron condenser unit, and a 1,700 c.f.m. fan, exhausting to a stack. Other equipment included a 9 in. by 18 in. Denver jaw crusher with the necessary bins and feeders. As the need for mercury was urgent, because of war requirements, construction of a duplicate unit was begun almost immediately. This first extension started operation in January, 1941, and the plant was then capable of treating about 150 tons of ore daily.

Jan 1, 1945