Search Documents

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using existing European methods. To modify these methods for domestic conditions, the Bureau of Mines, U.S. Department of the Interior, developed a method of assessment to evaluate the lithological effects on subsidence in the Northern Appalachian basin by examining data collected from 16 longwall panels in the coalfield. The assessment is partially completed, and the results to date show that the ratio of maximum subsidence to the extraction thickness, known as the subsidence factor, can be expressed in terms of the width-to-depth ratio by a simple exponential equation which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site and can be expressed in terms of the percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By OWEN H. PERRY

One of man's primary tools is the ordinary screen. Whether of mesh or punched plate, it is fundamental in principle, primitive in its origin, and common in its application through all the world; and yet the screen goes only a part of the way toward the completion of its job of separating materials according to size. It will give a practical and continuous separation according to "size," as generally understood (accurate according to the breadth), but the accurate and continuous separation as to thickness is not a practical function of the screen. Still, all through history, the thickness of particles of material must have been important to many people; therefore, one would expect that some standard method of sizing for thickness would long since have been evolved and that equipment applying that method would be readily available to any in¬dustry. This, however, seems not to be so.

Jan 1, 1949

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By B. McFadzean

Thiol collector mixtures are commonly used in the flotation of base metal sulfides and platinum-bearing ores. There are synergistic benefits claimed for these collector mixtures, with mixtures lowering total dosage requirements, improving coarse particle recovery and the rate of flotation. Some of the secondary collectors are known to have frothing effects. Therefore, a previous study aimed to decouple froth and pulp effects and considered only the bubble-particle attachments in the pulp. This was achieved through microflotation experiments, where various ratios of the ethyl and isobutyl chain lengths of xanthates, dithiocarbamates and dithiophosphates were used as collectors. Results from these experiments showed a marked increase in galena recovery using mixtures of xanthate with either dithiophosphate or dithiocarbamate. In the current study, the froth phase was introduced in the form of batch flotation studies to determine whether benefits noted during microflotation experiments would be carried through to a more realistic froth flotation scenario. The findings show that there was no significant difference in the flotation recovery between the best single collectors and mixtures of these collectors. In addition, single collectors that behaved poorly in microflotation experiments showed good flotation performance in the batch flotation experiments. The differences between the microflotation results and the batch flotation results are attributed to differences in particle froth stabilizing properties and/or differences in energy input between the microflotation and batch flotation cells. In addition, galena and pyrite showed marked differences in frothing effects and in their preferences for collector type. Keywords: froth flotation, collector mixtures, sulphide minerals

Sep 1, 2012

By J. Oré Iwanaga

El presente texto señala el uso de geocontenedores como una alternativa en la deshidratación de lodos líquidos ( relaves) a través del programa MATLAB que permite la determinación de los parámetros de diseño más importantes. La ejecución del programa se realizó en la planta concentradora de la Compañía Minera Raura, ubicada en la cordillera occidental entre Huánuco y Lima, sierra central del Perú donde se estableció la presión de bombeo (Po) y resistencia del geosintetico (T),a partir de datos conocidos como: perímetro (L) y peso específico del lodo líquido.

Jul 1, 2014

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By L. Diels

About 45% of the contaminated sites are dealing with heavy metal problems. Metals are spread in the environment by mining activities, surface treatment and non ferrous processing. As heavy metals can not be degraded, removal or immobilization (leading to bioavailability reduction) are the only risk reducing measures that exist. The currently best available technique for remediation of heavy metal contaminated groundwater is to pump the contaminated water and to treat it in a wastewater treatment plant installed on the surface. Next to this often used, but expensive, pump and treat technologies, heavy metals can be immobilized by inducing sulfate reducing bacteria (SRB) to transform the sulfates, that are very often present in the same groundwater (due to the metal mining or processing activities), into sulfides. These sulfides will precipitate the metals as insoluble metal sulfides. At the moment several studies have demonstrated the feasibility of this In Situ Bioprecipitation Process (ISBP) for the removal of heavy metals from ground-water as well at lab scale (batch and column tests) as at field scale. However, some questions arise concerning the continuation of the process, the efficiency and the sustainability of the precipitates. The presented study will try to answer these questions. The study is based on more than 10 different studies, all done by the same authors, on different groundwaters and aquifer samples. The presentation will give an overview of the guidelines necessary for a correct and successful bioprecipitation process with stable metal sulfide precipitates. An important question in the ISBP is related to the sustainability of the heavy metal precipitates. It could be observed that the interruption in the carbon source delivery also stopped the in situ bioprecipitation process. Depending on the metal also some release from the precipitate could be observed. It was shown that release can occur with Co and Ni. Aquifers, on which the metals precipitated during the ISBP, were treated in a sequential extraction process under an-aerobic and aerobic conditions. It could be shown that especially under the anaerobic conditions the Zn and Cd precipitates changed from the leachable and the exchangeable fraction to the organic or Fe-Mn fraction (i.e. from the unstable to the stable fraction). The same could be observed for Co and Ni but still some fraction was present under a more available form. On the other hand it could be shown that large differences were observed concerning the heavy metal speciation on the aquifer in function of the used carbon source during the ISBP. The molasses treated systems showed a much more available heavy metal fraction on the aquifer compared to the lactate or HRC® treated groundwater. The different speciation forms based on the use of different carbon sources will be discussed in detail. It will pay attention to the influence of the carbon source, the efficiency of the induction of the bioprecipitation process, the influence on the competence between sulfate reducers and methanogenic bacteria and the influence of low pH on the ISBP. It seems that acetate, which is also a degradation product of fermentation of some carbon sources, can inhibit some sulfate reducers. Also the relation between slow release compounds and immediately available compounds will be explained. Finally a pilot study will be presented showing the problems that can be encountered during this process. Focus will be put on the induction of the process, the keeping on of the process and the follow up of the process by the installation of in situ mesocosm socks. These results will allow the correct implementation of the ISBP with an eye on longevity and sustainability of the process and present the ISBP as a much more sustainable alternative to the pump and treat technology as measure for heavy metals contaminated groundwaters.

Jan 1, 2006

By W. R. Crane

Subsidence and ground movement are phenomena common to and attendant upon practically all large-scale mining operations, and under certain conditions may occur in all workings, large and small. The interpretation of the cause of failure in rock masses involves a study of the nature of plants of weakness common to all rocks. The dominating planes of weakness can readily be determined by observation in any given locality, and in order of importance in the study of subsidence are (1) faulting planes, (2) bedding planes, (3) joint planes, and (4) other prominent planes of weakness such as thrust and shear planes and contacts. This report has mainly to do with the third item, joint planes, and is a preliminary statement which t to be followed by a more complete report in bulletin form.

Jan 1, 1931

By Lee RJ

A significant basemetal province is recognised in the southern part of the Bonaparte Basin, Western Australia. Epigenetic stratabound carbonate hosted Pb-Ag-Zn mineral- isation occurs in dolomites of Tournasian age within a marginal marine transgressive carbonate and fine grained clastic sequence, spatially overlying the lagoonal facies of a Late Devonian reef complex. The deposits comprise coarse grained sulphide mineralisation characterised by high Pb:Zn ratios (10:1) and high silver (50 g/t) content. They occur at shallow depth, are flat to moderately dipping, and form a discontinuous mineralised trend at the margin of the Sorby Platform, which flanks a Precambrian basement high. Host rocks are predominantly sedimentary breccias and dolomitised footwall carbonates associated with a significant local unconformity transgressed by a siltstone cap rock sequence. The deposits are structurally related to synsedimentary growth faults, local basement highs and tensional en-echelon breccia systems. Fluid inclusion studies have concluded that mineralisation was deposited from a low temperature (85¦C-115¦C) saline ore forming solution. Lead isotope work reveals a Precambrian genetic source of the lead. Locally remnant textures after sulphates are recognised within the host sequence together with common bitumen and oil shows. Reduction of sulphate to H2S was possibly facilitated by either bacteria. activity, or by residual hydrocarbons which acted as a reducing agent. An alternative source of H2S may have been afforded by the thermal degradation of hydrocarbons. A 'mixing' genetic model is proposed for the mineralisation, which conceives the expulsion of metal enriched basinal brines followed by their precipitation as sulphides after mixing with locally derived reduced sulphur solutions at relatively shallow depths in their structural/stratigraphic sites of ore deposition.

Jan 1, 1986

By Paul Dean Proctor

The known northern ore zones of the New Lead Belt of Southeast Missouri extend to the drainage divide between the Meramec River draining north and east and that of the Black River draining southward. Intensive geochemical studies related to the environmental impact of the new mining area have been carried out in the vicinity of some of the newly developed mines, mills and smelter complexes (Bolter,1970; Gale, et al, 1973; Wixson, et al, 1969, 1977). Other investigations have related to fringe studies of the Northern New Lead Belt and the possible additions of heavy metals to the surface waters, stream sediments and selected aquatic life (Proctor, et al, 1975, 1976). Similar studies have been completed in the Joplin area in the Tri-State district, and in the fringe area near Springfield, Missouri (Proctor, et al, 1974). A surface geochemical study is currently underway on the lead-zinc-copper-cobalt-nickel province near Fredericktown, Missouri (Proctor and Sinha, 1977). This report summarizes some of the distribution patterns of heavy metals in the waters, stream sediments and selected aquatic life in the Upper Meramec River drainage basin just north and west of the known northern portions of the New Lead Belt of Southeast Missouri. The region studied includes the site of the proposed and somewhat controversial Meramec Dam and the reservoir site behind it. Some 3905 km2 (1508 mi2) are included within the drainage basin of the Upper Meramec River. Six distinct drainage areas are included within the drainage basin; 1) a combined, lightly industrialized and farm area around Rolla and Salem, Missouri representing the Dry Fork drainage; 2) a primitive, mostly forested area with some farms and cattle rancheseast and north of Salem, Missouri comprising the Upper Meramec River

Jan 1, 1977

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7, 200 kg (15, 900 lbs) per day or 61%. Metal loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change and fewer than 1 % got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2003

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

By A. Eitzenberger

This paper describes a study of seismic records from the Kiirunavaara mine footwall which were interpreted in relation with numerical models developed outside the study. Seismic data was retrieved from a portion of the mine and filtered with respect to the ratio between energy carried by an event's P (primary) and S (secondary) waves (Es/Ep ratio), local magnitude, and active mining depth. The data was analysed using Es/Ep ratios and Gutenberg-Richter graphs to determine the event origin, mechanisms, and minimum magnitude cut-off. The magnitude completeness was identified by studying the b-value stability and b-value differentiation between origin sets. It was shown that, by separating seismic events into the origin components shear, complex, and tensile based on Es/Ep ratios, a representative value for the magnitude completeness can be identified for a catalogue with a convex cumulative log curve. The majority of the events were shown to be of shear-slip origin based on the recorded Es/Ep ratios, with pure tensile events constituting only about 10% of the recorded data. Spatial and temporal event location patterns were studied and compared with numerical modelling results. The comparison showed a correlation between shear-slip seismic events and volumes experiencing high differential stresses in the lower part of the footwall. In the upper part of the footwall the results did not reveal any clear correlation between observed damage in drifts and seismic event locations. The concentration of seismic events in the lower portion of the footwall is discussed in the context of rock mass displacements. The results indicate a possible connection between mine seismicity at depth and damage observations in the drifts in higher non-seismic areas by seismic softening and subsequent lateral expansion of the rock mass.

Jan 1, 2017

By Steve Karl

"The global underground construction and tunneling industry is in pretty good shape. Billions are being spent in shoring up aging infrastructure in the United States and other places, and new underground projects are being put out for bid.With each new project, comes new equipment, technology and tunneling methods. So it is incumbent on tunneling professionals to constantly improve their knowledge of the profession. This is where spending a few days with other underground construction professionals can assist the tunneler in keeping up.Every two years, tunnelers and underground construction engineers, contractors, suppliers, designers and owners from around the world gather for the Rapid Excavation Tunneling Congress (RETC). The 2017 conference was held in June in San Diego, CA. The UCA of SME puts on the conference.This years’ RETC attracted 1,400 attendees. The accompanying sold-out exhibit totaled 188 service and equipment suppliers. In addition, the conference had the UCA of SME bookstore, where the new History of Tunneling in the United States book was introduced. And a short course on tunnel rehabilitation was featured.Technical programmingRETC 2017 featured nearly 100 technical presentations. Topics covered the breadth of the global underground construction industry. Here is a sampling of a few. The proceedings from the conference is available from SME, 303-948-4200, www.smenet.org.Accomplishing extraordinary tasks as a machine supplier for Metro Doha: The construction of the Metro Doha in the State of Qatar established a modern, safe, efficient and integrated public transportation network. Upon final completion of multiple phases, the network will comprise four metro lines with a length of 216 km (83 miles) and 100 stations. Phase one comprises 112 km (43 miles of underground tunnels (56 km or 22 miles of twin-tube tunnels). Twenty-one earth pressure balance tunnel boring machines (TBM) were deployed by the four different joint ventures. The project was initiated, managed and supervised by the owner, Transport Authority Qatar Rail.Phase two of the Doha Metro will start upon the completion of Phase One in 2019 (Qatar Vision 2030). The owner placed full faith in the manufacturer’s abilities to deliver equipment of high quality, state of the art standards within the given time frame. This paper focused on the manufacturer’s scope of delivery and on the supplier’s high standards of quality in production, logistics and services."

Jan 9, 2017

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011