Search Documents

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

The sixth Annual RMCMI Mine Rescue Evaluation was held during the 1997 Institute convention at Sheraton Steamboat Resort, Colorado. The Mine Rescue committee, co-chaired by Becki Boam and Gary Cook, is one of 18 committees of the Institute. In 1997 the largest number of teams participated in the program. There were nine: BHP Minerals - La Plata Mine, BHP Minerals - Navajo Coal Co., BHP Minerals - San Juan Coal Co., Bridger Coal Co., The Coteau Properties Co., General Chemical Co., The Sabine Mining Co., Solvay Minerals and Western Energy Co. Professional evaluators who provided challenging scenarios for the 80 participants were Jack Knight of Milton, Florida; Wilson Begay, Chris Saxon, and Gaylon Yazzie all of Western States Security; Mary Bailey, Bailey Associates; Tom Bass, California Department of Corrections; and Art Saenz, BDC. Seven members made up each team plus one or more trainers and represented the states of Montana, New Mexico, North Dakota, Texas and Wyoming. Ten different scenarios were presented during the two day evaluation. Each team was given the pertinent information to solve the problem as they assembled at the site. Mine Rescue families and friends participated as victims providing realistic scenarios to simulate the stress of an actual rescue incident. Each team was unaware of the circumstances until arriving at the various scenes in and around the Sheraton resort. [ ] These teams are providers of prompt rescue and medical care for accident victims at their respective properties. The members act with immediate and professional knowledge to save lives and prevent further injuries. Sponsors who contributed financially to the 1997 program are: Argo Industrial, Antelope Construction, Fisher Safety Supply, Flanders Electric Motor Service, Inc; Intermountain Electronics, Inc.; King Energy Services, Inc.; Rocky Mountain Electric Motors, LS.; TerraMatrix and Triune Inc. On Saturday evening, June 28, a reception was held for all mine rescue participants and spouses who had advance registered for this social event. The RMCMI Board of Directors was invited to attend and meet with the teams. As convention attendees, all mine rescue participants and registered families attended the Monday night country western reception and Bar-B-Q. This was followed by an adult western melodrama. [ ] Glass awards with the RMCMI logo and a Mine Rescue figure were presented at the Tuesday Mine Rescue buffet breakfast to all nine teams, each of which had achieved proficiency at level 3. Captains of the teams pictured below are (from left standing): Ron Neff, BHP-San Juan; Ted Laughline, Bridger, Terry Davis, Coteau; Jim Knutson, General Chemical (from left kneeling): Dan Allerdings, Rosebud; Ron Miller, BHP-Navajo; Jonathan Sorrell, BHP-La Plata and Ray Blaisdell, Solvay. Gary Cook is to be commended for his solo last minute supervision of the Mine Rescue program, due to Becki Beam's unavoidable absence. The teams look forward to the 1998 convention at Snowmass Village Resort, Colorado Thursday and Friday, June 25 and 26.

Jan 1, 1997

By Will H. Coghill, F. D. DeVaney

"Many of the iron ore deposits on the western end of the Mesabi Range Minnesota consist of the so-called ''wash ores."" Because of their high silica content these ores must be washed or concentrated to make them merchantable. Washing plants have been in operation for 20 years, during this period large quantities of tailings have accumulated in tailings ponds. These tailings contain the aggregate millions of tons of iron oxides which, if recovered, would greatly to the available tonnages and to the revenues of the mining companies. It the purpose of this paper to outline give results of concentration tests on tailings.In order that the reader may understand more clearly the type of material under consideration, a short description of the characteristics of the wash ores of the Western Mesabi Range and a brief resume a washing methods that have been are now being employed will be given. Appleby and Newton4 In their description of the district and of the ores say:The Western Mesabi district embraces the territory west of the town of Nashwauk in Itasca County. The territory to the east of this dividing line is known as the Central and Eastern Mesabi district. This subdivision is rot wholly arbitrary. While the ore bodies in the two districts resemble each other in. shape, size, and general structure, there is a marked and very important difference in the character of the respective ores. For purposes of comparison, the western deposits have been called washable ore bodies, and the central and eastern, standard ore bodies. The latter ores are the result of natural concentration processes which have teen carried far enough to produce a large proportion of high-grade ore Wet can be marketed direct; the Western Mesabi ores present a lesser degree of natural concentration and are as a rule of too low grade to admit of marketing without preliminary treatment. In many cases the grade can be improved by washing, hence the material is called washable ore. Exceptions to thin general rule may be noted in both districts. Many of the Western Mesabi ore bodies contain quite a proportion of merchantable ore. There are also portions of central and eastern Mesabi ore deposits which are of low grade and which can be improved by washing."

Nov 1, 1930

By D. J. Droppert

This paper describes the precipitation-production of crystalline scorodite (FeAs04.2H20) from arsenic-rich sulphate-based metallurgical solutions at ambient pressure (95°C). Arsenic is precipitated by means of a controlled precipitation technique in which the supersaturation of the solution is carefully controlled. By controlling the supersaturation in the presence of seed material. the formation of amorphous ferric arsenate is prevented. Scorodite is known to be the most stable As(V) compound and is therefore preferred as host mineral for arsenic immobilization. The effect of the following parameters on the preCipitation behaviour and kinetics of scorodite are discussed: Type of base seed concentration initial [As]. sulphate concentration. neutralization rate. seed recycling and method of Fe(ll!) addition to Fe-deficient arsenic solutions.

Jan 1, 1996

By W. B. Tucker

UNUSUAL interest has recently centered in the Mojave mining district of California, owing to new discoveries of gold ore at the Silver Queen mine, and subsequently at other neighboring proper- ties. These finds have proved that opportunities exist for the prospector even in old mining districts, where careful search may still be rewarded. The Mojave district is characterized by a group of small hills centering around Soledad Butte, four to six miles southwest of Mojave, in Kern County. This butte is 1250 ft. higher than the surrounding desert and 4000 ft. above sea level. Four miles west of Soledad Mountain are the so-called Middle Buttes, a group of flat-topped hills. Gold was first discovered in the district in 1894, and the following productive mines developed: Queen

Jan 1, 1936

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By D. G. Hattingh, A Els-Botes

"Considerable information is available on the factors influencing the iron-zinc reaction rate at 450° C of low carbon steels, in comparison there is a scarcity _of similar fundamental information of spheroidal graphite irons. This can be attributed to the more complex microstructure and ferrous alloy chemical analysis of spheroidal graphite irons. Hot-dip galvanizers have identified the complexity in controlling and predicting the thickness of the galvanized coating formed on commercial cast irons, which has serious financial implications for both the galvanizer and customer.Commercial hot-dip galvanizing has been in use for over 160 years and yet an elementary understanding of the dynamics associated with the hot-dip galvanizing of spheroidal graphite cast iron is still insufficient. To allow the. process to become a modem surface engineering technology, the fundamental aspects of the process must be thoroughly understood.When a clean iron or steel article is dipped into the molten zinc, zinc initially solidifies around the steel or iron. As heat is transferred to the article form the bath, this initial solidified zinc layer remelts and a series of iron-zinc alloy is formed by the reaction of the zinc with the surface of the article; on removal from the bath, some of the molten zinc is taken out on top of the alloy layers. At normal galvanizing temperature (450 °C), the reaction between iron and zinc is usually parabolic with time. The rate of reaction is rapid at first but then slows down and the coating thickness does not increase greatly if the article is immersed in the bath for longer times(1)."

Jan 1, 2000

By W. H. Adams

Shortly after becoming one of the van-guard of mine-developers in the State of Virginia, during the year 1883, I called the attention of the Institute to certain deposits of pyrites, which have been largely worked since. In all cases these deposits are covered with iron-ore (limonite), extending 40, 50 or 60 feet from surface to water-level. The several classes of brown iron-ores are found almost continuously along a prominent ridge of mineral-bearing slates, which can be traced from the James river northeasterly to the North Anna, the Rappahannock and the Potomac rivers, crossing the counties of Louisa, Spottsylvania and Stafford. Outcrops are plainly discoverable from end to end of this belt, also, in places, to the right and left of it, and at intervals there are evidences of workings, some of them for known purposes and others of unknown age and meaning. These old workings have an interest aside from the minerals they may contain or may have yielded. I have been engaged during the past five years in the collection of facts concerning them, which might determine definitely the site of those iron-furnaces, placed by tradition within reach of " the towne called Germanna," which were the first ever built in this State or on this continent. The events which led to the establishment of this important industry are sufficiently narrated in a paper written by Mr. R. A. Brock, Secretary of the Virginia Historical Society, and printed in the Proceedings of the National Museum, 1885, page 77, from which I quote the following : " To Virginia, the first of the English settlements in America, belongs the honor of inaugurating within her limits, as a colony, that most important industry, iron manufacture. "The London Company contemplated a variety of manufacturing enterprises from the very beginning of its authority; prominent among them was that of iron. In 1610 Sir Thomas Gates testified before the council of the Company at London, that in Virginia &apos; there were divers minerals, especially iron-oare,&apos; lying upon the

Jan 1, 1892

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Charles D. Litton

This U.S. Bureau of Mines report describes the results of two large-scale tests conducted to evaluate a prototype nitric oxide (NO)-compensated carbon monoxide (CO) fire sensor, developed by Carnegie Mellon Research Institute (CMRI). In the tests, small coal fires were allowed to develop in the presence of diesel exhaust at relatively low ventilation airflows. These tests compared the response of the CMRI fire sensor with that of other fire sensors, including the Bureau&apos;s diesel-discriminating smoke detector. During the tests, CO, NO, and smoke levels were continuously monitored in order to determine the sensor alarm times and gas levels as the fire developed. The data indicated that the NO-compensated CO fire sensor was capable of suppressing the CO produced by a diesel engine and that the sensor responded reliably to the CO produced from the test fires. The tests also showed that the Bureau&apos;s diesel-discriminating smoke detector alarmed earlier than the prototype NO-compensated CO fire sensor.

Jan 1, 1993

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By P. LEROY FOSTER

G EOPHYSICAL prospecting was presented in its several aspects and discussed with much vigor at two sessions during this year&apos;s annual meeting of the Institute. The first session was devoted entirely to the presentation and discussion of various technical papers, while the second meeting took the form of a round table conference on the advisability of revising the existing mining laws to recognize the results of geophysical prospecting. This conference was immediately followed by further consideration of technical papers. Each session was well attended and great interest was displayed by everyone present.

Jan 1, 1929

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

A new porphyry copper gold district has been discovered at Goonumbla near Parkes in central New South Wales. Endeavour 26 North is the largest deposit known to date with a possible resource of 166.4 million tonnes at 0.74% copper, 0.12g/tonne gold and 1.7g/tonne silver, using a cut-off grade 0.3% copper. Mineralisation is primarily bornite in the higher grade zones and chalcopyrite in the peripheral lower grade zones. Most of the copper, gold mineralisation is associated with potassic alteration. Two mineralised quartz monzonite porphyry intrusive stages have been identified and these are related at depth to a large monz- onite stock which may have been the source of some of the mineralisation. On the basis of detailed paragenesis studies, the potassic zone can be divided into three symmetric subzones. The low grade inner potassium feldspar subzone is confined to the later intrusive porphyry. The outer potassium feldspar subzone is the most highly mineralised alteration halo due to the focussed superimposition of two hydrothermal cycles which have overprinted intrusive and volcanic rocks. The fringing biotite potassium feldspar subzone reveals alteration minerals which are developed early in the paragenesis. Fracture controlled quartz sericite alteration with low sulphide content, fringes and, in part overprints the potassic zone. The restricted pipe-like nature of the alteration zones and related mineralisation suggests that Endeavour 26 North is repres- entative of a multiphase focussed porphyry copper gold system.

Jan 1, 1986