Search Documents

By R. D. Leitch

"The pollution of streams has received much attention during the last few years, and although there are many other and more serious forms of pollution, the problem of acid mine drainage is important in certain sections of the country, particularly in Pennsylvania. At the request of the United States Public Health Service the Bureau of Mines undertook to determine some of the factors contributing to formation of acid mine waters, the yearly variations in quantity and quality of drainage, effect of mining methods, and various other questions arising in connection with the problem; some attention was also given to its economic phases.In acknowledgment, the writer wishes to thank Dr. R. R. Sayers, Chief surgeon; A. C. Fieldner, chief chemist; and W. P. Yant, supervising chemist, health laboratory section of the Pittsburgh Experiment Station, all of the Bureau of Mines, under whose direction the work was conducted.Because no data of a like nature had previously been determined, and with the thought that such data would throw additional light on the general subject, a stream having a number of mines draining into it was selected for observation in both high-sulphur and low-sulphur bituminous-coal districts, as designated in commercial rating. These mines and streams were visited in both wet and dry seasons to note the quantity and variations in acidity of mine drainage and the subsequent effect on streams. Maps of these streams with the sampling points are shown in Figures 1 and 2. In a report of this nature a great deal of tabular data is best emitted, but reference to the maps will serve to indicate the factors that determined sampling points, such as tributary streams and gobs."

Sep 1, 1928

By Stephen D. Cramer

A nondestructive procedure for measuring electrodeposit porosity has been developed which records the location and number of deposit defects including pores, pits, and voids. The procedure involves the passage of an X-ray beam through the deposit-substrate system onto suitable film. The defects are recorded as images on the film. Variables studied included intensity and spectra of the X-ray beam, composition and thickness of deposit and substrate, film type and developing procedure, and limits for detecting defects. At an X-ray tube voltage of 40 kv, pores several mils thick were easily detected in copper-nickel specimens more than 20 mils thick. To illustrate the utility of the procedure, the effect of substrate oxidation and of current density on electrodeposit porosity was briefly studied.

Jan 1, 1970

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By César Sotillo

"El presente texto describe el proceso de la industria del acero en México. La compañía fue fundada en el siglo XX y tiene sus altos hornos en Monterrey, capital del estado Nuevo León, donde se funden los minerales de fierro que provienen de los yacimientos del Cerro de Mercado, situado en la región central de Durango. El yacimiento consiste de cuerpos inclinados hacia el oeste y que tienen contactos bien definidos con la roca encajonante; Asimismo afloran cuatro cuerpos de mineral, de los cuales el más grande tiene cerca de 800 metros de longitud. El cuerpo mineral está dividido en dos partes por resbalamientos producidos por fallas en la porción occidental del valle; los mismos que junto con la erosión, han producido la peculiar topografía de esta parte del estado de Durango. "

May 1, 1953

By Alfred Goldberg

The paper is founded on the results of an investigation on the softening behavior of a cold-rolled low carbon steel. This specimen, originally cold rolled 15 , 30 , 50 and 75% reduction in thickness, were annealed at several temperatures ranging from 481 to 687ªC. A temperature-time range was encountered over which strong competition between these processes was evident. An interpretation on the effect of test variable on determining which one of the competing processes dominated during annealing is presented.

Jul 20, 1961

By R. L. Rankin

The program objective was to conduct surveys of respirable dust concentrations in coal mining operations at locations outby the working face. The results of these surveys were directed toward 1. identifying outby dust sources, 2. evaluating the severity of the major dust sources, 3. establishing dust sampling frequency, 4. establishing dust sampler locations, and 5. assessing the? areas of influence of the dust sources. The study included dust sampling of only nonhigh risk personnel and areas at six dif-ferent mines. Thirteen continuous mining, four longwall and two conventional mining sections were sampled. The severity of outby respirable dust sources such as load points, runways, dump points, beltways, transfer points and main haulage operations were characterized and areas within the mine were ranked according to severity. Information on engineering controls was also acquired. Guidelines for implementing a dust sampling program are presented and include sampler locations, ventilation surveys, dust surveys, effects of shift-to-shift variations, and sampling frequency.

Jan 1, 1980

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By Hong Yong Sohn, Miguel Olivas-Martinez, Zhixue Yuan

A novel flash ironmaking process that directly reduces iron oxide concentrate particles by gas is under development. The goal of this work was to study the possibility of reoxidation of iron particles in various gas mixtures. As the product iron cools down in the lower part of the flash reactor, conditions may become favorable for reoxidation because of equilibrium and high reactivity of iron particles. The effects of temperature (823 – 973 K) and H2O partial pressure (40 – 100 pct., Ptotal = 86.1 kPa) on the reoxidation rate were examined. The pressure dependence was first order with respect to water vapor, and the activation energy was 146 kJ/mol. A complete rate equation that adequately represents the experimental data was developed. For oxidation in O2-N2 mixtures, the effects of temperature (673 – 873 K) and O2 partial pressure (5 – 21 pct., Ptotal = 86.1 kPa) were determined. Reoxidation in pure CO2 was also investigated at 873 – 1073 K for comparison.

Jan 1, 2014

By Greg Ford

Each year, companies spend millions of dollars on safety training and on safe equipment, money that is generally well spent. Despite that, we still make mistakes. What happens if the mistakes are made not because of inadequate training, but because we are hard-wired to act in a certain way? If you read any of the ?Because of Human Error? text boxes in this document, situations like these may look familiar in your own workplace. ?The issues of risk, health, safety and the environment are getting more attention now than ever before, at all levels of the organization,? said Calvin Price, vice president of Global Health and Safety at LNC-Lavalin Inc., a company with 21,000 workers worldwide. Most would agree with Price that attention to safety is increasing because responsible companies care about their workers and the workers? colleagues, families and communities. However, cynics might say that the safety spotlight is powered by the corporate bottom line. Direct costs created by workplace injuries total $51.8 billion annually and include workers? compensation payments, medical expenses, civil liability damages and litigation expenses. This sum represents a staggering one quarter of each dollar of pretax corporate profits. Indirect costs may run as much as 20 times the direct costs of on-the-job accidents and illnesses. Examples of indirect costs include training replacement employees, investigating the accident and implementing corrective measures, lost productivity, repairing damaged equipment and property, and costs associated with lower employee morale and absenteeism. What?s interesting is that up to 90 percent of incidents are due to human error, not faulty equipment or other factors.

Aug 1, 2013

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021

By C. W. Goodale

I. INTRODUCTION. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and -is this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 8, 1913

By Don Steffa

Drift mining, according to California mining terminology - and it is distinctly a California development - is the blocking out and extraction (breasting) of the auriferous gravels of an ancient buried stream either through tunnels, inclines, or shafts; it is one of the minor divisions of the larger classification known as placer mining. The contribution of each of these divisions and of lode mining to the gross production of gold in California totals as follows:3 [ ] The total amount of gold recovered from the placers of California from 1848, when Marshall discovered the precious metal in the mill race at Coloma, to 1928, was $1,226,515,404. The same period saw a total gold production from all operations of $1,823,562,360.

Jan 1, 1932