Search Documents

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Rambabu Pothina, MELO EDUARDO PIMENTA DE, Rajive Ganguli

 The mining industry is home to a mass of sensor-generated data that are critical to real-time and long-term optimization. This heavy reliance on sensor data has resulted in an undesirable development. The industry is reluctant to verify the accuracy of sensors as it would mean shutting down important processes. Sensors are typically calibrated once a year, if at all. Errors in sensors go undetected until the next calibration or until errors are so gross as to be obvious

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By L. K. Smith, C. R. May, K. R. Schrag, H. Buchwald

"New contracts for 65 million long tons of coking coal valued at over $900 million, over the next 15 years, herald the rebirth of Alberta's coal industry. The industry is optimistic that export orders may reach 20 million tons per annum by the mid-1970's. Coal will be extracted from underground and surface mines and it is expected that the total labour force will double from the present 1,200 men within the next two years. Ali the health hazards associated with coal mining are likely to be encountered and it will be incombent on the Provincial Department of Health to specify the standards which relate to health and environment where no such standards have previously existed. This paper examines some of the problems which are being encountered in setting up an environmental health program and reviews the practicability of environmental monitoring methods, with special reference to respirable dust."

Jan 1, 1969

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By Charles W. Frey

COMPRESSED air is one of the most useful tools that the mine operator has at his disposal. It is clean, nontoxic, easily handled, and can be distributed anywhere that a man can drag a length of rubber hose. Without it a great deal of drilling would still be a laborious hand process, and although the John Henry of legendary fame could beat a mechanical drill, John Henrys are few and far between, and in the long run the air drill is the victor. As a general rule, horizontal compressors are lubricated by mechanical lubricators, which furnish oil to the cylinder walls, whereas vertical units are splash lubricated. In most horizontal machines oil is introduced at the top center of the piston, from which point it can run down and lubricate the rest of the piston. Some large units introduce oil at more than one point on the cylinder wall, the necessity for this and the number of points of introduction depending upon the size of the cylinder.

Jan 1, 1938

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By E. Mata Robles

El presente texto refiere el proceso historiográfico de la planta concentradora Mahr Túnel ubicada en el valle del río Yauli a 3.4 kilómetros de las coordenadas de la carretera central del Perú. La planta se construyó en 1937 para el tratamiento de los minerales de plomo, cobre, zinc de la mina San Cristóbal. La operación de la planta comprende: recibo del mineral, planta de chancado, circuito de molienda, flotación Bulk cobre- plomo, flotación de zinc, espesamiento y flitrado, disposición de relaves. Los datos estadísticos de la planta se basaron en la capacidad, número de obreros, número de empleados, fuerza eléctrica, consumo de barras y bolas y consumo de reactivos. La seguridad y higiene de la planta concentradora mencionada cuenta con un Comité de seguridad conformado por un Superintendente de campo, ingeniero de Seguridad y el médico de campamento, así como para casos de accidentes es suministrado por el Hospital de Mahr Túnel.

Aug 20, 1963

By W. M. Tupper

[The two types of sulfide deposits in the Bathhurst Newcastle area are; (a) epignetic fissure deposits, and (b) massive sulfide deposits. Geological evidence has been variously interpreted to suggest a syngenetic origin, a source bed' origin, or a magmatic hydrothermal origin for the massive sulfide deposits. Sulfides disseminated through the black shales and argillites of the host rocks are enriched in S32 (mean value 22.34, S34. = 5.8 per mil) relative to the meteoritic standard of 22.21, and have a broad spread in range of values. S32/S34 ratios of sulfide minerals from the deposits occur in two distinct groups. The massive sulfide deposits exhibit ratios between 21.88 to 22.05, while the fissure deposits exhibit ratios between 22.18 and 22.21. These results suggest two separate sources for the sulfur, each, however, resulting in magmatic hydrthermal deposition because of the narrow spread of ratios in each group. Granite intrusive into the host rocks of the sulfide deposits have a mean K/A age of 386 ± 10 M.Y. Lead minerals in the sulfide deposits have a mean nodel lead age of 370±20 M. Y. Thus the lead minerals and the granite bodies were emplaced during the same major orogenic event. Sulfide minerals from magmatic hydrothermal deposit have a very narrow range of S32/S34 values, as do those of the Bathurst area. It seems reasonable, therefore, that well homogenized magmatic hydrothermal solutions are the most logical source of the sulfide deposits. Furthermore, the homogeneity of the lead isotopic abundance data gives strong independent evidence that the ores are of a magmatic hydrothermal origin.]

Jan 1, 1960

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942