Search Documents

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By R. N. Roby

In the course of the Bureau of Mines investigations for suitable sources of high-aluminum clay for the production of alumina, the Whiteware clay deposit was examined in August 1942 by G.N. Bennett, mining engineer, Bureau of Mines, Montana District Office. This report presents the factual data obtained by the investigation, which also includes data on trenching and drilling, and the results of some refractory tests and chemical analyses of representative samples of the clay later taken from some of the best trench exposures and from adit dumps.

Jan 1, 1949

By NA NA

Listing safety award winners, £I43M has been added to proceeds from coal privatisation in the year to March 1997, bringing total revenues to over £1.3bn, some company news in brief.

Jan 8, 1997

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By Masaru Tomoguchi, Tom Nishiyama, Naoto Sasamoto

"In Hanaoka Mine, which was one of the major ""black ore"" (Kuroko) mines in the north part of Japan, mining has finished in 1994, and only mineral processing plant is available now. Recently this mineral processing plant has been applied to the soil washing. Soils contaminated with heavy metals are excavated and transported to the plant. The soils are separated to cleaned soil and metal enrichment through the process which consists of scrubbing, classification, extraction, insolubilization, flotation, and so on. The process is flexibly designed for each contaminated soil, in order to the products can be recycled as cleaned soils or metal sources. . Soils contaminated with arsenic and lead were treated in 1999, which were entrusted from Environmental Agency of Japan.IntroductionDowa Mining has had the mine site named ""Hanaoka Mine"" and ""Kosaka Mine"" in the north part of Japan. Those mines consisted of some ore deposits and produced ""black ore"" (Kuroko) and ""yellow ore"" (Oko), which are complex sulfide ore. The ""black ore"" mainly consists of sphalerite, galena and barite with accessory chalcopyrite, tetrahedrite and Au, Ag minerals. The ""yellow ore"" mainly consists of powdery and clayey ore containing chalcopyrite and. pyrite, with a little sphalerite and galena. Each mine site had mineral processing plant respectively, ""Hanaoka Mine"" had two and ""Kosaka Mine"" had one plant. Those plants were operated by flotation process to separate each mineral, and produced concentrates of copper, lead, zinc, pyrite, barite and so on.Unfortunately, the mine had closed one by one because of change in economical circumstances and the lack of ore reserves. Mill plants were also closed and dismantled, but the last ""Matsumine mill plant"" of Hanaoka Mine was remained to be utilized usefully. In the circumstance like that, we came across with soil remediation business. Recent reports say that subsurface contamination in Japan is being grown substantially and that it can be a serious matter beyond the imagination of our society. So nowadays we have a tendency to pay attention to the environmental issues including subsurface one."

Jan 1, 2000

By ALEX. S. THOMAS

HOWEVER good a furnace may be in regard to design, etc., or however excellent in the quality of the gas used, a suitable heat for the successful working of the metal cannot be obtained unless the melt be coated with a proper quantity of slag. This coating may be excessive or it may be deficient in quantity. The right degree of heat is the essential condition of successful working, for the quality of the steel made is never very good when the metal is allowed to simmer in the furnace for an excessive period, and this heat cannot be obtained if the metal is not protected by a proper covering of slag. This is not only to prevent the metal being over-oxidized and wasted, but also to prevent the metal being chilled when exposed with only a thin covering of slag. The slag may be obtained in either of two ways : 1, naturally, by the presence of sufficient silicon in the iron used, to unite with iron oxide to form a staple slag ; or, 2, by the addition of slag or free silica. In the first case the slag is formed naturally by the action of the oxygen in the flame - i.e., the oxidizing atmosphere of the furnace-on the silicon in the metal when melting. The charge then melts, as it is termed, "thick," and protects the banks from being cut. If too much silicon be present, however, and an excessive quantity of slag be formed, it will be found to be rather infusible, and unless care be taken to add the oxides quickly and follow the furnace up-thus rendering the slag more fusible by the extra iron oxide-the furnace bottom is liable to be pulled up. In such cases the author has frequently been able to warn

Nov 1, 1906

By Diógenes Uceda Herrera

La refinería de cobre en Ilo, procesa el cobre ampolloso que proviene de la fundición de Southern Perú Cooper Corporation, la cual trata los concentrados cupríferos de las minas de Toquepala y Cuajone. En este proceso, el cobre ampolloso se vuelve pre-refinado a través del fuego para así eliminar algunas impurezas y moldear los ánodos de cobre. Posteriormente en la electrólisis, este cobre de ánodo se deposita en el cátodo, liberándose los demás elementos para constituirse en lodos anódicos y así luego ser lixiados con ácidos para recuperar el cobre y centrifugados completamente. En este sentido, el texto señala el método de tostación oxidante con Na2CO3 y en agua como uno de los que más se adecúa a la composición química particular de los lodos anódicos de esta refinería.

Nov 20, 1978

By Yu Chuang, Zai Jinmin, Liu Songyu

"The piled raft foundation is a geotechnical composite construction method, consisting of three elements, piles, raft and soils, which is applied for the foundation in an increasing number. Differential settlements have numerous negative effects on a superstructure in piled raft foundations. Through the analysis of the production mechanism of differential settlements and differential settlements control measures, a method of adjusting pile configurations is presented to control differential settlements. By comparing the measured data and finite element method analysis of one oil storage piled raft foundation, the new method is verified that the differential settlements can be reduced effectively and the inner forces of foundations are more reasonable with varying length pile configurations. The differential settlements can be minimized or even reduced to zero with right pile length.INTRODUCTIONPiled raft foundations are widely adopted for the prominent advantage of limited settlements and adequate bearing capacities. However, there always exits differential settlements in conventional piled raft foundations. The differential settlement is the main cause that produces additional stresses in the structure. Differential settlements have numerous negative effects on a superstructure as well as on a foundation, and should be restricted to allowable limits. How to control the differential settlement is the key interest.An increasing number of structures are founded on piled rafts. For this reason, design strategies that enable an optimized design have a major importance for safety and economy. An optimized design may be defined as a design achieving maximum economy of the solution, that is minimum cost for the installation of the foundation."

Jan 1, 2005

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By R. H. Sprute

This report describes a feasibility study to consolidate coal waste sludge in a 100-acre pond by applying direct current between floating and buried electrodes. The study was conducted by the Bureau of Mines under a cooperative agreement with Washington Irrigation and Development Co., located near Centralia, Wash. Part 1 covers results of laboratory tests at the Bureau's Spokane Research Center and a small-scale field test at the cooperator's coal preparation plant in western Washington. The process is efficient and cost-effective when power is applied at low current density. A proposed system, fully described in part 2, has electrodes covering 21 acres of pond surface radially arranged around a central power platform. Densification of pond contents would require 2 to 3 years of treatment. Total cost of equipment, labor, and material is approximately $500,000.

Jan 1, 1982

By Elmer Vidal Sánchez

Dado que la voladura de rocas en minería y construcción genera vibraciones de terreno, ocasionando daños a las instalaciones cercanas a la operación, se ha visto necesario realizar un control de las vibraciones por medio del criterio de velocidad pico de partículas. De acuerdo a este criterio, para toda voladura existe una mínima cantidad de explosivos a detonar dentro de un intervalo de 8 milisegundos. Sin embargo, no considera la variable "frecuencia" como parte del control de vibraciones. En este sentido, el presente texto describe una alternativa diferente para el control de las vibraciones denominada "análisis de frecuencias", cuya técnica se basa en un modelo computarizado que controla y predice las vibraciones en un lugar específico, considerando las condiciones geológicas existentes entre el lugar de la voladura y el punto de interés.

Aug 26, 1988

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By Cajsa Samuelsson, Theo Lehner

Converting and refining play a central role in the extraction of metals. Sweden has a long tradition as an experimental play ground for metallurgists, chemists and alchemists, developing new methods and technologies. Presenters of papers are usually happy in recording successful developments. But reporting failures can be as great a value as the former. In the paper experiments and experience in process development are illustrated, differences between ferrous and non-ferrous developments are highlighted and industrial learning curves are discussed. 53

Jan 1, 2009