Search Documents

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972

By José Fernandes De Oliveira Ugarte

El presente texto tiene como objetivo la evaluación del oro nativo y electrum encontrado en su forma libre, diseminado, encapsulado en matrices sulfurosas y sulfatadas que fue empleado en los procesos de flotación y lixiviación. Para ello, se estudiaron 54 muestras que fueron analizadas por difracción de rayos X y clasificadas en tres grupos con 18 muestras cada uno e identificadas de matrices oxidada, sulfatada y sulfurosa. Después de tamizadas fueron colocadas en briquetas de 4 mm de diámetro y analizadas por microscopía electrónica para los estudios estadísticos de los minerales portadores de oro y para los estudios de microscopía óptica.

Nov 1, 2015

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By William Gleason

The mining industry is a unique space. It is one in which geologists and chemists can intersect with computer and data science professionals daily. The industry requires expertise in not just mining and metallurgical engineering, but also electrical, mechanical, environmental and more. It requires expertise in worker health and safety, behavioral science, finance and economics, as well as human resources management. The locations of mining operations are often in remote corners, and for underground activities, they are unlike anything else in the world. The industry presents those who join it a wealth of opportunities, but often struggles to overcome incorrect perceptions of safety, labor and environmental standards, making it difficult to recruit and retain employees at a time of increased demand for mined materials.

Dec 1, 2025

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978

By Jürgen Kretschmann, Christina Suarez, Jürgen Brune, Stefan Möllerherm

"The Ruhr region in Germany’s North-Rhine Westphalia is going through significant change. By the end of 2018, the last two underground hard coal mines in the Ruhr, Ibbenbüren and Prosper-Haniel collieries, will close their portals and bring an end to more than 200 years of coal mining and an industry that was once the economic and cultural backbone of the area. Ruhr is undergoing an impressive economic and cultural transformation, as it gradually shifts from being a region once dependent on coal and steelmaking to a post-mining region focused on redesigning itself as a cultural center. This article focuses on the socioeconomic impacts of the transformation into post-mining and the roles of the government, labor unions and local community to aid the transformation from the perspective of an American student. It will look into the cultural values that are helping to drive the transformation and compare them to American standards and values in order to determine if a similar approach can be used in the United States and its coal industry. History and backgroundUnderground hard coal mining has had a long history and a significant impact on the culture and economy in Ruhr since the early 19th 20century. The Ruhr region is located in the heart of the German state of North- Rhine Westphalia. Ruhr is bounded by the Rhine River in the west, the Ruhr River in the south and the Lippe River in the north, with the Emscher River running through its center.The Ruhr is home to around 5.1 million people and spans an area of approximately 4,500 km2 (1,730 sq miles). Before the era of industrialization, the Ruhr was a rural, agricultural region. Small-scale coal mining began in the 13th century, with coal being used for heating, cooking and metallurgical processes, including steelmaking. With 19th-century industrialization, coal mining became a significant driver of the region’s economic structure. Steam engines, and soon, electric motors, allowed for the pumping of mine water and for powerful hoists hauling from deep shafts, enabling miners to reach deeper coal seams that were once thought impossible to mine. The Ruhr mining boom began in the 1850s, supported by Prussian economic policies that attracted many workers and their families to the region. The population grew from 400,000 in 1850 to 5.7 million in 1957. The coal and steel industries were key contributors to Germany’s “Wirtschaftswunder” — or “miraculous economic recovery”— in the 1950s. In 1956, the coal industry reached its peak production of around 112 Mt/a (124 million stpy) of coal and employed almost 600,000 miners."

Mar 1, 2019

According to the Darcy?s law, filtration rate should increase with increasing pressure drop (?P) across a filter cake. In centrifugal filtration, ?P is created by the free water present on the surface of a filter cake. Thus, ?P can become negative when the free water disappears from the cake surface, which makes it difficult to achieve low cake moistures. In the present work, we have developed methods of overcoming this problem by either increasing the air pressure inside or applying vacuum outside a centrifuge. Laboratory dewatering tests conducted using these provisions showed that the moistures of various minerals and coal fines can be reduced to the level that can obviate the need for thermal drying. The new concept has been successfully tested both at pilot- and full-scale, which lead to commercial deployment through Decanter Machine, Inc., under the trade name Centribaric® centrifuge. Keywords: dewatering, hyperbaric centrifuge, pressure drop, Darcy?s law, Centribaric® centrifuge

Sep 1, 2012

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By G. W. Reimers

Conditions in the underground mine environment can cause self-heating of sulfide ores as a result of exothermic oxidation reactions, which may result in mine fires. This Bureau of Mines report describes thermal analyses of finely ground chalcopyrite, chalcocite, galena, pyrrhotite, marcasite, and arsenopyrite, to characterize their responses under oxidizing conditions. Thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) were used, in the temperature range 1000 to 5000 C. Chalcopyrite showed an initial weight gain, due to formation of sul-fates, a weight loss, caused by ignition of iron sulfide to iron oxide, and a final weight gain, indicating the conversion of copper sulfide to sulfate. Chalcocite did not ignite in the temperature range studied but exhibited a rapid weight gain, because of the rapid conversion of copper sulfide to sulfate. Likewise, galena failed to ignite but underwent a steady weight gain when oxidized in a moist atmosphere, showing conver-sion of lead sulfide to sulfate below the ignition point. Marcasite underwent a rapid weight loss, indicating ignition, at 2000 C. Moisture in the oxidizing atmosphere lowered the ignition point of marcasite and arsenopyrite but not that of pyrrhotite. All the sulfides exhibited exothermic behavior at temperatures below the ignition point.

Jan 1, 1987

By Kaixi Jiang, Chaozhen Zheng, Shuchen Qin, Hao Ma, Yufang Wang

The study investigates the behaviors of zinc and iron in neutralized residue during pressure and hot acid leaching. It examines the effects of temperature, acidity, leaching time, and oxygen partial pressure on zinc extraction. The results indicate that the acid to zinc mole ratio is crucial for the extraction process, with a zinc extraction rate reaching 98.0% under optimal conditions.

Feb 14, 2022

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

By A. D. Davis, C. J. Webb

Brohm Mining Company's Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February of 1999 the Governor of South Dakota announced plans to request the U.S. Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable ground-water reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2002

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By C. R. Royal, B. E. Friedland

Energy & Densification Systems (EDS) has developed patented new technology crushing/milling equipment. The EDS Multishaft Mill is a compact vertical mill – utilising high-speed impacts to break down particles with large reduction ratios, low energy consumption and improved liberation. The milling action combines several processes to provide a multitude of output products to satisfy various specifications. Comminution often accounts for more than 60% of the total power consumption on a mine. Two of the key problems to be solved in comminution is to bring down the specific energy required to reduce particle sizes; and to improve liberation or improve the efficiency of the beneficiation and recovery of the required elements. The EDS Mill has shown extensive improvements in both these areas with energy efficiencies up to 75% better than conventional milling equipment and improving liberation beyond the standard beneficiation processes. Conventional comminution equipment requires massive, heavy parts to be moved or rotated, consuming a lot of energy in doing so and not inputting that energy into the breakage of particles. In the EDS Mill, ramping up the relatively small shafts to speed is all that is required. Once at speed, the momentum, together with the minimal amount of constant drive required, means that the energy can be transmitted directly and efficiently into breaking down the particles. The high-speed impacts allow for a shattering effect of the particles and this quickly generates a high ratio of fines. Furthermore, the single impact force breaks particles in a very different manner to conventional compressive force breakage. With compressive force breakage, the particle breaks from point to point. With high-speed impact force breakage, the force tends to migrate through the weakest areas of the particle, which tend to be the mineral boundaries. This, therefore, means that when the particles break, the various minerals are exposed and hence liberated. Keywords: Comminution, high-speed impact, liberation, energy efficiency, novel comminution

Jan 1, 2020

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958