Search Documents

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

By Estanislao Dunin

Aunque el Perú disponga de un potencial carbonífero suficiente, no ha logrado posicionarse como principal productor de carbón. Dicha crisis es atribuida al fracaso gubernamental en el manejo de difusión y gestión del carbón peruano. Por ello, el presente texto analiza este problema a través de la tenencia de yacimientos de carbón, entidades nacionales relacionadas con el carbón y así buscar un adecuado fomento de la minería en el carbón.

Nov 1, 1982

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By Winton J. Gale

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the leading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By G. E. McElroy

As one phase of a general program of enthracite mine-fire research initiated by the Bureau of Mines in September 1935, a study of the records of past fires was considered a necessary approach to a proper understanding of present and future fires because only limited information could be obtained directly from existing active fires on account of their inaccessibility. Through the courtesy of interested operators, all available records of fires that had occurred in a large group of steep-pitch anthracite mines in the Western Middle and Southern fields of the Pennsylvania anthracite district were examined and analyzed for data on the causes, costs, behavior, and control of fires, and this report is primarily a discussion of these factors based on a close study of these particular records. Mining Conditions The records pertain to a group of mines that have contributed about 12 percent of the total Pennsylvania anthracite production and constitute a large proportion of, and well represent, steep-pitch operations in this district. Throughout the area represented, the coal occurs as a series of up to 20 parallel seams in folded slate and sandstone strata and almost entirely on pitches of 400 to 80°, with vein thicknesses of 5 to 60 feet. Practically all are old mines with histories dating back to 1850, or thereabouts, and present operations are either under or adjacent to mined-out areas extending to surface or to the saddles of anticlines. All operations are at relatively shallow depths, that is, within 1,000 feet, vertically, of the surface. Mining methods are largely a heritage of the past and embrace typical breast and pillar operations with practically no mechanized mining and with the coal shot ?off the solid.? Most of the mines are rated as gassy and are operated now on a closed-light basis. Permissible explosives are now used entirely for breaking coal, and dynamites for rock work and chute-starting blasting.

Jan 1, 1938

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Rich Perry

HARRY HINDS: Our second speaker today is Rich Perry. Rich is the manager of leach and dewatering at Newmont Gold Company's Carlin operations. He has been the operator of Newmont's refractory leach development program for the past three years. Prior to joining Newmont in 1994, he was plant superintendent at the Big Springs and Jerritt Canyon Roasting Mills for Independence Mining Company. He graduated from the University of Nevada's Mackay School of Mines, and has lived with his wife and three children in Elko, Nevada, for the past 12 years. Please welcome Rich as he presents "New Facility Design Engineering: On-Site Versus Engineering Companies' Offices." RICH PERRY: Newmont Gold Company has been mining and processing gold ore at its Carlin, Nevada, operations since 1965. Processing is done using oxide milling, heap leaching, and whole ore roasting methods. Newmont began development of refractory leach processing technology at its research and development facility in 1988. The R&D staff focused on developing processing methods for low-grade refractory gold resources at Carlin that could not be economically processed by refractory milling methods. The term refractory ore refers to those ores that contain quantities of sulfides and/or organic carbon that result in low recoveries using conventional cyanide leaching. The R&D staff developed two potential processes deemed worthy of further testing: heap biooxidation to liberate gold occluded by sulfides and ammonium thiosulfate leaching for gold recovery from carbonaceous preg-robbing ores. These were piloted in small heaps by the staff of the R&D and Carlin metallurgical labs from 1990 through 1994. By 1994, Newmont's R&D and metallurgical staffs had unlocked the chemistry and kinetics of the two processes, and it was decided that the operations group would be brought in to begin development of a commercial plant. A project manager at Newmont's Denver office was assigned to the project. Scale-up issues such as biooxidation leach pad design; on/off heap heights; handling of various ore types during stacking and reclaiming; operating costs; and environmental, health, and hygiene concerns using a new process chemistry remained unanswered.

Jan 1, 1998

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

Reduce haulage truck accidents resulting from blind spots, with a special emphasis on reducing accidents during backing operations.

Jan 1, 1997

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Forrest T. Moyer

THE injury data and experience in this bulletin are presented in three general sections. The first section contains general and detailed data relating to 1948 injury experience in bituminous-coal and Pennsylvania anthracite mines, separately and combined into totals for all coal mines. The related employment, worktime, production, and productivity data are given in each breakdown of the statistical data. Tables 1 through 22 constitute a subsection and present statistics on number of injuries, frequency and severity rates, average severity, detailed and major causes of injuries, injury records of the coal-producing States, distribution of injuries by part of body, and distribution of injuries by days of disability. Tables 23 through 45, the second subsection, present injury experience in bituminous-coal mines by various selected factors of physical or operating conditions that ma contribute to the occurrence of injuries. The degree of mechanical loading, productivity, size of mine by number of men working and by tonnage mined, thickness of bed, length of shift, number of shifts, type of cap lamps, rating of mine as gassy or nongassy, type of ventilation, and combinations of these factors influencing mine safety are presented in this group of tables. Similar data on Pennsylvania anthracite mines are listed in tables 46 through 63, which comprise the third subsection. The second section of the report contains the generalized annual injury records of bituminous-coal, Pennsylvania anthracite, and all coal mines from the earliest available data through 1948. Tables 64 through 97 list the number of fatal and nonfatal injuries, injury rates, and causes of injuries on an industry basis, the long-term injury records of each coal-producing State, and the related employment, worktime, and production data.

Jan 1, 1952

By Stephen Utter

One function of mining is to supply oil shale of the required grade and characteristics to surface retorts. The mining methods must he safe, efficient, and environmentally acceptable. Although the Bureau of Mines no longer conducts research on methods of mining fossil fuels, including oil shale, its many years of activity in that field resulted in a significant body of findings. This article summarizes some of these findings, with respect to oil shale mining. The large areal extent of Green River formation oil shales and the diversity of geologic, hydrologic, topographic, and other conditions, preclude the use of any one single mining and waste management technique. Instead, in most instances, methods and equipment will be chosen to meet site-specific conditions. Such methods include conventional surface mining (open-pit and strip), underground mining (room-and-pillar, sublevel stoping, caving) and in situ extraction (true in situ from surface drill holes and modified in situ from underground retorts containing rubblized oil shale). Combination or hybrid systems may prove suitable. Both surface and underground backfilling of spent shale waste may be practiced. Tremendous amounts of oil shale must be mined, processed, and the waste shale properly disposed of in order to meet projected industry production goals. For example, about 1.4 tons of oil shale averaging 117 L of shale oil per ton are required to produce one bbl of oil. A plant with a daily production of 8 dam' (50 000 bbl) of oil would thus require some 68 kt of raw shale daily. This is more than the average daily production from any underground mining operation.

Jan 1, 1981

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By H. L. Noblitt, Pauline Moyd, Louis Moyd

The deposit, which forms a ridge -adjacent to the York river, in Mont-eagle township, is held by Monteagle Minerals Limited, of Toronto. The ore is in a Precambrian gneiss which is composed of nepheline, scapolite, andesine and microcline feldspars, muscovite and biotite micas, and -corundum. The major orebody is tabular and is exposed for 1,200 feet along the crest of the ridge. It aver-ages about 90 feet in thickness, dips at about 70°, and was intersected by drilling at a vertical depth of 600 feet. The deposit was prospected for corundum in the early 1900's. Recent exploration was undertaken to deter-mine its potential as a source of high-alumina ceramic material, with by-product corundum and white mica. The program included prospecting, mapping, trenching, diamond drilling, bulk sampling, beneficiation research, a large-scale beneficiation test, product evaluation, market investigations, and plant design. Reserves, to a depth of about 300 feet, are estimated at about 3 million tons.

Jan 1, 1962

By The Staff

"IntroductionThe published information concerning treatment of uranium ores has been very limited as far as Canadian ores are concerned. Such information has dealt mainly with refining processes for concentrates or rich ores, designed to recover radium rather than uranium; these methods could not be economically applied to low-grade ores.The purpose of this paper is to describe treatment possibilities for some of the .ores that have been treated at the Mines Branch, and .to show how the character of these ores influences methods and results.What is a Uranium Ore?Prospecting for uranium has been extremely active during the past two years and a great many occurrences of radioactive minerals have been recorded. Such prospecting has been based to a large extent on the use of the Geiger counter in the fie1d. This equipment is an invaluable aid when the results are properly interpreted.Most definitely, indications of high radioactivity do not always prove the presence of a valuable orebody. First we have to determine:(1) Is the radioactivity due to uranium or to thorium. There is no immediate market for thorium.(2) Can the uranium in the ore be economically recovered.Chemical analysis is the most exact method of determining uranium content, but a fair estimate of the uranium, and also of the thorium, content can be made from the difference in gamma and beta activity. The Mines Branch guards against misinterpretation by determining both beta and gamma activities and, if more than a minor amount of thorium is indicated, then a Chemical analysis is made."

Jan 1, 1950

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011