Search Documents

By E. J. Babcock, W. W. Odell

The Bureau of Mines since its establishment has always taken an active interest in the utilization of lignite and in the development of the lignite dep'osits of the United States. Extensive lignite fields occur in the west central States, notably in North Dakota, Montana, Wyoming, Colorado, and Texas; there are smaller areas in several other States, some of which are widely separated. The total area of the deposits and the total amount of lignite in these several districts are so enormous that the economic value is seldom recognized. To the people of ·the west and west central regions, however, the larger utilization of lignite, in whatever form it may be, is of fundamental importance, and any new methods or uses that promise to open these great lignite fields for more general and more efficient use deserve careful study. Although these lignite deposits underlie areas of thousands of square miles, their development and general utilization has been rather slow. This is no doubt partly because many of the districts are not thickly settled or highly developed in manufacturing industries, but is largely because lignites, from their peculiar physical and chemical characteristics, are low-grade fuels. Most of the lignites in these areas are imperfectly developed coals; many have a more or less woody structure; some belong to the brown-coal type; and others are darker, denser, and more homogeneous, approaching subbituminous coal. The people living in the regions in which these vast deposits occur, especially in the west central part of the United States, are vitally interested in every effort toward bettering lignite as fuel and aiding its wider utilization.

Jan 1, 1923

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

"The theoretical basis of ideal smelting reduction using coal as reductant in a process employing closed loop forced-circulation of hot metal is outlined. In the proposed process, an extensive area of relatively slag-free hot metal is available as a heat sink for absorbing the large amount of heat produced by complete combustion of CO within the furnace. Any slag that is formed within the oxidizing arm of the furnace loop is quickly swept away as a thin floating layer by the bulk movement of hot metal which is induced positively by forced melt circulation and sustained by causing the hot metal and the thin slag layer to overflow into a lower level hearth in which coal is carbonised and dissolved directly into the circulating melt.The proposed process is shown to offer very substantial cost savings over all other direct smelting technology. This is mainly because of its inherently low capital cost and its high energy efficiency. Furthermore, the favourable economics are not reliant on fuel gas credits as all the process gas is combusted within the reactor itself.IntroductionMetallurgical processes in the year 2000 will be compromise solutions to the metallurgical problems that already exist today. It is common knowledge that the mineralogical complexity of certain polymetallic sulphides, for example, precludes high degrees of separation and recovery by conventional mineral beneficiation. steps are therefore being taken towards the development of a truly polymetallic smelting process which will produce simultaneously zinc lead and copper as, metals from complex ores without prior beneficiation(l). In the ferrous extraction industry, the shortcomings of the highly efficient modern blast' furnace are well known and world-wide there is considerable effort being directed towards coal-based ironmaking without the requirement of metallurgical coke as a process intermediate. The current status 0f2Joal-based ironmaking has recently been reviewed by Smith and Corbett. (2)"

Jan 1, 1988

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

The problems associated with achieving adequate accuracy for on-site axial flow fan performance measurements are discussed. The ability to test accurately rests heavily on equipment and installation design detail.Aerodynamic performance trials frequently cannot be carried out due mainly to the poor standard of installation design. In a majority of cases this results in unsteady, non-uniform inlet flow conditions to the fan. Details of installation design features and instrumentation, necessary for successful testing, are given for different types of installations and methods of testing. These cover both conventional practice, and new innovations which can provide solutions to difficult problems. Quantitative aspects of flow measurement are considered for various fan and duct configurations.Although the main emphasis is on large primary mine ventilation units which require on-site testing, the principles outlined have wide application to many other types of fan installation.

Jan 1, 1973

By I. Douni

The aim of this study is to synthesize hydrated compounds of calcium silicate (tobermorite) using as siliceous source perlite milling process wastes, containing more than 70% of SiO2. Calcium silicate hydrates are mainly used for construction of lightweight building materials, plasters, tiles and filters. The effect of temperature, time and particle size of perlite on the quality and composition of the solid product was studied. The solid products were characterized by X-ray Diffractometry, Differential Thermal Analysis and the amount of Acid Insoluble Residue. The synthesis of tobermorite was per-formed by the hydrothermal treatment of perlite waste with a saturated calcium hydroxide solution at a molar ratio CaO/SiO2 of 1, liquid to solid ratio 10 mL/g and 1% w.t. NaOH addition. Three experimental sets were performed. In the first series of experiments the synthesis temperature was kept constant at 205°C while the synthesis time varied from 0.5 h to 24 h. In the second experimental series the synthesis time was kept constant at 2 h while the temperature varied between 150°C and 245°C. In the third experimental set the temperature was 205°C and the reaction time was 2 hours and two perlite waste size fractions were used, a coarse (d50=18 µm) and a fine grained one (d50=8 µm). Reaction products consisted of semicrystalline calcium silicate hydrate (I) and crystalline Al-substituted tobermorite or a mixture of both. An isomorphic Si4+ ions substitution with Al3+ ions in the hydrated calcium silicate lattice was detected by thermal analysis. The experimental results show that good quality crystalline Al-tobermorite can be produced after 6 hours of autoclaving at 205°C or after 2 hours of hydro-thermal treatment at 225°C. Generally, the in-crease of synthesis temperature or time favors the crystallization of calcium silicate phases and enriches them in aluminum. The use of fine grain size perlite is more efficient for the hydrothermal synthesis of calcium silicate hydrates.

Jan 1, 2006

By A. E. Back

A method has been developed in the laboratory for successfully treating titaniferous magnetite ore from the deposit at Iron Mountain, Wyo. The ore is roasted with 15 percent sodium carbonate to convert the vanadium to a water-soluble form and fix the soda for the subsequent electric-smelting step. Approximately 90 percent of the vanadium is recoverable in a product assaying 80 percent V2O5. The leached calcine is briquetted and smelted in a graphite-lined electric-arc furnace. Substantially all of the titanium is recovered in a soda slag, assaying 60 percent TiO2 and 2 percent Fe, which can be upgraded to 75 to 80 percent TiO2 by leaching with dilute sulfuric acid. The upgraded slag could be utilized for the production of titanium dioxide pigments or titanium tetrachloride. About 90 percent of the iron is recovered as pig iron, containing only minor amounts of vanadium, titanium, and sulfur. The high TiO2 slag compares favorably with slag containing about 70 percent TiO2 being produced by the Quebec Iron & Titanium Corp. at Sorel, Quebec. The data obtained from this investigation indicate that a feasible process has been developed for treating Iron Mountain ore, and larger-scale testing is warranted to develop engineering data for the ultimate utilization of this deposit as a source of titanium, iron, and vanadium. There are adequate supplies of basic raw materials, electric power, water, sodium carbonate, coal, and petroleum products within fairly short distances of Cheyenne and Laramie, Wyo., the nearest cities and probable plant- and labor-supply points.

Jan 1, 1952

By Douglas A. Anderson

It is quite common for people exposed to blast vibrations to ask questions such as "How big was that blast on the Richter Scale?" Although it is tempting to dismiss such questions out of hand, for the lay person it is understandable that something which shakes their house should have some sort of measure attached to it. Since a layman doesn't usually know about particle velocity, frequency or the other terms used in describing and regulating blast vibration, the Richter Scale is usually the only measure they can relate to.

Jan 1, 1994

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By L. C. IlsLey, E. J. Gleim

Electrical apparatus because of its flexibility and its adaptability to all classes of service has become essential to the mining industry. Hence the problem of providing electrical equipment that is safe for use in explosive mixtures of methane and air is of prime importance in coal mining. Ilwestigatorsand experiment stations early recognized this fact and much work has been done in the investigation and the development of electrical apparatus for use in atmospheres containing fire damp. The term "fire damp" as applied throughout this bulletin means an explosive mixture of methane and air. Direct-current motors and alternating-current motors of the slipring type when running usually give off electric arcs or flashes that will ignite fire damp. Other 'motors that ha,'e no moving electric contacts may become dangerous through accident, deterioration, or neglect. Auxiliary apparatus such as fuses, switches, rheostats, and controllers may arc, flash, or become heated to snch a degree that fire damp can be ignited. Such equipment is still more dangerous when worn or out of repair. In the United States the development of apparatus for use in gaseous mines has been associated largely with coal-cutting equipment run by electricity. This is undoubtedly due to the use of such equipment at the face of the mine workings, where the chance of igniting fire damp is necessarily greatest. One American manufacturer built a coal-cutting equipment of the totally inclosed type for use in firo damp atmospheres in 1903. Another built similar equipment with special protective devices in 1906, for export. During the years 1910 and 1911, the Bureau of Mines at its Pittsburgh experiment station conducted a preliminary investigation of the safety of such protection as was then in use or under consideration. Five motors were submitted for this investigation, each having somewhat different methods of protection. The results of this investigation were published in Bulletin No. 4G.a

Jan 1, 1920

By S. N. Groudev

Intensive uranium mining activities at the Curilo deposit in Bulgaria has caused widespread contamination over a wide area. A number of receptors including soils and watercourses as well as the ecosystems in the area have been severely affected. Even today, 10 years after the cease of activities, acidic waters generated from the abandoned mining works, the low-grade ore and waste dumps contaminate soil, surface- and groundwater. The present paper describes in general the environmental status of the wider Curilo area and examines the potential of preventive and remedial measures that can be applied in situ to rehabilitate the site and restore the ecosystem. The main rehabilitation technologies examined include modification of the acid generation potential of the pollution sources, treatment of the acidic drainage by means of a natural wetland and in situ bioremediation the of contaminated soils. Finally, a number of efficient indicators are proposed so that the rehabilitation potential at Curilo and similar heavily contaminated sites is assessed.

Jan 1, 2003

By A Markham

Stream diversions are a common feature of mine sites worldwide. From an operational perspective, a fundamental requirement of a stream diversion is that it should convey water flows between two points in a safe, controlled and predictable manner. On the other hand, rivers and waterways are naturally dynamic systems, and many of their natural values are achieved through their ability to alter their forms and processes over time in response to flow events - often in a potentially unsafe, uncontrolled and unpredictable manner. In order to ensure that diverted river reaches achieve the dual objectives of short-term operational stability and longer term physical equilibrium with surrounding landscapes, alteration of form and process must somehow be understood and incorporated into the design process. However, performance targets for waterways are not always easy to define and assessing what is good and bad in such variable systems can be difficult. This paper discusses the role of the stream diversion from the operational, environmental and regulatory/relinquishment perspectives, and how stream diversions must achieve physical stability in the short-term, but dynamic equilibrium in the long-term.CITATION:Markham, A, 2012. Mine site stream diversions - A balance of competing objectives, in Proceedings Life-of-Mine 2012 , pp 215-218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Allen Latham

It started' in 1936 when some Dutch adventurers wanted to scale the highest mountain in the South Pacific. Quite by accident, they discovered the Ertsberg, a contact deposit of magnetite laced with chalcopyrite, in a high mountain valley where it had been gouged at by glaciers and finally left as a solitary pillar for its discovery by a geologist who lent purpose to the expedition, Dr. J.J. Dozy. By the-.time a report was published describing the deposit, war had hit the Netherlands. Perhaps again by accident, the report was uncovered in 1959 by the East Borneo Company. At this point, Freeport entered the scene through its vice president for exploration, Forbes Wilson. During the course of a meeting on laterite prospects, the Ertsberg was introduced and he put the wheels into motion for Freeport to join in its exploration. You might, at this point, ask yourself whether you or your company would have taken on a venture to look at a reportedly large high grade copper outcrop in New Guinea, an unexplored land known best for its inhospitable climate, terrain and head-hunters. I heard the chief executive of one large mining company comment sometime back that neither he nor his company would have gotten involved. I won't attempt to describe the trials of the initial exploration expedition that passed through dense-man grove swamps, tropical jungle and across jagged mountains a distance of some 200 miles to get to the Ertsberg in 1960. It should be chronicled by its participants - Forbes Wilson, Del Flint, and John Bowenkamp. Needless to say, the participants relish the experience but wouldn't be among those volunteering for a return engagement. As a result, the Ertsberg changed from a reported outcrop to a mineral deposit containing an estimated 13 million tons with systematic surface sampling indicating a copper grade of over four percent. Moreover, the deposit extended to an indeterminate depth with the possibility of doubling or tripling. reserves well within reason.

Jan 1, 1971

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

McCulloch, Leon.-Experiments with Sherardizing. Discussed by Fred. L. Wolf, Willis M. Peirce, Jesse L. Jones, O. W. Storey, David R. Kellogg, William H. Finkeldey, L. H. Marshall 2 Bassett, W. H. and Davis, C. H.-Spectrum Analysis in an Industrial Laboratory. Discussed by C. S. Brainin, C. H. Davis, W. H. Bassett, George K. Burgess, George K. Elliott, Leonard Waldo, Keivin Burns 8 Roast, Harold J. and Pascoe, Charles F.-Arsenical Bearing Metals. Discussed by Jesse L. Jones, William A. Cowan,. William K. Frank, William M. Corse, Harold J. Roast 10 Bain, Edgar C.-Crystal Structure of Solid Solutions. Discussed by Ancel St. John, Edgar C. Bain, Paul D. Merica 14 Peirce, Willis M.-Studies on the Constitution of Binary Zinc-base Alloys. Discussed by George K. Burgess, Willis M. Peirce, D. H. Ingall, J. L. Haughton, K. E. Bingham 16 Webster, William R.-Application in Rolling of Effects of Carbon, Phosphorus and Manganese on Mechanical Properties of Steel. Discussed by George B. Waterhouse, J. O. Liebig, Ralph H. Sweetser, H. T. Morris, F. D. Carney, W. P. Barba, John H. Nelson, George K. Burgess 19 Barba, W. P. and Howe, Henry M.-Acid Open-hearth Process for Manufacture of Gun Steels and Fine Steels. Discussed by W. J. Priestley, Haakon Styri, C. T. Patterson, Harry Brearley, W. P. Barba, George F. Comstock, Alexander L. Feild 24 Kellogg, David R.-Electrolytic Deposition of Iron for Building up Worn or Undersized Parts. Discussed by Jesse L. Jones, William Blum, C. R. Hayward, George K. Burgess, C. P. Perin, David R. Kellogg 33 McQuaid, H. W. and Elm, E. W.-Effect of Quality of Steel on Case-carburizing Results. Discussed by H. J. French and L. Jordan, W. J. Priestley, M. H. Schmid, A. E. White, H. J. Stagg and S. C. Spalding, Henry S. Rawdon, J. S. Vanick 35 Phillips, Arthur and Davenport, E. S.-Malleableizing of White Cast Iron. Discussed by Samuel Epstein, H. A. Schwartz, A. E. White, R. S. Archer.... 58 Priestley, William J.-Effect of Sulfur and Oxides in Ordnance Steel. Discussed by Harry T. Morris, William J. Priestley, C. P. Perin, James H. Gray, W. P. Barba, Haakon Styri, Frank D. Carney, W. L. Harbrecht, George F. Comstock, E. J. Janitzky 67

Jan 5, 1922

By G. C. Nowlan, A. Illis, H. J. Koehler

At its iron ore recovery plant at Copper Cliff, INCO produces about 17 million pounds per year of a pure, acid-soluble, dense nickel oxide from nickeliferous pyrrhotite. The process used is also applicable to a broad range of ammoniacal nickel-bearing streams. The product has been widely accepted by the chemical, ceramic and electronic industries.

Jan 1, 1970

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By Richard Guenther

As available space in urban centers becomes more scarce, builders and developers are increasingly turning to vacant, existing structures to meet cities' growing needs. The developers of City Ridge Roadside Development and North America Sekisui House (NASH) - - found a suitable site for their "urban village" at the former Fannie Mae headquarters complex on Wisconsin Ave. NW in Washington, D.C., which had been vacated in early 2018. The urban village will consist of eight new structures centered around the building that currently sits on the site. All told, the project will include 687 residential units, a 150-room hotel, over 150,000 sq ft (13,935 sq m) of retail space, and 62,000 sq ft (5,760 sq m) of office space. A below-grade parking structure will extend across most of the footprint. The Fannie Mae building, which was designed in the Colonial Revival style to mimic the Governor's Palace in Williamsburg, Virginia, was named a historical landmark following a request from the development team. The central portion of its existing masonry structure was built in 1956 on pile caps with small-diameter cast-in-place piles. Two wings, which were added in 1962, were built on belled caissons. There are three levels above grade and one below.

Feb 1, 2022