Search Documents

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

"In order to achieve a high recovery of particles finer than 10µm, three types of dry Tower Mill (VD-1, KD-1, KD-2 and KD-3) have been developed. These mills differ from each other in the size of the comminuting part, the inside diameter and shape of the classifying part and the system involved in the collecting process. The last version (KD-3) of tower mills in which the comminuting and classifying operations has been separated, can produce particles finer than 10µm from a limestone ore sizing from 420 to 3360µm. In this tower mill, products in comminuting section are blown up and transported into the classifying column, made of an inverted cone on top of a cylinder, before they agglomerate and settle down. Fine particles are deported and recovered in a cyclone with a central spiral ribbon.Previous studies on the grinding efficiency of the tower mill KD-3 have shown how the maximum size of collected products increased with the airflow velocity, disturbing in the same way a smooth regulation of the grinding operation with the tower mill KD-3. A complete knowledge of factors that influence the maximum size of collected products is needed, therefore, to increase the efficiency of the grindingclassifying operation and ensure a better control over the collected products. The present study deals with this issue and, assuming that the structure of the classifying column could be one of these factors, its internal structure was modified (insertion of vertical plates, cone or horizontal nets) before carrying out comminution tests that would establish a relationship between the inward shape of the column and the maximum size of collected products. It was found that the weight of products collected in the cyclone decreases when a cone or some horizontal nets are inserted inside the column. At the same time, the weight of products collected in the column increases. This is due to the fact that coarse particles blown up from the comminution section collide with the base of the cone or the nets and settle down the bottom of the classifying column. Therefore, the cone and some horizontal nets inserted inside a classifying column, have the particularity to stabilize the maximum size of particles (15.1-17.5µm and 8.4-11.3µm) in the cyclone even when the airflow velocity in duct increased. These tools could of great help in the production of particles of definite size to fit for instance the paper industries requirements (production of limestone material sizing - 10µm as paper filler)."

Jan 1, 2003

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95.9.5.5 mt (105.770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/ml (0.36 oz/st) silver with 0.94 % copper. 1.10 a lead and 11.06% zinc. Ore reserves at El Roble are estimated as 1.1% Mmt (1.21 million st) grading 4.89% copper and 3.39 g/mt (0.099 oz/st) ,old. Geologically possible reserves at Equis may total 1.6.Mmt (1.76 million it). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1984

By Eugene O. Binyon

"Belt and shaker conveyors, used singly or as combined units, have for many years been an integral part of many coal-mine haulage systems. The belt conveyor has also been used extensively as a main haulage unit in open-pit iron-ore mines of the Lake Superior district, particularly on the Mesabi Range. Few underground metal mines, however, either in the ferrous or non-ferrous branches of the mining industry, use the conveyors exclusively or even extensively for underground haulage. At present, only five iron-ore mines in the entire Lake Superior district have belt- or shaker-conveyor installations of any significant size. Of these mines, three are in the Crystal Falls-Iron River district of Michigan on the Menominee Range, one is on the Marquette Range near Ishpeming, Mich., and one is on the Mesabi Range near Keewatin, Minn.Results of the studies of tackless haulage in the Lake Superior district will not permit the establishment of any formula to prove or disprove the advantages of belt or shaker systems at all underground mines. The studies do show that trackless haulage can be used to advantage where the proper conditions exist. Advantages are particularly apparent when development can be planned sufficiently in advance of exploitation to permit installation of belts or shakers as part of the development program and where the systems are extended to include haulage in stopes as well as main entries.During the winter of 1947-48, the Bureau undertook a study of all of the underground ore conveying systems known to be in operation in the Lake Superior district for the purpose of making available to the entire mining industry the technologic data developed in the area. Because conditions that led to the installation of the belt and shaker conveying systems were often a function of the character of the deposit or the method of mining, a brief description of those conditions is included in this report.After a preliminary investigation into the extent to which trackless conveyors were employed in the district, it was found that a detailed study at five bites would result in fair appraisal of that method of haulage in the underground iron-ore mines.Each of the five significant installations is described separately in this report. In one instance, however, company policy does not permit identification of the mine wherein the conveying is done. In that instance the operation is designated as mine ""A"".Unless otherwise specified, all tonnage figures quoted herein are gross.The cooperation of officials of all of the companies operating underground mines in the Lake Superior district permitted successful completion of preliminary studies of mining practices and conveying systems.Special acknowledgment is made to R. D. Satterley, general superintendent, and to operating staffs of the Sherwood and Morris mines of the Inland Steel Co. The assistance given by W. D. Whitman, assistant superintendent, and Douglas Tippett, mine captain at the Morris mine, and P. D. Pearson, superintendent, R. O. Marsten, engineer, and W. Johnson, mine captain, at the Sherwood mine, is acknowledged."

Oct 1, 1949

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By Mats Keisu, Bengt Niklasson

The Sofia project has increased the level of knowledge and technique within tunnelling, drifting and contour blasting.

Jan 1, 1992

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By J. F. Lupo

There are numerous mines throughout the world that have open pit highwalls developed partially or wholly in soil or soil-like materials. Soil-like materials are considered to include soils (either transported or residual) and highly weathered rock, which may have soil-like behavior. These materials generally have characteristics or material properties that vary considerably from those of moderately weathered or fresh rock. Given these differences, it is important to consider the characteristics of soil-like materials to design safe open pit slopes. In the design of open pit slopes in soil-like materials, it is important to recognize the behavior of these materials is strongly dependent upon their mineralogy, degree of weathering, cementation, stress history, depositional history, and presence of water. As a result, soil-like materials may contain one or more of the following characteristics that can have a significant effect slope stability and design: - Relict structural features (joints, faults, etc), - Sensitivity to moisture (both wetting and drying), - Zones of alteration with variable strength and drainage characteristics, - Zones of low permeability creating perched ground water conditions, and - Undrained and drained strain softening or strain hardening behavior.

Jan 1, 2011

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By B. M. Hamilton

"IntroductionTHE PROCEDURE and technique for drilling holes has probably undergone as great a change during the past ten years as any one of the other operations conducted in hard-rock mining. During this period, we have seen a change from the heavy leyners and drifters to the light jackleg type of drill machine; from steels that were forged and hardened on the bit end to the inserted •carbide-tipped rod, from the necessity of providing special bit-end fabrication and beat treatment of shank steels to the simple grinding or turning of a plain section on a shank with no heat treatment required for bit attachment.When the steel maker was first called upon to manufacture a hollow drill rod, it was required that the steel must not only have sufficient strength and fatigue resistance to cope with the stresses of service, but also must be capable of being heat treated on the bit end to a high hardness for resistance to wear and abrasion . Little was known at that time about alloy steels and the beneficial effects to be gained from additions of chromium, nickel , and molybdenum. So it was that the plain 0.80 per cent carbon analysis was selected, since it had already proven to be a suitable grade for chisels, hammers, and other such shock tools. This grade has long endured the test of time and is still used in considerable tonnage today, particularly by the construction industry.As the metallurgist learned more about the influence of alloying elements, a new hollow drill analysis was placed on the market in the early 'thirties'."

Jan 1, 1954

By R Garzon

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analystsÆ inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted æfloorÆ value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By Ronald P. Hollenbeck

This study reviews and discusses the fluorspar industry in the Eastern United States, with emphasis on factors controlling the industry such as production, consumption, uses, and transportation. The greatest potential for increased consumption of fluorspar in the immediate future was found to be in the manufacture of fluorine chemicals and steel. Important factors affecting the future domestic industry include imports and the maintenance of adequate domestic fluorspar reserves. Exploration, commercial deposits, mining and milling, reserves, and new developments in the industry are covered.

Jan 1, 1967

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.' From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St.-Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By R. C. Adams

This report describes the feasibility of mining the oil-shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt, at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976