Search Documents

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Frederick A. Mumpton

Recent findings by medical workers on the association of certain zeolite minerals with the high incidence of pleural mesothelioma in two small Turkish villages have caused considerable excitement both in medical circles and in the synthetic and natural zeolite businesses. The 42 cases diagnosed between 1970 and 1977 in one community of 600 population in a region of altered volcanic tuff represent a virtual epidemic of this rare malignancy which normally strikes only about one person in a million. Cancer workers around the world expect that detailed environmental and epidemiological studies of the disease in these areas will shed considerable light on the cause of this particularly lethal form of lung cancer. Scientists and engineers developing uses for zeolite materials in industry and agriculture, however, are justly concerned that the preliminary results available on this situation will be used by environmental and regulatory organizations to label an entire group of miner- als as carcinogens on the basis of what is little more than circumstantial evidence. Although there is no question as to the large number of cases of mesothelioma in these areas of central Anatolia, the work to date has suffered from a lack of sound geological and mineralogical input. Ataman (1) stated that a "correlation" exists between mesothelioma and zeolites in this region; however, the geological data needed to document a direct relationship between the presence of zeolites in the volcanic tuffs surrounding the villages in question and the rate of malignant lung disease in the inhabitants have g been obtained, nor has evidence that suggests a cause-effect relationship between zeolites and cancer been reported. To provide fundamental information on the distribution of zeolite minerals in areas of central Turkey where high incidences of pleural mesothelioma have been reported and to evaluate from first-hand knowledge the published reports and news releases of medical workers engaged in assessing the problem, the following investigation was made.

Jan 1, 1979

By Circadian Technologies

Alertness levels naturally fluctuate during the day and night Basic functions ??digestion, body temperature ? follow predictable 24-hour patterns Adjustment to night work creates health challenges for shiftworkers Performance decreases during overnight and post-lunch dip hours Fatigue supercedes training & experience Fatigue is a major cause of human error

Jan 1, 2010

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

By Dan Preston, Shane Yanagisawa, Robert Marshall, Don Deere

Geotechnical Baseline Reports often estimate the number of cobbles that will be encountered in terms of volume or weight. These estimates are practically impossible to verify in the field. ClaroVia Holdings in conjunction with Frontier Kemper Constructors Inc. developed Digital Geologist 2.0 to classify and count cobbles discharged from an EPB TBM at the RSC7 project in Burbank, CA. The system worked by using two stereoscopic laser sensors with a global shutter to scan and count cobbles at 12 frames per second. Results of the effort are revealed along with lessons learned and paths for improvement.

Jun 13, 2023

Geophysical Abstracts 1 - 83 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey. Abstracts 112 and 113 were issued in mimeographed form by tine Bureau of Mines as Information Circulars 7256 and 7257. 1. GRAVITATIONAL METHODS 7004. Campbell, R. B. Florida's Geological Structure and Gravity. Proc. Florida Acad. Sciences for 1540, Gainesville, Fla., vol. 5, 1541, pp. 73-84.

Jan 1, 1943

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By R. Simard

"Conventional exploration strategies identify many mineral deposits as potentially interesting, although only a few of them turn out to be of economic importance. In the context of exploration for sulphide nickel deposits in the Canadian Shield, a decisional model, based on a statistical study of parameters relative to nickel deposits as well as to barren sulphide occurences, has been developed.Because such geophysical variables as gravimetry, aeromagnetism and topography could be related to the relative importance of nickel-bearing deposits, a statistical analysis of 13 such variables was carried out for 98 targets which were considered promising after conventional exploration. Among these 98 targets are36 sulphide nickel deposits in the Canadian Shield and 62 drill-tested non-economic occurrences. The results of this study led to the development of a linear logistic model that permits evaluation, for each of the targets, of the probability of finding a nickel deposit of potential commercial interest. This decisional model can thus complement conventional exploration strategies.RésuméLes stratégies conventionnelles d'exploration définissent un très grand nombre de cibles comportant un inténet minier potentiel dont seules quelques-unes correspondent à des gisements économiquement importants. Dans Ie cadre de l'exploration des dépôts nickélifères du Bouclier Canadien, nous avons défini un modelé de décision fonde sur l'étude statistique de divers paramètres relatifs tant aux gisements d'importance qu'aux cibles dites stériles.Ayant fait l'hypothèse que certaines variables géophysiques (gravimétrie, aéromagnétisme et topographie) peuvent suffire à fournir des indications sur l'importance relative d'un gisement nickélifère, nous avons entrepris l'analyse statistique de 13 variables évaluées sur un échantillon de 98 cibles considérées comme potentiellement intéressantes par les stratégies conventionnelles d'exploration. Ces 98 cibles se composent de 36 dépôt nickélifères d ‘importance recontrés sur tout Ie Bouclier Canadien et de 62 cibles stériles reconnues par forage. Nous avons défini à l'aide de ces données un modèle logistique linéaire. Ce dernier nous permet d'évaluer pour chacune des cibles les chances de trouver un gisement. Ce modèle de décision peut done s'inscrire comme outil complémentaire aux stratégies conventionnelles d ‘exploration."

Jan 1, 1980

The first metal-mine accident-prevention course was prepared and published 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars on accident prevention at metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By Julius G. Chang

Against the receding background of the October stock market crash and the December overhang of inventories, the economy began with a shaky start in 1988. As 1988 began, the Administration's estimate of real growth for 1988 had just been reduced from 3.5% to 2.4% and economists and other ob-servers were concerned that the expansion that was 5 years old might be near the end and that a recession might be around the corner. The ensuing moderately strong economic activity, however, belied all the negative signals that were evident earlier, and the real GNP continued to grow at an estimated 2.3% annual rate during the first quarter of 1988, extending the ongoing recovery into the sixth year (table 1.). The relatively accommodative policy of the Federal Reserve Board (the discount rate was cut by 0.25% in January), a strong performance by the export sector, and the revival of consumer spending were major forces underlying the economic strength. But as the quarter drew to a close, signs of tight capacity utilizations were apparent in many of the export and capital goods sectors, including textile, chemical, plastic, metal, and machinery. Employment was at a record high level while the unemployment rate was close to a historical low. Prices were rising at a faster pace than those of 1987, and the dollar resumed its slide after a brief recovery in January and February. These factors gave rise to the fears of higher inflation. Long-term interest rates increased, casting a pall over the prospect of a robust growth for the rest of the year.

Jan 1, 1988

By P. N. Erasmus, M. Heyns, M. J. Pretorius

The characteristic of stope supports plays a vital role in the design of the supports. This paper deals with the characterisation of both cellular lightweight concrete and timber supports since both supports absorb and dissipate the energy in different ways. The behaviour of the support and hence its performance is simulated for different loading conditions by constructing a model consisting of various mechanical components like springs, dampers and blow-off valves. When the force exerted by the stope support increases significantly during deformation of the support, the stresses in the hangingwall could exceed values where failure of the hangingwall may occur. There is a need to understand this phenomena and the work presented in this paper is a first attempt to start with the characterisation of the stope support. Les caractéristiques des supports de taille jouent un rôle vital dans la conception des supports. L’étude présente traite de la caractérisation des supports cellulaires en béton léger et en bois, puisque ces deux types absorbent et dissipent l’énergie de façons différentes. Le comportement du support et par conséquent sa performance est simulée pour des conditions différentes de chargement en construisant un modèle qui consiste en des organes mécaniques variés tels que ressorts, registres et valves d’échappement. Quand la force exercée par le support de taille augmente considérablement pendant la déformation du support, les contraintes dans le toit peuvent dépasser des valeurs qui pourraient entraîner la défaillance du toit. Il est nécessaire de comprendre ce phénomène et l’étude ici présentée constitue un premier essai dans la caractérisation du support de taille. Die Charakteristika der Strossenunterstützung spielt im Design von Unterstützungen eine vitale Rolle. Diese Arbeit befaßt sich mit der Charaketerisierung sowohl der porösen Leichtgewichtbeton- als auch mit der Holzunterstützung, da beide Unterstützungen Energien auf verschiedene Art und Weise absorbieren und auflösen. Das Verhalten der Unterstützung und folglich seine Leistung wird für unterschiedliche Ladezustände simuliert, indem ein Model konstruiert wird, welches verschiedene mechanische Komponenten wie Federn, Dämpfer und Ausblaseventile enthält. Wenn die von Strossenunterstützung während einer Unterstützungsdeformation aufgebotene Kraft signifikant ansteigt, könnten die Spannungen im Bereiche des Stollenfirstes Werte überschreiten wo ein Versagen des Stollenfirstes eintreten kann. Es besteht die Notwendigkeit dieses Phänomen zu verstehen, und die Arbeit, die in diesem Elaborat dargestellt wird, ist ein erster Versuch, mit der Charaketerisierung der Strossenunterstützung zu beginnen.

Jan 1, 2003

By Denis Bois

La Bolivie est un pays en développement qui compte une tradition minière qui précède même l?établissement espagnol en Amérique. Pendant toutes ces années, l?exploitation minière s?est faite sans grands égards pour l?environnement. Au cours des dernières années cependant, le gouvernement bolivien a modifié ses lois afin de rendre nécessaire la prise en compte de l?environnement dans le processus d?exploitation d?une mine. Dans le cadre d?un projet MRN-ACDI1 visant à renforcer le secteur minier en Bolivie et ses retombées pour la population, l?URSTM2 a été mandaté pour développer et mettre en place un programme académique de gestion environnementale minière, basée sur l?expertise canadienne. Ce programme vise à renforcer les institutions académiques boliviennes responsables de la formation en environnement minier en Bolivie ainsi que les ministères et agences gouvernementales concernées.

May 1, 2001

By J. G. Eacott

This paper reviews the role of oxygen potential and the advances that have been made in the application of tonnage oxygen in copper smelting. Brief reference is made to reaction kinetics before attention is turned to the thermodynamic considerations in copper melting to illustrate the importance of oxygen and. oxygen potential in the component parts of the overall smelting process. The chemical potential diagram for the Cu-Fe-S-O-Si02 system is used to elucidate the difference b etween the conventional matte smelting process and the modern continuous processes. A progressive oxidation scale' is constructed to show the common elements which exist, and the matte grades produced, during the smelting of concentrates to blister copper in commercially available copper smelting processes and those under development. The common route in producing blister copper from molten mattes, regardless of process, is illustrated on the Cu-Fe-S equilibrium phase diagram. The essential features of oxygen enrichment, in terms of its effect on combustion conditions (i.e. oxidation of fuel and sulphide minerals) and the heat balance are outlined. The benefits of oxygen enrichment are listed. The influence of tonnage oxygen and its effect on productivity, fuel savings, gas volume and strength in various copper melting processes are examined as a state-of-the-art review. Reference is made to the economics of tonnage oxygen utilization.

Jan 1, 1983