Search Documents

By S Norman

The Water Delivery Alliance (WDA) was established to design, construct and commission the pump station and desalinated water delivery pipeline to link the desalination plant on the Kurnell Peninsula (constructed by others) with the existing distribution network at Erskineville, Sydney, Australia. The WDA consisted of McConnell Dowell Corporation Ltd (Macdow), Bovis Lend Lease Pty Ltd (BLL), Kellogg Brown and Root Pty Ltd (KBR), Worleyparsons Ltd (WOR), Environmental Resources Management Group Inc (ERM) and Sydney Water Corporation (SWC).Sydney’s Desalination Project is one of the initiatives to secure Sydney’s water supply against the effects of climate change, population growth and drought. The desalination plant, 100 per cent powered by renewable energy, can supply up to 250 million litres of water per day (mld), which is up to 15 per cent of Sydney’s water needs. The project involved the construction of an 18 km pipeline with an ultimate capacity of 500 mld to accommodate any future increase in the output of the desalination plant.The Alliance procured three full-face tunnel boring machines (TBM) from Herrenknecht AG to construct the 6.5 km of tunnel that would provide a conduit for the DN1800 welded mild steel cement mortar lined (MSCL) pipeline at a number of locations along the route. Nineteen shafts and 16 tunnels were required to complete this work.Crucially one of the TBM drives involved construction of a tunnel into Botany Bay under protected marine life habitats; enabling the connection of the MSCL water carrier pipeline into the dredged section of pipeline underwater, approximately 800 m off-shore in Botany Bay.This paper details the retrieval of the 17.4 m long TBM from the ocean floor upon completion of the Botany Bay tunnel allowing for subsequent use on the Project. Elements covered in the paper include the 835 m tunnel, design and construction techniques for the tunnel and recovery, and details of the methods used to install the DN1800 water carrier pipeline.

Mar 8, 2011

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By C Skublak

The Government of Canada recently passed a new regulation to control the liquid discharges from metal mines in Canada. The Metal Mining Effluent Regulation of the Federal Fisheries Act will come into force within the next six months. As a result the Ontario Regional Office of Environment Canada has developed a compliance promotion program to accompany the new regulation. How the mines implement the regulation will be key to its success. This paper will briefly outline the components of this regulation, including the reporting structure, the discharge parameters and limits, as well as the requirement for the mines to conduct long-term environmental effects monitoring on their effluent discharge. The presentation will give a brief account of the compliance promotion program, and then focus on the spill trends from Ontario mining operations. The province of Ontario has the largest concentration of metal mining operations in the country with approximately 40 active mines.

Jan 1, 2002

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By S Jahanshahi, D R. Swinbourne

The classical metal-slag-gas equilibrium technique was used to study the thermodynamic activity of cobalt, iron and their oxides in iron silicate based slags containing under controlled oxygen potential (3.70 x 10-8 to 2.95 x 10-7 atm) at 1573 K. The measured activity of cobalt oxide in FeOx-25 wt per cent SiO2 slags showed positive deviation from ideal behaviour for melts with up to ten wt per cent CoO. At higher silica contents, the behaviour became closer to ideal and in accord with previous studies on silica saturated slags. The activity coefficient of FeO in these slags had virtually no dependence on the CoO content. Partial substitution of silica by lime resulted in an increase of the activities and activity coefficients of CoO, FeO, Fe2O3 and Fe3O4. The results indicate that saturation of the slag with a magnetite phase occurs at CaO contents of five wt per cent and higher. Phase equilibria studies SiO2-FeO-Fe2O3-CaO slags containing cobalt were also carried out using the drop-quench technique. Results from these experiments confirmed the formation of a magnetite solid solution containing about three wt per cent CoO at lime contents of five wt per cent and higher at 1573 K and 2.9 x 10-7 atm of oxygen.

Jan 1, 2000

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By M Olsen, L van den Berg

Bowen Basin coalmines suffer from hot and humid ambient conditions during the summer period. The ambient conditions combined with high VRTs, increasing depth of working and significant equipment heat loads results in heat issues underground. Coalmines operate under heat stress management plans as required by legislation with associated trigger action response plans (TARPs). Some mines also employ refrigeration as part of their heat management strategy.A recent case study was conducted on a mine producing about 4.5 Mt/a from their longwall and experiences summer surface ambient temperatures of about 23.5&#186;Cwb. The expected virgin rock temperature is 46&#186;C at 300 m depth. The mine currently introduces a modest amount of surface cooling at the portal using ‘off-the-shelf’ air conditioning units. This system does not effectively manage face temperature primarily due to positional inefficiency.Underground conditions remain hot in summer and work is typically undertaken in accordance with the Heat TARP. This has a direct impact on the productivity of crews, worker comfort and also negatively impacts the workforce morale. The mine commissioned a study to determine a refrigeration strategy aimed at maintaining underground conditions below TARP levels 90&#160;per&#160;cent of the time.The ventilation network model was calibrated against actual temperature data to simulate the heat loads including longwall, conveyor system, strata and auxiliary diesel fleet. This model was then used to determine the cooling requirements for bulk surface cooling, bulk underground cooling, surface district cooling and underground district cooling strategies.These estimates were used to undertake a total owning cost trade-off for the different strategies. The study concluded that a chilled air shaft has the lowest technical risk but the highest total owning cost due to shaft development needs. Introducing chilled water to an underground cooler via boreholes offered the lowest total owning cost and was therefore recommended.CITATION:van den Berg, L and Olsen, M, 2017. Heat load assessment and mine cooling strategies for a longwall coalmine, in Proceedings Australian Mine Vent Conference 2017, pp 231–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

Grinding and Beneficiation Characteristics of a Low-Grade Haematite Ore

Sep 13, 2010

Advances in technology have led to larger and deeper open pit mines and, consequently, also increased the potential economic impact associated with slope failures. If the ultimate aim of mining operations is to maximise project profit, it is surprising to see related research activities have mostly been focusing on technical areas such as slope stability modelling, but with limited studies conducted to date to assess the relationship between geotechnical uncertainties and economic risk. Given most major decisions in the mining industry nowadays are made by management staff with financial background, any design approach that would help to link slope stability analysis results with monetary values would no doubt enhance communication between geotechnical practitioners and decision makers. This paper presents a study which assesses economic impact of slope failures to assist in mine planning. The study also estimates the impact of slope failures on project value, which would enable economic risks associated with pit slope designs to be closely examined. The proposed risk assessment techniques, used by financial institutions for many years to assess portfolio risks, can assist geotechnical practitioners in quantifying risks of slope failures. Risk-adjusted concepts are also suggested to assist management in selecting a slope design with optimal risk and return ratio.

May 1, 2010

By Walter L. Finlay

The Bureau of Mines has developed prototype instruments promising to improve the ability to warn of imminent roof falls. An unusually good opportunity to test these comparatively under natural caving conditions was afforded by the forecasted caving in August 1977 of a mined-out region of the White Pine Mine. The latter&apos;s rock strata closely resemble those in many coal mines. The anticipated cave was of the competent-roof/weak-pillar type. It occurred as, and when, predicted. Automated convergence and bed separation gages agreed well with the standard manual convergence gage measurements. A micro seismic gage was found to be insensitive to the fall and may require different test conditions for effectiveness. A roof resistivity unit was tested under a separate Bureau of Mines contract. (No. H02720J7). An unplanned addition showed interesting potential.

Jan 1, 1978

By Dorothy M. Richardson

The Bureau of Mines has participated in the American Petroleum Institute Research Project 48A (API-RP48A) program on the Separation and Identification of Sulfur Compounds in Crude Petroleum. The lack of reference compounds or infrared spectral data has made difficult the identification of individual sulfur compounds boiling above 140° C. The recent acquisition of 24 alkylthiophnnes has made possible a limited study of this important class of sulfur compounds. The infrared spectra of 2-monoalkylthiophenes and 2,5-dialkylthiophenes for the 2 to 15p range are reported. Correlations for determining the 2-alkyl and 2,5-dialkyl substituted thiophenes are derived from this information. The 2-alkylthiophenes show a unique pattern in the 5.50 to 6.54 region, while the 2,5-dialkylthiophenes show a distinctive pattern in the 5.6µ to 6.7µ region. A skeletal vibration occurs in the 9.5 to 10.0µ region for all of the thiophenes investigated. These data will aid the infrared spectroscopist in the identification of compounds of the type reported.

Jan 1, 1961

By Jr. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen con-tent of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

Jan 1, 1967

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By S. Setayeshgar

The identification of potential accidents on construction sites has been a major concern in the construction industry and it needs a proactive safety plan to reduce the risk of accidents. There are no efficient methods for checking if safety measures are taken properly on construction sites. Consequently, workers on site are not given enough awareness about dangerous areas. In addition, construction sites are dynamic and on-site situations are changing in terms of permanent and temporary structures and facilities. This information can be represented using Building Information Modeling (BIM). This paper proposes the integration of BIM and safety risk analysis by considering the risk levels associated with the work spaces of different construction tasks. Work spaces are generated in a BIM model according to the Work Breakdown Structure (WBS) of the project, reference objects in the BIM, and the schedule and resources of the task. Each work space is assigned to one or more tasks or functions, e.g., work spaces for specific tasks, shared spaces (paths), storage spaces, or spaces prohibited to workers. The assignment of work spaces is based on the workers, equipment and materials involved in the task. All the work spaces are associated with a specific duration according to the schedule of the project. Then risk evaluation of the construction site is applied in order to evaluate safety risks based on their severity and the degree of exposure of workers. For example, work spaces for storing hazard materials and for heavy construction equipment have higher risks than other work spaces. The results of the risk evaluation can be visualized in a 4D BIM model.

Aug 1, 2013

By Richard C. Banting

Excessive vibration is known to have an adverse affect on soft body tissue and operators of heavy mining equipment can be exposed to vibration that exceeds levels recommended in international guidelines (ISO 2631-1, for example). Research has found that many of the seat and suspension systems currently used in mine haul trucks and load haul dump vehicles are actually amplifying the vibration. This overview presentation will outline the current research being conducted at Laurentian University and the University of Western Ontario, and the roles of partners in rating the ability of a number of commonly used mine vehicle seats to isolate harmful vibration.

Oct 1, 2010