Search Documents

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961

By P. J. Bhonde, R. D. Angal

Conventionally low carbon ferromanganese is manufactured globally by refining high carbon ferromanganese in liquid state. This process is an expensive and lengthy technique. Hence, the present work was undertaken with the objective of understanding the feasibility and kinetics of the solid state refining of ferromanganese. The process involved transformation of carbon rich carbides viz. Mn3C2, Mn7C3 into metal rich carbide i.e. Mn15C4, Mn23C6 by subjecting the alloy powder to a flowing stream of carbon dioxide. Effect of the process governing parameters such as time, temperature, particle size, pressure on the extent of decarburization was studied. Without any loss of manganese in the form of fumes or slag, it was observed that, there was substantial reduction, viz. 65 per cent in the total carbon content, by this technique. Subsequently, the process was investigated to find out the mechanism of carbon removal. Depending upon the temperature and the particle size, it was found that the rate controlling mechanism changes from chemical reaction control to product layer (ash) diffusion control. The activation energy for each of the aforesaid mechanism was computed. The values thus obtained substantiated the aforesaid mechanisms.

Jan 1, 2004

By V. Grujic, M. Grujic, D. Salatic

"Two areas are involved in the research work of the comminution process (crushing and grinding). The first one involves the changes of the size class distribution values that are definded by the differential equations in the function of the ore property and working conditions. The second area involves the comminution of the different levels in order to optimize the working parameters and to decrease the operational costs in the grinding process.We have studied, in detail, the possibility of functioning the crusher at the maximal loading, over 4500 kN, ball mills with diameters larger than 5.0 m and semiautogenous mills with diameters larger than 10.0 m.Using the computers, we have achieved the maximal loading range of the crusher, over Fc ? 4500 kN in the crushing process. In the grinding process, using the adequate differential equations in the automation process, we have established the correlation between the pulp mass capacity in the mill, pulp dencity, ore fineness in the pulp and recirculating ore charge.With the appopriate text, equations and graphs, this paper shows the results of our several years research work in the laboratory and in the ore comminution plant of Majdanpek Copper Mine."

Jan 1, 2003

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermo-physical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at the University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous case is modeled with walls, each having a different set of thermo-physical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By A. L. Edwards

A two-year study focused on current noise exposure levels in the South African mining industry, aimed at helping the Mine Health and Safety Council of South Africa meet its milestones for eliminating noise-induced hearing loss (NIHL). Methods A multi-task methodology was adapted from international baseline studies to determine the exposure to noise in both large-scale and small- to medium-scale mines. Results On average, 66.7 per cent of the employees sampled in year 1 and 78.4 per cent in year 2 were exposed to noise levels of above the 85 dB A legislated occupational exposure level. Conclusions Information obtained through the study could be developed into a national personal noise exposure database, including audiometric results, equipment noise emission levels and initiatives for noise engineering control by mines and equipment manufacturers to facilitate targets of eliminating NIHL. Keywords Noise exposure levels, mining industry, noise-induced hearing loss

Jan 1, 2011

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By M. Alley, P. Schroeder, L. Zelazny, S. Nagle

The Old Hickory mineral sands ore body in Virginia (>2000 ha) currently supports a productive rowcrop agriculture. Reclamation experiments were implemented on pilot-scale mining pits from 1995 to 1998. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes treated with 112 Mg/ha yardwaste compost. Post-mining productivity was estimated to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/ cotton) in sequence when compared to undisturbed soils. Variability in surface texture and compaction limit restoration of soil productivity.

Jan 1, 2002

concentrations) and physical nature of receiving streams, which in turn affects the stream ecosystem. Benthic macroinvertebrates are used to illustrate these impacts, and to investigate natural recovery in affected streams. In Charming Creek, a severely impacted stream in the Buller District, the macroinvertebrate community recovers diversity and the proportion of sensitive species (EPT) in the community is more significant with increasing downstream distance from the source of AMD. This is most likely due to dilution of AMD contaminated water by tributaries to the Charming Creek mainstream. Other impacted systems with less dilution from tributaries did not display similar levels of recovery. The effectiveness of remediation products BauxsolÖ and Zeolite was investigated using laboratory trials. Both products mitigated the toxicity of AMD and enhanced the survival of mayflies exposed to AMD contaminated water. Such products may be of use in the New Zealand environment but are likely to be most effective in conjunction with other systems (eg wetlands). Mitigating the impacts of AMD on stream ecosystems needs to include systems to directly address water chemistry issues (low pH, high metal concentrations) as a component of a holistic approach to restoring environmental conditions.

Jan 1, 2003

By R C. A Minnitt

The Witwatersrand Supergroup is host to the world’s largest gold deposits. The location, quantity, grade, continuity and other geological characteristics of a Mineral Resource are either known, estimated from specific geological evidence and knowledge, or interpreted from a well constrained and portrayed geological model. Establishing such a model is an integral part of the evaluation process in the Anglogold Ashanti (AGA) group, and is referred to as a Geoscience Business Model for the mining operations. The geological model established over the years has relied on detailed descriptions of the mineralisation, and understanding of the regional and local geology of the Witwatersrand sediments, in the West Wits and Free State goldfields. The processes of data collection in regard to underground stope and developing mapping, structural and sedimentological mapping, and the geological inputs to mine planning systems are described, together with aspects of drilling, sampling, grade control, and data management. Anglogold Ashanti’s Geoscience Department employs a complex and unique process to generate the Mineral Resource, including a 3D geological structure model of the orebodies which are usually highly faulted, and a robust mineralisation/facies model on which the decisions about domain boundaries are established. A Mineral Resource Inventory System (MRIS) has a dynamic graphic interface to the resource database that is used for compiling the resource statement. It is also used to determine the gold-called-for, as well as short and long-term planning. A unique estimation process using the extensive closely spaced stope face sampling database and the more widely spaced surface drilling information is used in combination in the Macro Co-Kriging estimation. The use of different support sizes in the C0-Kriging process is preceded by the equally unique ‘clusterisation’ and ‘acceptorisation’ procedures by which the data are quality controlled and assured prior to their use in the kriging process. The Mineral Resource and Ore Reserve estimates are classified according to the SAMREC code through a method that ensures that they are compliant, auditable, transparent and reconcilable with previous Mineral Resource and Ore Reserve statements.

Aug 22, 2011

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By M. Kerr, Petra Lampinen, Jinming Zhang, Petra Brodin, C. Hull, Nils-Johan Bolin, R. Asmatulu

"According to Darcy’s equation, the rate of dewatering varies as inverse square of the surface area of the particles to be dewatered and is proportional to the pressure drop across a filter cake. Thus, the difficulty in dewatering fine mineral concentrates can be overcome by using high-pressure filters. When treating ultrafine particles, however, it is often necessary to further dewater the filter cake using a thermal dryer. In the present work, novel dewatering aids that can reduce the pressure requirement have been developed. The reagents are designed to reduce surface tension, increase particle hydrophobicity and increase capillary radius, all at the same time. They were tested for dewatering mineral and coal concentrates in both laboratory and pilot-scale tests. The results show that the use of the novel dewatering aids can substantially reduce cake moistures and, at the same time, increase throughput. In this communication, the case history of using the reagents commercially at the Garpenberg concentrator is given. The use of the novel dewatering aids allowed the operators to use a vacuum filter to obtain desired cake moistures and obviate the need to use a thermal dryer.INTRODUCTIONDewatering is an integral part of mineral and coal processing operations, as it is necessary to remove water from concentrates (or clean coal) to minimize shipping costs, meet contract specifications, and recycle the process water. In general, the cost of dewatering increases with decreasing particle size, which can be attributed to the difficulty in removing the water trapped in the pores (or capillaries) formed between the particles constituting a filter cake.The various parameters affecting the process of dewatering, including the effect of particle size, can be understood in view of Darcy’s equation (Darcy, 1856):"

Jan 1, 2005

By D. W. Hendriks, C. Daoust, K. V. Konigsmann

"The concentrator of Mattagami Lake Mines Limited commenced operation in 1963. It had been designed with instrumentation proven at that time. New control techniques were added in subsequent years.An on-stream X-ray analyser was installed in 1968. It provided circuit analyses for six years without the aid of a computer. In late 1974, control of the flotation circuit by computer was incorporated into the system. Flotation efficiency improved considerably, zinc"" recovery increased by one percentage point and concentrate grade by four-tenths of a percentage point. Reagent costs decreased modestly through reduction of copper sulphate consumption."

Jan 1, 1976

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By O E. Jr Crenwelge

Frequency domain, single-charge vibration signatures are used to interpret the characteristics of explosive impulse excitation and ground vibration transmission. The effects of charge height, charge splitting, and different blasting agents are first discussed. Then the effects of rate of change with distance of overburden material properties and layer or surface geometries are illustrated.

Jan 1, 1988

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007