Search Documents

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No.1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No.2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No.2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

May 11, 2007

In the context of sustainable development, the Minerals Council of Australia (2010) states that 'investments in minerals projects should be financially profitable, technically appropriate, environmentally sound and socially responsible'. In other words, the business of mining can only be sustained if these criteria are met.   Science and technology plays a major role in all four of these criteria. This paper will present the technology and innovation emerging from the Minerals Down Under National Research Flagship which brings together CSIRO and more than ten of Australia's leading universities to work with industry to drive efficiency, productivity and environmental performance. This work is required if the Australian minerals sector is to thrive and continue to deliver national benefit in the face of increased global competition, declining ore grades, depleting ore deposits, increasingly constrained national resources (land, energy, water and people) and changing societal expectations.   Science and technology to reduce emissions and water use, discover greenfields resources, enable deeper mining operations and transform mineral processing are described. Technology is presented as an enabler of sustainability: a means to this end but not as an end in its own right.

Jun 1, 2010

By C. M. Diaz, S. W. Marcuson

In the late 19th century, the discovery of rich nickel-copper sulfide ore bodies in Sudbury and the need for tonnage quantities of the metal to be used in nickel steel armor provided the foundation for establishing the Canadian nickel industry. For almost 50 years, International Nickel was the key player. In 1930, Falconbridge Nickel entered the field. These two companies remain the key Canadian nickel producers. This paper discusses the factors that have influenced the evolution of nickel smelting processes. The initial Sudbury ore smelting and nickel copper separation technologies were imported from abroad. It was only in 1937 that International Nickel established a process research laboratory in Copper Cliff The explosive post WW II industrial development created a strong demand for a broader variety of nickel products. For both International Nickel and Falconbridge, R&D became an essential business tool to succeed in the new market scenery. In the last few decades, new technologies were developed and commercialized to respond to the raising cost of energy, society pressing environmental concerns, the advent of nickel laterites as an important source of new metal, the incorporation of new nickel producers to the market, and, therefore, the need to increase productivity. Canada thus became an important exporter of technology. In this paper, the authors review this history with the objective of highlighting the forces that have triggered the most important changes in Canadian nickel smelting.

Jan 1, 2005

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

By J. T. Kalala

Energy consumption and wear of grinding media and liners are the major cost factors in milling plants. Since the beginning of the last century, much effort has been directed at the prediction of the power draw as affected by the mill operating conditions. This paper explores the prediction of the liner wear using the discrete element method (DEM). A mathematical model taking into account adhesion, abrasion and impact wear which occur in dry mills is derived in order to predict the loss of material on liners. The mathematical model is implemented in the DEM code using an objective function in order to produce realistic simulated profiles. Our DEM simulated predictions are compared to published experimental and industrial data. Keywords: modelling; discrete element method; liner wear

Jan 1, 2004

By R. Mier

The metals and minerals mining industry has evolved dramatically from the earliest objects ever made out of native copper circa 9,000 BC to the modern developments we see today. To better appreciate past developments and to get a sense of where the industry is heading, a brief overview of mayor industry highlights over the last 100 years will be presented, followed by a discussion on potential global scenarios and by a review on mayor industry trends.

Feb 27, 2013

By Juan Lucero

Como consecuencia de los factores externos e internos, las empresas mineras necesitan ser más eficaces a través de la implementación de nuevas tecnologías e informática. En este sentido, la compañía minera Milpo disminuye los costos de hardware para así generar un control de operaciones más minucioso, automatizado y oportuno. Los principales logros obtenidos son el control detallado de las operaciones, los sistemas operativos son la base para obtener los costos operativos, una mejor formulación y control presupuestal, control de servicios de terceros y el de los sistemas integrados.

Sep 13, 2001

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By Panfeng Gou

In order to solve the problems of supporting the roof of the gateroads affected by a fault, the movement characteristics of roof strata must be fully understood. In this paper, a plane stress physical simulation model was constructed to study roof strata displacement and deformation of gateroads driven in the hanging wall of the fault after the coals in the footwall were extracted. The results indicated that, due to the effect of fault, vertical cracks, orienting parallel to the dip of the fault, occurred in the horizontal direction of the model within the areas affected by the fault. The roof strata are discontinuous. On the other hand, non-uniform subsidence of roof strata occurred due to the bedding plane separation in the vertical direction. Roof strata, especially the lower roof strata, dip toward the fault. Failure of the surrounding strata is not symmetrical with the roof and floor close to the fault being deformed severely. In the selection of type of supports for the gateroads, the U-shaped steel supports are superior to roof bolting.

Jan 1, 2006

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

Rutile – Zircon Mining on East Coast Surfing Beaches – Rutile-Zirconium Producing Companies in Australia

Jan 10, 1964