Search Documents

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By Aleksandar D. Bugarski

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

May 1, 2007

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Grafton Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by rite in Metallurgical and Chemical Engineering for January, 1915. CAST-IRON TEST PLUG, SHOWING LOW MOTTLED AND MOTTLED FRACTURES. Several years ago, while I was thief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in befit open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the sill on ill every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 10, 1915

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

By R. Gallinger, B. Kelley

"In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale.The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP’s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed assufficient justification for the formation of INAP.INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage.This paper will explore the international efforts and activities of INAP."

Jan 1, 2005

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947