Search Documents

By Gerald C. Smith

Introduction Newmont Mining Corp.'s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By Charles E. Whieldon

Data on the oilfields in Mahoning, Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

By J. V. Batty

Radioisotopes of selenium (se78) and tellurium (Te123) were successfully employed by the Bureau of Mines as tracers in metallurgical research directed to developing improved methods for volatilizing these elements from low-tenor raw materials. Prior research, guided and controlled by conventional analytical methods, was seriously hampered by inconsistent selenium and tellurium analyses, by the slowness of the conventional chemical methods, and by the poor accountability of these volatile elements in test products. Methods were devised and evaluated for admixing the radioactive tracer with typical raw materials and then following the deportment of the selenium and tellurium by radiometric methods with occasional chemical analysis checks. These techniques were found unusually effective in (1) quantifying the completeness and the rate of volatilization of selenium and tellurium while heating the raw materials at different rates to different temperatures and (2) accurately tracing and quantifying the distribution of minute amounts of these volatile elements in the several products made by high-temperature treatment and in the several units comprising the experimental equipment.

Jan 1, 1962

By J. M. Ortiz

This paper shows the usefulness of geostatistical conditional simulation combined with the quantification of sampling errors obtained from the analyses of fundamental errors ? validated from duplicate data ? to assess the relevance of the quality and quantity of the information, for short-term mine planning purposes. Traditional blast-hole drilling equipment has been designed for efficient drilling, but not for obtaining high-quality samples. Furthermore, blast-hole sampling interferes with production, and thus usually produces poor-quality results. These results are the basis of short-term plans, where the grades of selective mining units are estimated and used for distinguishing between ore and waste. Under these conditions, misclassification (ore blocks sent to the waste dump and waste blocks processed at the plant) is inevitable, leading to significant hidden losses that can amount to millions of dollars per annum. Reverse circulation drilling with the latest automated sampling technology improves significantly the quality of the information used for short-term planning, and thus reduces misclassification, improving the financial returns of the operation. In this paper, we present the general methodology for assessing the effect of poor blast-hole sampling, as compared to advanced reverse circulation drilling grids at several spacings, in order to arrive at the most appropriate grid for short-term planning. This plan can be prepared well in advance using several additional variables that are usually not available when the plan is based on blast-hole samples. Furthermore, blending options can be analysed in order to optimize plant recovery, minimize the use of sulphuric acid, etc. Three case studies are presented, namely a typical porphyry copper deposit, an exotic oxide copper deposit, and a complex gold deposit, where mineralization is controlled by structures and lithology. This paper shows that in all cases, advanced reverse circulation drilling grids provide good-quality information that, coupled with the use of geostatistics for short-term mine planning, significantly improve the financial returns of the operation.

Jan 1, 2014

By J. C. HEILMAN

THE Tri-State district, named from its situation in three States, lies in the northeast corner of Oklahoma, the southeast corner of Kansas and the adjacent part of Missouri east of the common corner of the above States. Production in the past eighty years has come from scattered mines within an area of some 35 miles east and west, by 25 miles north and south, although the actual area of the mined ground is but a small fraction of this territory. The land is leased from the individual land-owners, and the size of the tracts varies from 4.0 to 200 acres, the smaller sized tracts predominating. The leases usually call for a royalty of 7% to 15 per cent of the gross receipts of the concentrates, continuous operation during the life of the lease and specifically set out that no ores can be brought in from a foreign lease for custom milling nor can any ore be removed from the lease for milling. The ownership of the tailings remains with the land-owner.

Jan 1, 1931

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

By B. J. Moore

This publication contains analyses and related source data for 675 natural gas samples from wells and pipelines in 24 States and 5 foreign countries. The samples obtained and analyzed during calendar year 1980 are included in tables 1-4. Those samples included in tables 5-7 were collected during the years 1960 through 1979. However, permission to publish the analyses of those samples was not given until the past year when the operators were again contacted to seek release of the information. All of these samples were collected as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576. The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-two previous publications have presented the results of 12,152 gas analyses made prior to 1980. The first three, Bulletins 486,' 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1980. The other

Jan 1, 1981

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

Owing to the number of chemical processes now in use for the separation of metals from their ores, and the consequent employment of chemicals at the mine, it is sometimes necessary to be able to produce them on the spot. This particularlyapplies to sulphuric acid which may be required for the manufacture of chlorine and of sulphate of copper, or for the treatment of'sulphides and other purposes. It can be made from brimstone for rather less than £3 per ton, but when delivered to any distance from the works, the cost of packages and other charges would amount to more than the value of the acid.I hope therefore, that to any of the members of the Institute who may find it necessary to make sulphuric acid for their own requirements an outline of the process, and some details of the plant etc may be useful, and perhaps lead to their devising improvements, mechanical or otherwise. Though acid can be made from pyrites in Europe for about 15/- per ton, it is probable that for most metaIIurgical purposes the quantity required. and the uncertainty as to how long it would be needed, would make it advisable to spend as little as possible on plant, and so use brimstone, though more expensive, I have therefore given no details of pyrites burning, which is very fully treated by Prof, Lunge in his work on " Sulphuric Acid and Alkali."

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By R S. Hamilton, S R. Grobler, M E. Greenway

The progressive development of underground mines frequently requires increased ventilation flow rates through mine shafts that were originally designed for lower rates. Where these shafts are equipped with conveyances running on rope guides, the higher air flow rates adversely affect the lateral motion of conveyances and could cause conveyances to collide with the shaft walls or with one another. Hence the safety impact of higher flow rates requires proper assessment. This can be undertaken by use of computer simulation models to predict the dynamic motion of the conveyances during hoisting. It can also be undertaken entirely by field testing, or using a combination of simulation and field testing. This paper discusses these techniques and makes cautionary remarks about setting an absolute generic maximum flow velocity for all shafts. Approaches to assess existing shafts for increased ventilation flow rates are also discussed.CITATION:Greenway, M E, Grobler, S R and Hamilton, R S, 2017. Safety impact of increased shaft ventilation on rope guided conveyances, in Proceedings Australian Mine Vent Conference 2017, pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By James H. Dye, N. E. Norman

There will be about 300 raise boring machines used worldwide by late 1981, attesting to the acceptance of this drilling system by the mining and construction industries. Over the past few years, many articles have cited the advantages of raise boring: •improved safety; •faster completion of the raise; •elimination of sublevels; •cost reductions; •better structural characteristics of the opening; •labor reduction; and •noise abatement. The relative importance of each advantage varies from mine to mine. When analyzing the total economics of raising, each advantage must be considered. The factors having the most effect on economics are fixed costs, direct costs, and comparative savings versus conventional methods.

Jan 3, 1981