Search Documents

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By S McKinley, S Juras, E Uludag

More and more, today’s mining geologists are asked to identify and create 3D value domains for multidisciplinary usage: grade definition, geometallurgical performance and geotechnical characteristics, to name a few. Often, that domain shape is the result of an assumed or conjectured value as a surrogate to a set of conditions (eg kaolinite-rich, sericite alteration). Would it not be instead better to create the respective domain through identification of a consistent quantifiable geologically-based pattern as its basis?Critical to the identification of patterns is the transformation of 3D point data into a model by a method that uses few, if any, preselected thresholds. Too often we complicate the reviews of the modelled data by prejudging the value range of interest. And when we do revert to 2D views (ie sections and plans), we tend to only examine numbers or line traces. These hinder and obscure identification of geological patterns particularly in deposits of complex geology. Instead, these data should be looked at with minimal prejudgment and interrogated in 2D space by one of the best and most eye-catching display types: filled contour plots.Here we present two different processes that transform data with minimal preselection into formats that allow for pattern recognition by filled contour plots. These are: probability assisted constrained kriging (PACK) and multiple interval interpolant formation (Aranz Geo’s Leapfrog® software). The former creates a 3D model of probabilities on a threshold value; the latter creates numerous (=10), regularly-binned 3D interval interpolants. The results of each method are examined as filled contours over numerous sections or plans. Any distinct patterns are quickly discerned thereby readily identifying the best value to base the creation of a domain. These processes therefore provide a way to marry recent advances in software tools with what is supposed a geologist’s core skill: pattern recognition.CITATION:Juras, S, McKinley, S and Uludag, E, 2017. Pattern recognition in transformed data – the search for domain shapes in mine geology data, in Proceedings Tenth International Mining Geology Conference 2017, pp 37–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

For tax purposes a mining company is a New Zealand company whose principal source of income is from the business of mining, or exploring for certain specified minerals in New Zealand. New Zealand tax law distinguishes between a non-resident mining operator and a mining company, with the only major difference in tax treatment being the corporate tax rates. New Zealand mining companies are taxed at 28 per cent, whereas non-resident mining operators are taxed at 33 per cent of taxable income. These provisions also apply to the petroleum mining industry. Individuals who carry on the business of mining are also specifically defined in the Act. They are termed as 'resident mining operators'. Non-resident mining operators are non-residents of New Zealand who carry on mining ventures as a business in New Zealand. Mining ventures are defined as the exploring, searching and mining of specified minerals, including development work carried out for profits. Similar provisions apply to the petroleum mining sector. Specified minerals are defined in the Income Tax Act 1976 ('the Act') and while no useful purpose is obtained by listing them in the paper, they include a larger number of industrial and commercial minerals. The Minister of Finance is also empowered to add to the list by publishing his determination in the Gazette.

Jan 1, 1988

Leadership "Organizing a group of people to achieve a common goal" Paradigms ? Rush to produce or cut costs. ? The most important thing after safety is production. ? We?ll take care of ??this?? once in production. ? I know what to do, 30 years of experience in mining. ? I want a 100% reliable operation.

Aug 1, 2013

By P Wood

Loy Yang Power (LYP) owns and operates a 2160 MW brown coal fired, base load power station in the Latrobe Valley, Victoria, Australia (Loy Yang A). It also owns and operates a brown coal mine that supplies fuel to its own power station and a nearby 1000 MW power station owned by International Power (LoyYang B). The mine supplies 32 Mt of coal per annum from an open pit, which is currently about 4 km long by 2 km wide and 180 m deep. LYP has 500 employees and a substantial amount of work is also carried out by contractors and consultants. GHD Pty Ltd(GHD) has been contracted to provide mine planning and earth sciences expertise. GHD is an international professional services company that operates globally in many market sectors including mining, industry and the environment. The company has major offices in Melbourne and also within the Latrobe Valley. This paper sets out the experiences that GHD and LYP have gained in establishing a unique alliance arrangement for GHD to provide a range of mine planning, earth science, dam surveillance and environmental services to LYP. The underlying philosophy of the alliance is to closely align the objectives of the two companies such that GHDÆs recompense for service delivery is proportional to the benefit achieved by LYPÆs business. Quality of service, whole of life costs and risk management are important aspects and are reflected in key performance indicators against which GHDÆs performance is measured. Currently GHD provide 20 000 hours of labour to LYP per annum, which are delivered by up to 120 staff who possess the required diversity of skills. The paper explains how the contract was initially let as a conventional service agreement and explains why the contract was transformed into an alliance. It then illustrates the operation of the alliance with reference to the 2006 work program. The paper concludes with thoughts on how the arrangement can be further developed for the future to the benefit of both parties.

Jan 1, 2006

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By Narendra N. Khatri, Michael Deutscher, Jozef F. Zurawski

Five sewer connections were required to divert Combined Sewer Overflow (CSO)from existing outfalls to an old underutilized large diameter brick sewer (the Easterly Interceptor). The connections were part of an on-going CSO control program by the Northeast Ohio Regional Sewer District (NEORSD) in the City of Cleveland, Ohio. Each connection was made by pipejacking and hand-mining a fiberglass-reinforced polymer (FRP) pipe through soft glaciolacustrine clays and silts. Jet grouting was utilized to stabilize the soils and fill the voids surrounding the interceptor prior to making the underground connection. Reinforced concrete liners were constructed inside the aging brick sewer to provide structural stability during ground improvements and connection work. The project also involved micro tunneling two approximately400 foot lengths of FRP pipe through soft ground using a slurry pressure balanced machine.

Jan 1, 2005

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

By Dave Bulled, Chris Bennett, Glenn Kosick, Glenn Dobby

"Mining companies around the world are embracing geometallurgical modeling at a rapid rate, as senior executives realize that inputs must be properly measured if the output is to be managed effectively. Geometallurgical modeling is used to scientifically manage risk in project evaluation, for plant design and production forecasting, and optimization of production planning and mineral processing/metallurgical unit operations. The technology also provides a solid foundation for implementing broad corporate strategies with respect to intelligent asset utilization and metal sales. Over the past five years, MinnovEX Technologies Inc. has been actively engaged in developing, promoting and applying geometallurgical modeling technology for major mining companies around the world. This paper describes the methodology for successfully applying the technology for the unit operations of comminution and flotation in the mining industry.INTRODUCTIONGeometallurgical modeling (referred hereon as geomet modeling), in theory, can be applied to its full potential on all unit operations in mineral processing; however, this paper will concentrate on two of the largest unit operations, namely comminution and flotation, where the technology is actually being practiced by many large mining companies. For concept studies and prefeasibility studies, aspects of geometallurgical technology are regularly applied but in a less rigorous manner than for final feasibility studies where justification for funds is sought. This paper will focus on the final feasibility stage of a project and on existing operations or planned expansions, where the full power of geometallurgical technology is brought to bear in a cost effective manner.One of the unique aspects of geomet modeling, when used to its potential, is the ability to design plants, and forecast and plan production with a quantifiable degree of precision, something that was unattainable in the past. This means that when new comminution and flotation plants are designed, the mining companies and financial institutions involved in the project can measure the precision of the design and therefore better understand and manage project risk. It means that for existing and new operations, metal sales personnel can carry out their sales strategies with a much better understanding of the degree of error associated with production forecasts of concentrate/metal and quality of concentrates. For mine and mill managers, geomet modeling allows the effect of the mine plan on the downstream processes to be quantified; thereby allowing the mine plan to be recast in a more optimized manner. Finally, existing concentrator personnel can optimize their unit operations based on a more definitive understanding"

Jan 1, 2004

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By J. O. Marsden

Over the past eight years, Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold, Inc.) devoted a significant amount of effort to the development of a suite of processes for the effective hydrometallurgical treatment of copper sulfide concentrates. This effort resulted in the development of high-temperature (>200ºC) and medium-temperature (150° to 165ºC) pressure leaching processes. Specific configurations of both processes have been commercially demonstrated at Phelps Dodge?s facility in Bagdad, Arizona. This paper reviews in detail the chemistry of medium-temperature pressure leaching of copper concentrates and reports on the process development work conducted by Phelps Dodge and others for this technology. This paper is Part I of a four-part series on this technology. Part II covers the development of medium-temperature pressure leaching and direct electrowinning technology; Part III considers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007