Search Documents

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By E. H. Chown

Scattered outliers of the Chibougamau Formation and the more continuous Mistassini and Otish Groups lie unconformably on an Archean basement abutting the Grenville Front. All the Aphebian rocks are deformed and offset by faulting related to the Front. The older Chibougamau Formation is exclusively elastic in origin, whereas the two later, time-equivalent groups include carbonatedominated (Mistassini) and elastic (Otish) sequences. Known syngenetic mineralization within these formations is limited to various radioactive showings in the Mistassini and Otish elastics, and the iron formations of the upper Mistassini Group. Three distinct types of epigenetic mineralization occur within the sedimentary rocks; pitchblende fracture fillings in all types of rocks in the Otish Group, widespread Mississippi-Valley type galenasphalerite showings at certain levels in the Mistassini Group, and chalcopyrite-pyrite bearing veins in or near argillaceous horizons of the Mistassini Group and Chibougamau Formation. The Otish elastic basin is part of a large area of the central Ungava peninsula which contains a variety of radioactive showings, the most promising being of the unconformity type, The final control for many individual showings appears to be local physico-chemical changes within faults and fracture zones. The overall structural control is in part supplied by the faulting episode related to the Grenville Front, which in turn limits the mineralization to the depth zone appropriate for open fracturing. The lead-zinc showings exhibit a strong stratigraphic control as well as close ties to secondary porosity developed by f aulting. The ore solutions were probably derived during the low grade metamorphism of the formations. Chalcopyrite- pyrite veins have provi ded the only mine production (Icon Mine) to date. They appear later than the low-grade metamorphic fluid circulation, and deposition is related to favourable structures and stratigraphy. The veins are clearly related to major faults. Thus, whereas stratigraphic settings appropriate to individual types of deposits are important, an overall structural setting may be demonstrated for a wide range of mineralizations. Detailed structural interpretations of individual showings may be the most fruitful pursuit in developing a concrete prospecting model.

Jan 1, 1984

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By M. England

A method for the analysis and prediction of single pile displacement behaviour is described. It is the displacement in time, under constant load, based on the use of hyperbolic functions to characterise individual constituents of the displacement-time behaviour. Extensive use of this technique has confirmed its validity in a variety of soils and that consolidation and creep settlement appear to be indistinguishable. The algorithms employed are suitable to model the displacement behaviour from the onset of load to infinite time for all types of piles and surface foundations. Until the advent of computer controlled static load testing, analysis of the displacement-time characteristic during pile load tests has been hindered by the quality of the data recorded and inconsistency of loading. This has hitherto made the development of suitable behavioural models very difficult. Understanding the soil deformation within a proper time framework allows the subject of pile instrumentation and testing to be developed. The equipment required is basically a computer controlled loading and pile head displacement measuring system which allows accurate analysis of the settlement characteristic in almost every situation.

Jan 1, 1993

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009