Search Documents

By K. B. Higbie

The quantitative separation of tantalum from columbium has been obtained through several liquid-liquid extraction processes. The valuable metals are separated by selective extraction from organic feed solution using a mineral acid or by selective extraction from aqueous feed solutions employing an organic solvent. The greatest degree of separation was obtained when organic ketones, particularly methyl isobutyl ketone, were used. Approximately 200 combinations of various organic solvents and mineral acids were tested as possible separation systems in which the tantalum or columbium content was extracted from organic solutions of the anhydrous pentachlorides.

Jan 1, 1956

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By D Chappell

Coromandel Peninsula gold mineralisation has an epithermal style which involves extensive alteration of host rocks and addition of pyrite over large volumes of rock. These altered rocks therefore have high potential for generating acid rock drainage. Natural acid groundwater discharges occur in altered rocks, but not in propylitically altered rock. There is little calcite available in mineralised rocks to neutralise this acid. In contrast, the mesothermal veins of the Otago Schist cause little alteration of the host rock, and that alteration has similar mineralogy to the host rock. Calcite is a common mineral in host and mineralised zones, and sulphides are generally subordinate. Hence acidification of Otago rocks is unlikely. This lack of acidification in Otago facilitates arsenic mobility in solution, up to hundreds of ppm. Arsenic is insoluble under acidic conditions in the Coromandel. Base metals are soluble under acidic conditions of the Coromandel, but they are immobilised by adsorption on to the widespread clay minerals where the solutions are neutralised. Base metals are generally immobile in Otago, but when they are mobilised, adsorption is less effectiveas an attenuation mechanism because clay minerals are rare.

Jan 1, 1998

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By C. E. Wood

Because of the renewed importance of the strategic metal manganese the Bureau of Mines in conducting further research on pyrometallurgical methods of beneficiating manganiferous iron ores and low-grade manganese ores. Published data on the Pyrometallurgical of manganese ores have been reviewed by Joseph.5/ A method of treatment that has received less consideration than others is the matte smelting of manganese or the separation of manganese from the iron and the gangue in an ore b, formation of a matte, that consists principally of esulfide of manganese. A procedure of this type has been patented by Betts.6/ Lofquist7/ claims advantages for the production of a sulfide-oxide matte as a method of recovering manganese in alloys containing manganese and iron.

Jan 1, 1940

Performance of Outotec FloatForce« Flotation Mechanism - A Study in Both Computational Fluid Dynamics and Industrial Scale Measurement

Sep 13, 2010

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

Research personnel from the Bureau of Mines, a representative of the Mine Safety and Health Administration, and research contractors for the Bureau of Mines met with other Government and industry representatives at three seminar locations in December 1980 to discuss the findings and products of Bureau research on mine safety training. The research program is aimed at providing assistance to the mining community in its efforts to reduce industrial-type, human-error accidents through research establishing performance based methods and media for employee training. Research emphasis is directed toward development of baseline materials and instructional models; development of methods for structuring and evaluating health and safety, supervisory, and occupational training; and the continued investigation and application of current learning and simulation technology that could significantly enhance the effectiveness of training opportunities.

Jan 1, 1981

By M. Heger

February 2, 1999 marks a milestone in earth-moving technology at the San Miguel Lignite Mine. It was on that date that The North American Coal Corporation (NAC) took delivery of three Leica Dozer 2000 GPS grade control systems for use on its bulldozers. The primary reason for the purchase of these grade control systems was to prove that GPS technology could safely and economically be utilized on heavy equipment to assist operators in defining grades. If these properties were successfully demonstrated, the ultimate vision of the project was to expand the system to a point were GPS would become the primary means of providing grade control information to the mine’s heavy equipment operators. Twenty nine months and more than $500,000 later this vision was realized when the final bulldozer operating at the San Miguel Lignite Mine was equipped with Dozer 2000. Presently North American Coal has a total of nine Dozer 2000 GPS grade control systems at San Miguel providing cut and fill information to operators 24 hours a day. These grade control systems have allowed the San Miguel operation to increase safety, reduce costs, improve operator attitude, and better ensure environmental compliance. This article discusses both the nature of these benefits and some of the issues that had to be dealt with along the way.

Jan 1, 2002

By Gray Mullins

A post grouted drilled shaft foundation system was successfully used in place of the specified driven pile foundation system as a Value Engineering Cost Proposal (VECP) for the new PGA Boulevard Grade Separation Project. Pressure grouting the cohesionless sandy soils at the drilled shaft base significantly increased the end bearing capacity and stiffness allowing drilled shafts to be the more cost effective foundation system. The post grouted drilled shaft option also provided other benefits including reducing owners risk normally associated with pile driving vibrations and offered a high level of quality assurance for the drilled shafts. This paper discusses the implementation of post grouted drilled shafts from design to completion of construction. A design procedure for post grouted drilled shafts developed by the University of South Florida was used for initial VECP evaluation. Prior to construction, two instrumented test shafts were installed and load tested, one of which was post grouted. Therein, the design procedure was calibrated, tip elevations for production shafts were refined, drilled shaft construction and grouting procedures were demonstrated, and a grouting criteria was developed for the project.

Jan 1, 2003

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991

By F. T. Cawood

This research report was produced in response to the release of the Mineral and Petroleum Royalty Bill. It involved are view of the mineral investment environments of selected countries in order to form an opinion on the appropriateness and competitiveness of the proposed royalty structure for South Africa. Many emerging countries have recently attracted a significant share of foreign investment, as a direct result of changes in policy. These are, by implication, the least risky and most favourable destinations for the ?investment dollar?. The five most competitive countries, namely Chile, Argentina, Peru, Mexico and Brazil have been identified as succeeding with their policy visions of creating favourable domestic investment environments. The investment rules of these countries served as a basis for the compilation of a Competitive Investment Framework (CIF). This is a template of best practice against which other investment environments, such as that of South Africa, can be measured. The framework indicates that mineral royalties should ideally be no more than three per cent, demonstrating that the regime proposed in the Royalty Bill is out of step with international best practice. Mineral royalties can never be viewed in isolation and in the assessment of the rates proposed in the Royalty Bill, one must consider the total taxation package. Such assessment appears in Section 5 of this report, demonstrating that there is reason for concern if National Treasury were to impose the rates stipulated in the Royalty Bill. The alternatives, conclusion and recommendations of the review appear in Sections 9 and 10. These are the result of independent analysis and assessment of the fundamental principles. It is done through the application of a Competitive Investment Framework that avoids the highly subjective and emotional views that often accompany a process like this.

Jan 1, 2003

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0·9 dwt., whilst for average to high-grade ore, 3·5 to 5 dwt., the figure was 1·5 to 2·0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months' research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company's workshop.

Jan 1, 1939

By Fred D. Fox

Introduction Abandoned mill tailings deposits can be found throughout the northern Black Hills of South Dakota, indicative of mining activities that originated during the great gold rush days of 1875. The Refuse Act of 1899 attempted to regulate the deposit of debris from mines and stamp works. But, in most cases, huge volumes of mine and milling wastes were disposed of in ways no longer considered environmentally acceptable. Restoration of gold mill tailings deposits is a relatively new practice to the Black Hills area. This discussion will present an overview of the environmental setting, environmental problems associated with past tailings disposal practices, practices being implemented to solve these problems, and prospects related to present the future tailings disposal practices. Environmental Setting An understanding of climatic characteristics, geology, surface and ground water hydrology conditions, and the physical and chemical characteristics of selected mill tailings deposits will aid in understanding environmental problems associated with tailings disposal and restoration. Climate The Black Hills region is in the middle latitudes, which have a

Jan 11, 1984

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000