Search Documents

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974

By Dean Brox

The Galore Creek Mine project is one of the newest major mining projects under development in Canada. The project is located in a very remote area of northwestern British Columbia and is being developed by NovaGold Resources and Teck-Cominco of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site a new 120 km road is required including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipe-line. Structural portal canopies and portal houses have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works have commenced prior to any other works at the mine site and will be constructed entirely by helicopter support. The tunnel works commenced in the summer of 2006 with the advanced excavation of the overburden materials at the portals. Tunnel construction from the North portal commenced in the spring of 2007. When completed, the mine access tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed along with a construction status update as of late 2007.

Jan 1, 2008

By O. P. Hood, G. St. J. Perott, S. P. Kinney

"FOREWORD (By O. P. Hood, Chief mechanical engineer).During the war certain suggestions concerning power production were made by Mr. Walter E. Trent to the War Inventions Board, and at the request of the War Department facilities for experimental work were provided on the grounds of the. Bureau of Standards.The experiments were along the line of controlling the conditions of combustion in a closed space. In order to reduce slag troubles, experiments were carried out for removing ash from powdered coal. After the war, work along this line was continued, resulting in the Trent Process, which agitates or beats together powdered coal, water and oil.A new technology had previously been given to ore preparation by the use of small quantities of oil in water with froth flotation, and although the methods, results and mixtures of the Trent Process were quite different, yet the same physical phenomena of differential wetting used, and the possibility of there being interesting results in fuel technologic was evident. A cooperative agreement was entered into, whereby the Bureau of Mines was to investigate the underlying physical and chemical facts and make them public, and the Trent Corporation was to pay the cost of the investigation.The several reports as made have been available to any one interested, and are now to be published. While the Bureau of Mines felt justified in investigating the physical phenomena so far as might be done in a laboratory, and so far as public interest might reach, no attempt was made to discover the commercial possibilities which development might bring. The question of commercial possibilities must be left for commercial enterprise to answer."

Jul 1, 1921

By L. Schernikau, W. H. Smith

Oil, coal, and gas account for approximately 80% of global primary energy, but only a portion of total airborne CO2 eq (approx. 35% at GWP20 to 65% at GWP100), even though they account for 95% of total measured CO2 emissions. The benefits of these energy sources, as well as their related costs, are not all incorporated in current energy policy discussions. Global greenhouse gas policies must include documented changes in measured airborne CO2 eq to avoid spending large amounts of public funds on ineffective or sub-optimal policies. The authors examined airborne CO2, which is less than half of emitted CO2, as well as reported CH4 emissions and the global warming potential of CH4 as published by the IPCC for coal and natural gas. The surprising conclusion is that surfaced-mined coal appears ‘better for the climate’ than the average natural gas, and all coal appears beneficial over LNG. Therefore, current CO2-only reduction policies and CO2 taxes are leading to unintended consequences and the switch from coal to natural gas, especially LNG, will not have the desired impact of reducing predicted future global warming; in fact, quite the contrary. A large portion of anthropogenic global warming is attributed by the IPCC and IEA to CH4, but it must be noted that CH4 emissions from natural sources and from agriculture account for approximately 40% and 25% of annual global CH4 emissions respectively. Energy accounts for about 20% of documented CH4 emissions. CO2 contributes only approximately 35% of annual airborne anthropogenic GHG emissions after accounting for CH4, over a 20-year horizon. At a 100-year horizon, the contribution of CO2 increases to approximately 60%. Energy policies that do not consider all GHG emissions along the entire value chain will lead to undesired economic and environmental distortions. All carbon taxation and CO2 pricing schemes are incorrect and need to be revised. At IPCC’s GWP20 an approximately 2%1 higher loss of CH4 across the value chain prior to combustion of natural gas versus coal will lead to ‘climate parity’ of coal with natural gas. According to public data, natural gas value chains have high CH4 and undocumented CO2 losses. On a global average, using only IEA-documented CH4 data, natural gas emits approximately 15% more CO2 eq than surface-mined coal, over a 20-year horizon. This difference will increase as the use of shale gas and LNG expands. Investors should support all energy systems in a manner that avoids an energy crisis, including intermittent renewable energy systems where they make sense. If CO2 emissions need to be reduced, one of the most effective ways would be to install ultra-supercritical power plants with CCUS technology. However, the undisputed benefits of increased CO2 concentrations in the atmosphere because of its promotion of photosynthesis and plant growth effects (fertilization) need to be considered in energy policy decisions as well. The authors suggest that future research and development should concentrate on reducing net emissions from fossil fuel power plants and providing cost-effective and reliable new conventional power generation capacity, utilizing clean coal and clean natural gas technology.

Mar 2, 2022

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By C. E. Fivaz

SYNOPSIS Tribute is paid to J.S. MacArthur and the Forrest brothers for their invention. The opinion is expressed that the successful application of their process, not only saved the gold-mining industry on the Witwatersrand from stag¬nation for an indefinite but probably prolonged period, but also made a major contribution to the economic growth of the country in the twentieth century. A background is given of the activities of prominent chemists who researched the solubility of gold in cyanide solution prior to the MacArthur-Forrest invention. An account is given of the invention and patenting of the cyanidation process, and of the golden rule that the patentees laid down for themselves, which came close to wrecking the invention. The South African gold-mining scene from the discovery of gold on the Witwatersrand in 1886 up to 1890 is sketched. An account is given of how, when unoxidized ores were first encountered, the recovery efficiency dropped alarmingly, gold shares were sold on an unprecedented scale, and doom and despondency seized the town of Johannesburg. The complete turnabout in the fortunes of the South African gold-mining industry after the introduction of the cyanidation process in 1890, the steady rate of increase in production after the Anglo-Boer War, and its effect on the South African economy are described. A brief look is taken at the effect of gold mining on secondary industry. The deportment of the gold that is not dissolved from the ore by the cyanidation process is illustrated. Some thoughts are expressed on what can be done to increase the gold recovered by cyanidation.

Jan 1, 1988

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Scott Turner

The monetary metals , gold and silver , have recently been the object of such general interest that the United States Bureau of Mines has received many inquiries regarding them . Though requests for technologic information have been numerous , they have been exceeded in number by those concerned with economic aspects of these metals . The nature of the latter communications indicates that the public is not generally aware that various Bureau publications are available which deal with the economic situation of gold and silver . For this reason , it is deemed advisable to present a brief résumé of the papers which are obtainable from the Bureau or the Superintendent of Documents , together with the text of three articles recently prepared by the Director , reprints of which are not otherwise available . The Bureau of Mines compiles figures showing mine production of gold and silver , by districts and States , and cooperates with the Bureau of the Mint in determining the total annual output in the United States as a whole . 3 It recently established an annual canvass to determine the consumption of silver in the arts and industries of the United States , and published an economic paper covering such use in 1928 and 1929 , followed by an information circular on silver consumption by industry during the 2 years subsequent . A 4-year record is thus provided for those interested in utilization of silver . The Bureau has also published summarizations of all available data upon world production since 1493 of gold and of silver . It has , furthermore , rendered available a compilation of production- data of silver mines of the world , and an analysis of it , showing the proportions of silver and other metals contained in all the ores from which silver is derived . " All of these papers are concerned solely with putting into readily usable form statistical data and other factual material ; they do not offer theories or express opinions upon controversial questions related to these metals . Three other recent papers concerned with gold and silver are presented below in order to put them in shape for distribution by the United States Bureau of Mines . All three of them are by the Director of the Bureau . It should be noted that these papers do not commit

Jul 1, 1933

The Bega granite at Whipstick, N.S.W., consists of a granite metasomatically altered to leucogranites and a spessartite-granite. The ore occurs in pipes controlled by jointing and shows evidence of post-depositional tectonic forces.The principal ore minerals are molybdenite and bismuthinite, with minor amounts of uraninite, pyrite, gold, bismuth, joseite A, joseite B, tetradymite, chalcopyrite, arsenopyrite, and skutterudite. The gangue minerals are microcline, albite, quartz, muscovite, and spessartite, with fluorite, chlorite, magnetite, and biotite as accessory minerals.The intrusion of granite was followed initially by ascending metasomatic fluids which penetrated along joints to be trapped in the domed roof of the intrusion to form the leucocratic granite. Iron-manganese-rich fluids metasomatically altered the granite to a spessartitegranite which is associated with the later deposited ore.Quartz veins and dykes of varying composition post date the ore deposition.

Jan 1, 1968

By J. Guha, A. Gobeil, P. Pilote, A. Tremblay, E. Dimroth

The Mount Bourbeau Lac Berrigan area is located just to the north of the Town of Chibougamau. The axial trace of the Chibougamau syncline borders the northern part of both areas. The area contains Archean rocks of the Roy Group, intruded by the Cummings Complex and the Line Lake tonalite stock. Proterozoic sedimentary rocks occur in a series of outliers. Various Cu, Zn, Pb, Ag, Au and Mo showings are dispersed over the area in a wide range of time and space. Pre-Kenoran (stratiform and stringer) showings related to volcanic activity may be distinguished as well as the syn-or post-Kenoran (vein) types whose nature is imprecisely known. In this area, the stratiform showings occur in the Gilman and Blondeau Formations, whereas the vein type showings occur for the most part in fractures or breccias within or along the contacts of the various sills of the Cummings Complex. Mount Bourbeau is distinguished by the greatest variety of showings as well as the proximal volcanic facies of the Blondeau Formation. A volcanic centre is presumed to lie a short distance north or east of the locality. Locally, the Line Lake stock contains significant silver, molybdenum and gold mineralization. Its role as a metal reservoir, a source of heat for the circulation of hydrothermal fluids and its control of the local tectonic style remains to be determined.

Jan 1, 1984