Search Documents

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By Jacek Kolacz

A new sensor based sorting system has been developed, based on complex image analysis, where an image texture and a shape pattern is considered for identifying particles for separation. The sorting system employs different images generated by visual light and X-ray to provide maximal information about processed particles. Application of X-ray makes it possible to analyse the internal structure of the particles, which provides a 2D image with complicated texture, however, which contains valuable information. The advanced system for the texture and the pattern recognition is applied to analyse these images simultaneously, to provide the required identification of the particles for efficient separation. The mathematical models applied during identification and separation, are assisted by high speed calculations being specially optimised for this kind of process. This allows sorting with high capacity and high accuracy, which is critical for practical applications in mineral processing. The paper describes a number of tests during sorting of iron ore and coal with high separation efficiency.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By B. Csoke

To improve the efficiency of the crushing/screening plant of Bazalt-Középko Kobányák Ltd. (Hungary), the implementation of computer aided quality control is planned. In the current phase, the R & D work aims at the solution of high-priority tasks: 1) Developing the process models, validation of the models by means of industrial measurements. 2) Developing the algorithm for the process control of the crushing/sizing plant. 3) Developing the suitable computer program. To develop the mathematical models of crushing (breakage and probability functions) and to determine the model parameters, the experimental industrial trials were carried out on hydrocone crushers of types Svedala H 4800 EF and H 4800 F, changing the gap size and crushing relatively narrow grain size fractions. Additionally, the parameters of the separation function for the screens operating in the system were determined. It was established that the crushing probability depends on the grain size of the feed (Y) and the gap size (s), so the breakage probability S, for each cone crusher, can be well characterised by the function formed using the ratio of these two parameters: SfYsf==. The distribution of the broken grains can be described reliably using the relative grain size distribution function B(? = x/Y) (usually Schuhmann-Gaudin- or Rosin-Rammler-shaped function). For the screens, the probability function ()2()111/NTx = xd ???---???? is suitable for cha-racterising the separation (where x? grain size, ?-open-area ratio, d ? rectangular screen aperture size, N ? number of appearance of the particle on a screen surface). Using these functions, the comminution circuits were described by means of vector/matrix equations. The calculations and measurements verified the reliability of the developed models and algorithms.

Jan 1, 2014

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By X. Q. Cao

As the second largest phosphate resource in the world, Chinese phosphate ores generally grades with low of P2O5. The presentation of beneficiation test on the low grade of phosphate rock in this paper may be used for a reference for development and utilization of the similar reserves. The ore is a marine sedimentary phosphate rock containing low grade of P2O5 and high content of MgO and R2O3; The banded structure shows its suitability for heavy medium separation. The laboratory heavy liquid testing results indicate that as specific gravity of the heavy liquid is 2.85 g/cm3, a rougher concentrate assaying 28.71% P2O5 could be obtained while the rougher tailings contain only 4.47% P2O5. When the combined process with heavy liquid separation followed by direct & re-verse flotation is employed to treat the feed containing 21.15% P2O5, 3.79% MgO, 1.86% Fe2O3, 3.66% Al2O3, 23.75% A.I, and specific gravity of heavy liquid is 2.84 g/cm3, the optimum mesh of grind is 67.5% minus 200 mesh, a phosphate concentrate contained 32.51% P2O5, 0.48% MgO, 0.81% Fe2O3, 1.69% Al2O3 can be produced at a yield of 55.24%. The concentrate P2O5 recovery is 85% with which quality comply with the Class A specifications for production of phosphate fertilizer.

Jan 1, 2014

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By G. Y. Liu

The structure-activity relationships for four thionocarbamate collectors are discussed in this pa-per. These collector classes are alkyl alkyl thionocarbamates, allyl alkyl thionocarbamates, acyl al-kyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates. The main emphasis will be to highlight the differences between collectors and their affinities for copper and iron sulfide minerals on the basis of data on electronic-structure properties obtained by vacuum and solution density functional calculations, flotation experiments and analysis measurements. The mechanism of interaction of these collectors with sulfide minerals is also discussed with perturbation theory. The theoretical study results indicate that acyl alkyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates have best performance in these agents as flotation collectors with improved collecting power for copper sulfide minerals and excellent selectivity against iron sulfide minerals, which are consistent with the experimental data reported in the literature.

Jan 1, 2014

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

By G. C. He

Effects of irregularity, rough surface and aggregation of fine particles on ultrasonic attenuation are significant. The effects should be considered while predicting particle size by ultrasonic attenuation technology. The scanning electron microscope micrographs analysis also shows that particles surface is rough and irregularity. Any slurries has its fractal structure and its special fractal scale and dimension, so, effects of irregularity, rough surface and aggregation of fine particles can be de-scribed by fractal model. The discrepancies between predictions of ultrasonic attenuation based on the assumption of smooth spherical particles and data obtained from slurries of irregular particles indicated that there were different fractal structures. The ultrasonic attenuation model was modified by fractal dimensions. The result of experimental data and analogue calculation indicated that pre-dictions of the fractal modification of ultrasonic attenuation model show good agreement with experimental data. On the other hand, from the values of fractal obtained by inversely calculation, the degree of effects of irregularity, rough surface and aggregation of particles can be estimated. The positive value of fractal dimension indicates that the aggregation has the dominant effect on ultra-sonic attenuation, otherwise, the irregularity and rough surface has the dominant effect.

Jan 1, 2014

By M. H. Kotze, V. Yahorava

A gold-selective ion exchange resin, containing tributylamine groups, was developed by Mintek for the recovery of gold from cyanide leach solutions. The Dow Chemical Company and, more recently, Purolite commercialized the production of this gold selective resin for use in the gold mining industry, and it is marketed as Dow XZ-91419.00 and Purolite A194 respectively. A novel application of this resin is the selective recovery and separation of AuCl4 - f rom p latinum group metals (PGMs) in chloride and nitrate solutions. The current paper describes potential benefits of this type of resin for selective recovery and upgrading of gold from low grade chloride or nitrate waste streams, and the possibility of gold separation from PGMs during their refining in chloride media.

Jan 1, 2014