Search Documents

By G. A. Wierink

This paper discusses a new method to increase flotation recovery. As known from literature, fine and coarse particles have different flotation rate constants, hydrodynamic behaviour and require different reagent regimes. The device discussed allows separate processing of finer and coarser slurry by extraction of a third stream, carrying finer slurry, from the flotation cell. By separate treatment of fine and coarse slurry operational conditions and so flotation recovery for both may be optimized more efficiently. Extraction and classification of the third stream is accomplished by low speed centrifugation and Taylor-Couette flow separation. This Dual Outlet Device (DOD) can be installed in a traditional flotation cell without need for equipment replacement. In order to asses different design options for the DOD a transparent laboratory scale model was built. For this scale model Computational Fluid Dynamics (CFD) simulations using the RANS k-e and LES turbulence models were performed. Essential insight in the dominant flow systems relevant to optimal operation of the DOD was obtained from the CFD simulations and flow visualization tests with the laboratory scale model. Based on these findings a number of configurations were investigated at pilot plant scale in a 5 m3 Outokumpu flotation cell. The results of the pilot plant study show that utilization of the DOD provides a method for in-cell control over particle size distribution in the slurry. Use of the DOD in a flotation cell may enhance flotation recovery and decrease flotation reagent consumption significantly, against marginal investment and operation costs.

Jan 1, 2014

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By Michael L. Free

The hydrometallurgy curriculum for undergraduate students at the University of Utah has evolved to contain a variety of tools to help students understand and apply hydrometallurgy in a context that has industrial relevance. In order for students to perform as engineers in an industrial hydrometallurgy setting, they need to understand thermodynamic and kinetic fundamentals and be able to apply these fundamentals to extraction, concentration, and recovery applications. Students must also understand related environmental, economic, and assessment issues in hydrometallurgy and be able to work with others. In order to meet these needs, the hydrometallurgy curriculum includes a variety of relevant subject information, on-line resources, laboratory experiences, and team work opportunities to help prepare students for careers involving hydrometallurgy. The development and use of these resources will be discussed in this paper.

Jan 1, 2014

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By W. A. Hodgson

"In order to be able to map the variation in the concentration of elements in soils, it is necessary to sample at intervals that will give adequate coverage of the area and will allow determination of the rate of fluctuation of concentration with distance in any environment. This rate of fluctuation with distance can be referred to as the continuity of concentration.The continuity of concentration in soils varies according to the chemical characteristics of the element being considered, the underlying rock type or orebody and in response to the dispersion processes that operated during soil formation. Within any environment there is a maximum distance between sampling points within which adjacent sample values are related. This distance, the critical sampling interval, can be determined by means of a correlograrm.Where the sampling grid has been chosen to provide an adequate coverage over unmineralized rock, adjacent samples being related, anomalies may be missed if the element continuity in the anomaly is less than in the background. Results show that a knowledge of the critical sampling interval of the environment being examined may used to select a more efficient sampling pattern for a geochemical survey."

Jan 1, 2014

By Robert Hopler

In use, blasting powder is exploded by a spark from fuse, electric squib or miner’s squib, or by a primer of some high explosive, the last being employed only in heavy charges on open work. In mining, and sometimes in light charges on open work, blasting powder is made into cartridges by means of a paper tube or cylinder sealed at one end, which is known as the Du Pont tamping bag. Sometimes the paper cylinder is made by the miner by coiling a section of heavy paper, known as blasting paper, around a wooden pin, called a cartridge pin, and securing it with what is called blasting soap. The removal of the pin leaves a cylindrical cartridge open at one end, into which the powder is poured and the top folded and sealed with blasting soap.

Jan 1, 2014

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the present study, the dynamic response of AZ and AE cast magnesium alloys to shock loading, are compared for strain rates ranging between 900 and 1200 s-1. Texture measurements showed that after shock loading, the (00.2) basal texture component of both alloys was strengthened. However, the strengthening magnitude was higher for AE samples. Also, it was observed that the twinning fraction decreased in both alloys with increase in the amount of alloying elements. In addition, cracks are formed at the interface between matrix and second phase particles in the AZ alloys. However, crack nucleation and fracture in AE alloys occurred at the sites where twins accumulated. Furthermore, analysis of the dynamic mechanical behaviors showed that the ductility of AE grade is higher than that of AZ alloy for all strain rates used in this research. This difference was explained by differences in deformation mechanisms of these alloys.

Jan 1, 2014

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By Joram M. Amir, Ernst Niederleithinger, Nikolaus Schneider

"Abstract: Diaphragm walls are used to provide a stable and watertight confinement for the construction of tunnels, underground railway stations, deep basements and other structures requiring deep excavations. Water seepage and soil loss through the joints have occurred on several occasions, causing extensive damage. This may have been due to uncontrolled concrete flow between the joints, unexpected geologic conditions or just poor workmanship.Different ways of quality assurance are applied on construction sites. Most of them rely on recording parameters of the construction equipment and conventional concrete quality control. In the frame of the EUREKA/ZIM project DiWaQ we have looked at several ways to perform non-destructive quality control. Some methods are to be applied after excavation before concreting (phase 1); others after the wall is completed (phase 2).For phase 1 we have used two different principles for checking the shape of the excavation, especially the joint to existing panels. A mechanical device which can be adapted to the excavating equipment was developed; field tested and validated on test and construction sites. It is described in detail in another paper in the same volume. A sonar-based device with a 10 mm resolution has shown good performance in the lab, but is still under development.For phase 2 different temperature sensors have been lowered into access holes to monitor the hydration heat developed during concrete curing. The same tubes can also be used to perform electromagnetic and ultrasonic crosshole measurements across or along joints to detect flaws. Especially the ultrasonic method has shown promising results on validation specimen at the BAM test site at Horstwalde, but limitations as well. Success substantially depended on the joint type, flaw size and distance of the sensors to the joint."

Jan 1, 2014

By Tyler Ross, John Tatom, Lon Lantis

The Institute of Makers of Explosives (IME) began development of a Quantitative Risk Assessment (QRA) tool, IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk), in 2005 as a technology transfer effort with the United States Department of Defense (US DoD). Version 2.0 of the software has been developed over the last two years and introduces many new features and upgrades. Key upgrades include a new map-based user interface, new debris density hazard models, a metric version, and additional user options referred to as “conservatism switches”.

Jan 1, 2014

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

By Jing Zhang, Qing Xiao, Xulong Liu, Qiuju Li

"Pickling sludge generated from stainless steel production process contains large quantity of Cr, Ni, and Fe. The disposal of and fill sludge directly not only leads to the heavy metal dissolves in the soil and underwater, but also loss value metals. However, the major mineral phases of value metal are hydroxides and there are lots of calcium fluoride and water in the sludge. So the pickling sludge has to be pretreated before reduction-magnetic separation. The TG analysis, reduction reaction and magnetic separation were all used to study the pickling sludge. The result indicated that up to 900°C the total weight loss of pickling sludge was 22.32%. The mass contents of Fe, Cr and Ni in the tailings (non-magnetic) were 4.27%, 0.067% and 0.041% respectively.IntroductionSince 21st century, the stainless steel production in the world has been continuously increasing because of its excellent performance [1]. However, high stainless steel production means a high pickling sludge production. For example, in a stainless steel plant with waste water quantity of 100m3 /h, the production of pickling sludge will exceed 15 Kt/a. Pickling is essential for generating of a homogeneous and corrosion-resistant surface during stainless steel production subsequent process. Pickling of stainless steels is predominantly carried out with an aggressive solution, sulfuric acid H2S04 or composed of nitric acid HN03 and hydrofluoric acid HF [2]. During the pickling process, the pickling acids are recovered through ion exchange and metal ions such as Fe3+, Cr3+ and Ni2+ get into the acids forming the pickling waste water [3]. Then, the pickling waste water is precipitated with lime, forming pickling hydroxide sludge. It is not feasible to recycle or treat the pickling sludge using conventional methods, because the sludge has high contents of calcium fluoride and water but low contents of iron, chromium and nickel. However, it would also pose a potential environmental problem if deposited outdoors over a long term because it contains heavy metals such as Cr and Ni. At present, solidification/stabilization (S/"

Jan 1, 2014

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By A. S. Choudhary

India is endowed with a reasonably large reserve of chrome ore, amounting to about 100 million tons in different grades and is one of the leading producers of ore/concentrate along with South Africa, Kazakhstan and others. Chromite production in India has registered a 10 times increase during the last 30 years. Till late 1940s, the practice was to mine the high-grade ore for making ferrochrome and charge chrome and export the same leaving the low and medium grade ores stacked around the mine as waste material. This practice was continued for quite some time till the increase in world wide de-mand of chromite initiated an increase in production of chromite ore in India and the aspects of ?economy of operation? and ?conservation of mineral? dawned on the producers and associated authorities. Recovery of chrome values from low and medium grade ore was initiated to produce high-grade saleable concentrate. Suitable legislation was made by Government of India to induce and provide incentives to the operators to do so. First large scale chromite beneficiation plant in India was commissioned about three decades back at Byrapore in the Southern state of Karnataka. The ore, rather simple in nature and relatively free from clay, was obtained from underground. The processing consequently was simple washing and wet tabling. Further more, some test work, on the samples from eastern coast particularly from Orissa, was carried out at an internationally reputed laboratory by a large private operator and the plant was set up. This consisted of a combination of crushing-grinding-de-sliming-classification followed by concentration in multi stage spiral concentrators and shaking table. The plant was commissioned and operated successfully. Soon a state owned company followed suit on the basis of test work carried out in a well equipped Indian laboratory. The plant worked satisfactorily after some initial teething trouble and the company plans to double the existing plant capacity by installing balancing facilities. This development prompted a number of operators, including industry leaders to join the fray and the chrome ore processing industry flourished in India. More and more operators are now in the process of adding capacities to their existing plants. This paper attempts to chart the evolution of chrome ore beneficiation industry in India through a case study with reference to an existing plant. The process technology adopted and modified to suit the altered requirements as well as the future trends are outlined.

Jan 1, 2014

By Baokuan Li, Qiang Wang, Zhu He

"A mathematical model has been developed to investigate the magnetohydrodynamic (MHD), thermal, and solidified behavior in electroslag remelting process. Based on the finite volume method, a multiphase coupling MHD approach is employed to investigate the droplet formation as well as movement in molten slag under the action of an alternating current. The VOF formulation is adopted for interface tracking. The electrical potential method is adopted for the electric current and magnetic field. The Electromagnetic force and Joule heating are recalculated at each time step and then is implemented in the momentum and energy equations as a source term, respectively. Moreover, solidification of the metal is described by an enthalpy-based formulation, while the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The model is used to investigate the effect of electrode tip shape on MHD, thermal, and solidified behavior and provide valuable information.IntroductionElectroslag remelting (ESR) process has been used widely to produce high-performance alloys dedicated to critical application, such as hot work tool steels, nickel base alloys, the manufacture of components in aerospace and landbased turbines, etc. Figure 1 shows a schematic diagram of ESR process including a consumable electrode, a molten slag pool, a liquid metal pool, a solidified ingot, and a water-cooled mold. Alternating or direct current flows from the electrode to the water-cooled baseplate through the high resistivity calcium-fluoride-based molten slag which result in Joule heating and Electromagnetic force (EMF). Part of the Joule heating melts the electrode and the droplets travel through the slag and accumulate the liquid metal pool. The electrode is continuously advanced into the slag as it melts to build up an ingot of improved structure and composition by controlled solidification and chemical refinement. The metallurgical properties of the remelted ingot are really related to the solidification structure, which strongly depends on magnetohydrodynamic, thermal, and solidified behavior in the molten slag, liquid metal pool, and mushy zone."

Jan 1, 2014

By C. B. Yu

The ore comprise of chalcopyrite, valleriite, pyrite, pyrrhotite and so on. Serpentine and talc are chief gangues. Copper phase of the tail shows that mostly valleriite be losed in tail, 70% mineral of copper is valleriite in tail, so severity reduce the recovery of copper. The traditional flow-sheet in acidity mine pulp to flotat the valleriite, but copper-sulphur separated in high alkaline pulp, so the valleriite be losed else. Explores the characters of the valleriite?s surface, studys on the flow-sheet of flotat valleriite and copper-sulphur separated. In neutral mine pulp, adopt of cationic collector to flotat valleriite, adopt of hyposulphite to depressant pyrite in low alkaline pulp can advance the recovery of copper to 5.06%.

Jan 1, 2014