Search Documents

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By John Stubbles

Data are presented on the global warming issue to reinforce the decision by the U.S to reject the Kyoto protocol. The evidence that CO2 is a problem rather than a benefit is inconclusive and will be discussed in this paper. Nevertheless, for economic reasons alone, the US steel industry will continue to minimize CO2 emissions (and the release of real pollutants) per ton of steel through energy reduction programs. However, relative to inevitable increases in absolute CO2 emissions from the utility industry and the transportation sector, future reductions by the steel industry will be inconsequential in the "big picture."

Jan 1, 2004

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By Kot Unrug

The selection of tensioned versus non-tensioned roof bolts, for primary coal mine roof support, has been debated for well over 25 years. The wide spread use of fully grouted rebar marked the beginning of the discussion of the relative importance of bolt tension and the resultant immediate roof compression. The focus is on roof conditions encountered in coal mines however the discussion may be extended to hard rock mines as well. The theoretical bases for both systems are presented, with the analysis focused on the bolt's ability to actually fulfill the theoretical assumptions. Of specific concern are assumptions about bolt tension upon installation and the likelihood of maintaining useful bolt tension over time. The usefulness of tension roof bolting is limited by the mechanical interaction of roof bolt assembly and the rock, which may be valid at the time of installation only. Ambient mine atmosphere and fluctuation in moisture content changes the physical condition of rock, which may have a significant impact on the effectiveness and longevity of bolt tension. Changes in the material properties of the surface of the immediate roof can invalidate the assumptions, which were made in the design stage of roof support system. This means that the roof support in the long term excavations may be inadequate requiring costly rehabilitation. The presented arguments are illustrated with the examples of some relevant experimental data. Tension primary roof bolting is recommended where the immediate roof is: ? Stiff with a high modulus of elasticity ? Surface layers are continuous and fairly thin ? Not easily weathered

Jan 1, 2004

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

Despite the wealth of information available on phase equilibria of oxide systems there remainmany gaps and inconsistencies in our knowledge base. From an industry perspective there is anongoing need to adequately describe the phase chemistry of slag systems in order to optimizeprocess performance and improve productivity. Since this chemical behaviour cannot be predictedfrom first principles it follows there is also an ongoing need for accurate experimental data. The advances made in recent years in the capabilities of sophisticated analytical and measurement equipment have made it possible to develop new experimental techniques for the direct determination of phase equilibria in low order and complex multi-component slag systems. In addition the development of powerful computer modelling tools makes it possible to provide more comprehensive descriptions of the phase chemistry, to present the information in a range of perspectives, and to critically analyse the various types of related thermodynamic and structural information available. This review provides an overview of the types of information that can be used to determine phase equilibria in slags systems, analyses the influence of uncertainty and the relative importance of these types of data, and describes the advantages and limitations of the various experimental techniques that can be employed to obtain this information. Examples of recent studies are provided that demonstrate how an integrated approach to the determination of phase equilibria in complex systems, involving the use of targeted experimental studies and systematic thermodynamic model development, can lead to a better utilization of our current research capabilities and resources and more accurate descriptions of these systems. Keywords: slags, phase equilibria, experimental techniques

Jan 1, 2004

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

Delivery of effective plant shutdowns is primary to the business success of mining and processing plant operations. This paper sets out a methodology that starts with understanding the business objectives of the shutdown and promotes rigorous detailed planning, effective communication, appropriate governance and effective participation of plant operations personnel. The result is delivery of business effective outcomes.

Jan 1, 2004

By R. W. Fedors, S. T. Green, F. T. Dodge, D. B. Walter

Spatial and temporal temperature variations in a high-level radioactive waste repository drift can give rise to moisture transport within the drift. Knowledge of this moisture transport may be important to assessing the potential for corrosion of all metallic components in the drift. The model presented here shows one approach to simulating evaporation, transport, and condensation of water in large underground openings using a framework based on computational fluid dynamics. Simulation results that explicitly model water and latent heat transport are presented.

Jan 1, 2004

By J. M. Dempsey, R. A. Litle

Asarco Incorporated’s Omaha, Nebraska refinery site and the City of Omaha’s downtown redevelopment projects are the perfect example of the marriage of the Brownfield and Sustainable Development strategies. Nebraska’s largest voluntary site remediation project created a focus point for redevelopment and has spurred over $1 billion in economic investment within a 1-mile radius of the site. Asarco was faced with options of very expensive and uncertain facility upgrades or a shutdown. Local leaders, Asarco, and regulators worked together to convert a controversial and complex site to a park-like redevelopment area with numerous long-term benefits to the City and the environment.

Jan 1, 2004

By Kenneth Eltschlager

Business says that location is a primary component of being successful. So too is the importance of location in blasting. For blast seismograph data to be useful, the location of the blast and seismograph must be clearly documented. Another location of importance is that of a nearby structure. Establishing the spatial relationships between the blast, seismograph and nearby structures, allows the blaster to correctly interpret the data, evaluate the performance of the blast and gauge the validity of any complaints.

Jan 1, 2004

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By J J. Plumb, P D. Franzmann

A study was conducted to describe the microbiology of the MICCL Monywa chalcocite heap bioleaching operation. Microorganisms were detected in the heap using culture-based techniques and cultureindependent PCR-DGGE analysis of the 16S rRNA gene. The metabolic requirements, temperature and pH optima were determined for selected strains isolated from the heap material. Six strains (BH1-BH6) were enriched and isolated from heap solids and leachate samples. Phylogenetic analysis of the 16S rRNA genes showed that strains BH3 and BH4 were closely related to the acidophilic bacterium Acidithiobacillus caldus and strains BH5 and BH6 were closely related to Leptospirillum ferriphilum. The optimum growth temperature for L. ferriphilum was 41.3¦C and the optimum pH range was 1.1 to 1.5. A new species of Archaea was isolated from the heap samples. Cells of the proposed species, Ferroplasma cyprexacervatum (æcyprusÆ L.n. meaning copper; æexacervoÆ L.v. meaning æto heap upÆ), are non-motile pleomorphic cocci, capable of chemomixotrophic growth with ferrous sulfate and yeast extract. Cells grow anaerobically on ferric iron in the presence of potassium tetrathionate and yeast extract as electron donors. Growth occurs from 14¦C to 63¦C, with an optimum temperature of 55.2¦C. The optimal pH for growth was 1.0 - 1.2. The species was phylogenetically most closely related to Ferroplasma acidiphilum with a 16S rRNA gene sequence similarity of 95 per cent. Molecular analysis of mine samples (16S rRNA PCR-DGGE) detected the above-mentioned cultured strains of microorganisms as well as species of Sulfobacillus and other unknown Proteobacteria. The microbial community of the Myanmar bioleach heaps contained similar levels of diversity to a dump bioleach operation in Chile, but contained greater amounts of biomass than another heap bioleach operation in Australia. The operating parameters of the Myanmar heaps (low pH and moderate temperature) have selected for the growth of moderately thermophilic microorganisms that are more commonly found in extremely low pH acidic mine drainage sites than in heap systems. The novel species of Ferroplasma is thought to be involved in the aerobic and anaerobic cycling of iron within the heap bioleaching environment.

Jan 1, 2004

By Jin-Hwa Song

Rolling temperatures and cross rolling ratios were varied to investigate the effect of crystallographic texture of alpha-phase on the anisotropy of mechanical properties in modified Ti-6A1-4V alloy. Hot rolling method was unidirectional and cross rolling, during which the rolling temperature was in the range of 830°C and 920°C. Cross rolling ratios were varied from 0.3 to 1.0 at 875°C. For unidirectional rolling, as the rolling temperature increased texture changed from the mixed basal and transverse texture to the simple transverse texture. Contrary to other work, it was observed that the maximum intensity of transverse components increased with the increase in rolling temperature. For cross rolling, on the other hand, the transverse texture component was almost suppressed at 830°C, giving rise to a symmetrical basal texture. With increasing cross rolling temperature, the transverse texture components developed again. A simple transverse texture, which showed two maxima appearing circularly 90° apart, was observed at 920°C. It was found that unidirectional rolling could not eliminate the transverse texture, which resulted in the anisotropy of mechanical properties. The anisotropy of mechanical properties obtained from tensile and V-notch Charpy test was closely related to the crystallographic texture and its intensity at each rolling condition. To obtain the isotropy of mechanical properties by cross rolling, it is suggested that cross-rolling ratios should be controlled above 0.5. The variation of rolling temperatures and directions has great influence on the anisotropy of impact value rather than tensile strength.

Jan 1, 2004