Search Documents

By M. Hagfors

Underwater explosions have been used several decades for the determination energy content of explosives. It’s the only test method by which shock and gas heave energy values can be determined separately. The total energy is a sum of these two partial energies. This test method enables us to develop explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The method also enables us to observe the changes and to adjust the energy content of an explosive as a function of increments of one or more energetic component.

Jan 1, 2006

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By Dyno Nobel

Impact of Enhanced Security on Operations Budgeting - What is the “value” I receive for enhanced security? Is there a “return” for the money I spend? Regulatory driven Economic driven

Jan 1, 2006

By Jong-Oh Jo1

Thermodynamics of Ti, N and O in liquid iron was studied in order to establish a data base for the prediction of TiN and TiOx formation in liquid stainless steels containing various alloying elements including Cr, Ni and Si as a function of temperature. The interaction parameters of these elements on Ti and N were determined using the metal-nitride-gas equilibration technique. The TiN stability diagram for a commercial stainless steel grade was constructed from the measured thermodynamic parameters, and its validity was confirmed experimentally. The interaction parameters between Ti and O, and the equilibrium constants for Ti deoxidation reactions for the formation of Ti2O3 and Ti3O5 were also determined by the equilibration of the melts with those oxides identified by the XRD and the EPMA analyses.

Jan 1, 2006

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By C J. Moran

The Gladstone region, as one of the most industrially intense regions in Australia, uses significant quantities of fresh water. Awoonga Dam, situated on the Boyne River, is the only major source of water in the region. The current typical annual usage is 53 GL (Porteous, 2006) and approximately 80 per cent of the water is used by heavy industry (Gladstone Area Water Board, 2004). Until relatively recently, there has been ready and easy access to raw water for industrial use. The recent drought, which resulted in severe water restrictions in 2002 and 2003, emphasised the importance of water for a dominant industrial region like Gladstone. Although now in the process of changing, the typical contractual arrangements in the past have provided little financial incentive for efficient water use. From research undertaken on potential water reuse opportunities, several key questions have emerged related to water management in an industrial region such as Gladstone. This paper highlights these key questions, presents findings from recent regional strategies and assesses the potential for water reuse. Even though there is no clear-cut financial incentive for reusing water, there could be stronger regional and risk mitigation drivers for doing so. Initiatives to incorporate adaptive capacity through collaborative industrial synergies would allow for robustness and resilience in water security, leading to long-term sustainable water management across the Gladstone region.

Jan 1, 2006

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By C. Braun, C. Kennedy, P. Katsabanis

A series of small scale tests, simulating multi-hole blasts have been performed to establish the effect of delays on blast fragmentation. The blasts were performed in high quality granodiorite blocks, which were cut from stone prepared by dimensional stone quarry operations. The pattern used was equilateral triangular, with a distance of 10.2cm between boreholes, which had a diameter of 11mm, were loaded with detonating cord and the coupling medium was water. The delays used were achieved using different lengths of detonating cord for the cases of delays between 0 and 100 microseconds between holes and a sequential blasting machine firing seismic detonators for larger delays up to 4ms. All fragments were collected and screened. The experiments showed that the coarsest fragmentation was achieved with simultaneous initiation of all charges. Fragmentation became finer with delay time between holes up to 1ms between holes. The results show that in moderate to competent rock, similar to the granodiorite of the experiments, fragmentation optimization requires delays of few milliseconds per meter of burden. In view of the findings, which agree with previous published work, the current trend of selecting fast firing times for fragmentation optimization is questioned.

Jan 1, 2006

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

By Peter Moser, G. Reihholf

Holcim, one of the world's leading suppliers of cement, aggregates and concrete, has set up a few years ago a working group “Quarry” in order to optimize the performance of its central European quarry operations in terms of work safety, environmental standards and economic performance. One of the activities of this working group "Quarry" addresses the subject of blast fragmentation in the quarries. A benchmark study of the blast work in all quarries has shown substantial differences for the various operations in terms of drill& blast costs. Especially big differences were found with respect to the drilling patterns as a function of the borehole diameters and with respect to the utilization of the borehole volume for charging the explosives.

Jan 1, 2006

By R. Hardy

LaModel is a boundary-element program capable of calculating the displacements and stresses in thin bedded deposits such as coal, salt, or potash. Throughout its history, it has continually been upgraded in order to expand analysis detail and stay current with the latest advances in computer technology. The most recent enhancements include: an increased grid size capability, a significant increase in the speed of the automatic grid generation using an AutoCAD visual interface, implementation of subsidence-based horizontal strain calculations for multiple-seam situations, and pillar safety factor calculations. To demonstrate these new features, a multiple-seam case study of a longwall panel undermining an active set of main entries is presented.

Jan 1, 2006

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006