Search Documents

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By I. Beukes, H. Kotze, B. Krause, R. P. Hattingh

Hillendale Mine is operated by Exxaro KZN Sands, and is situated on the north coast of KwaZulu-Natal in South Africa near the towns of Empangeni and Richards Bay, some 200 km north of Durban. During the mining operation the heavy minerals rutile, ilmenite, zircon and leucoxene are extracted for further beneficiation at a processing complex near the town of Empangeni. The deposit contains approximately 25% slimes (defined as the sub-45 micron fraction), and is mined using hydraulic monitoring. Run of mine is gravity fed down launders to pump stations, which deliver the material to a primary wet plant. Slimes is separated from the run of mine prior to the heavy minerals being separated from the sand. Sand tails containing approximately 2-5% slimes is pumped to the mining void. The slimes is thickened to a density of approximately 1.2, and most of the resultant material is pumped to a sub-aerial deposition site (residue dam). The area is characterized by an annual rainfall of approximately 1300 mm, which is relatively high by South African standards. From an agricultural perspective the soils are deep and well weathered. Dryland agriculture has been practised on an extensive scale in the area for the past 70 years. Sugar cane in particular is cultivated on and around the mine area. In terms of environmental approvals, the post-mining land use and objectives are defined as economically viable and sustainable sugar cane cultivation in the mined areas. During mining the soil profile is destroyed. In this paper the establishment of a reconstituted soil profile is discussed, with specific reference to the methodology that is being followed to achieve the homogeneous blending of sand and slimes. Defining the rehabilitation strategy and soil specification Strategically Exxaro KZN Sands divided rehabilitation into four aspects, comprising physical rehabilitation (restoration of soil structure), vegetative rehabilitation (restoration of vegetative cover), ecological rehabilitation (restoration of sustainable ecological communities), and sustainability (sustainable man/environment interface) (Hattingh and Viljoen, 2006). It is believed that the key to successful rehabilitation lies in achieving a substrate (soil) suitable for the establishment of the target vegetation. During the development of the rehabilitation strategy the key factor in the establishment of a suitable soil profile was shown to be the soil water retention of this material. Since dryland agriculture is practised, this aspect becomes critically important in ensuring that the post-mining land use is sustainable (Hattingh et al., in prep.). From a financial perspective, a closure certificate being issued implies that the state takes over financial liability for the rehabilitated land. This has significant implications for the state-the default position will be that all possible latent and residual impacts must be identified and known prior to a closure certificate being issued. From the mine's perspective this precautionary approach by the state implies that post-operational costs cannot be quantified exactly, and our approach is therefore to mitigate the risk of a long post-closure care and maintenance phase by means of addressing all potential latent defects during the operational rehabilitation phase. The financial viability of the soil reconstitution process itself is therefore not measured against other rehabilitation methods, but against the risk of not achieving closure. During a series of technical workshops comprising experts in the various disciplines in the rehabilitation of the soil profile were identified. These aspects include the re-establishment of a functional soil profile, soil physical characteristics, soil chemistry, soil biota, salinization potential, erodibility and soil weathering. The natural soils in the Hillendale area have been classified in terms of the South African soil classification system (MacVicar and co-workers, 1991) and consist of Hutton (orthic topsoils on red apedal subsoils) and Clovelly (orthic top soils on yellow apedal subsoils) soil forms. The topsoils consistently comprise medium to fine grained sand overlying heavier textured sandy clay loam to clayey subsoils. The topsoil structure consists of a single grain structure, whereas subsoils are apedal. These soils are typically deeply weathered and do not show secondary structures. During the mining process a layer of topsoil (300 mm) is stripped off, and the balance of the material down to the footwall is processed. Sand with 2-5% slimes (defined as the sub-45 micron fraction) is returned as backfill in order to re-establish the dune to approximate the previous landform. From an agricultural perspective this material is not suitable for the dryland cultivation of sugar cane. A capping of more suitable material therefore has to be provided. The most significant difference between the premining soil form and the backfill material is the percentage slimes, consequently a mixture of the sand and slimes is required as a capping over the backfilled sand. The required thickness of the cap is a function of specifically plant growth requirements, erodibility, weathering and runoff (Hattingh, et al.; in prep.). The percentage slimes required in the cap is a function of mainly soil water requirements (Hattingh and Viljoen, 2006). The conservative indications to date show that the reconstituted soil profile should consist of a homogeneously blended mixture of 70%-80% sand and 30%-20% slimes up to a maximum of 2 metres thick. This will be sufficient to ensure growth during dry periods.

Jan 1, 2007

By A J. Broome

Since 2003, there has been an unprecedented growth in the demand for engineering, technical and project services in the mineral industries. This demand for services became evident in Australia earlier than many other markets and has since spread globally. This growth has created significant issues for the strategic direction and planning by the service provider. Such strategic questions include:- how fast to grow, how to recruit, train and integrate new staff, what market sectors to service, the selection of targeted customer sectors and managing strategic growth with short term demands and commercial reality. These factors are discussed using in depth experiences and examples that illustrate these strategic approaches. The relevance of this new industry environment to New Zealand services will be highly discussed.

Jan 1, 2007

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By A. Cáceres, L. Navarro, N. Altmann, R. Betinol

Copper concentrate is produced in Chile in the high Andes and transported to the coast for shipping through long distance pipelines. The pipeline and fittings installed have to withstand the high abrasion and corrosion environment of the copper concentrate. To protect the inside tube wall against corrosion, high density polyethylene (HDPE) liner is used. While HDPE liners can protect the steel wall against corrosion, it has also been assumed that the low surface roughness of the HDPE liner also inhibited incrustation caused by calcium carbonate and sulphate deposition. Recent events have indicated otherwise in a couple of concentrate pipelines for which BRASS has provided consultant service. This paper delivers a case study which includes (i) formation of incrustation and adhesion to HDPE liner, (ii) the detection of the incrustation through hydraulic analysis, (iii) the mechanism of removal of incrustation, and (iv) the catastrophic effects of their presence in an emergency situation.

Jan 1, 2007

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By A. Chamaret

Minerals extraction is related to complex sustainable development issues that are subject to international and local controversies. Debates must be based on objective and comparative elements. Defining strong indicators for assessing impacts and performances of mining sites thus appears necessary to inform and support the decision-making process for stakeholders. Recently, many indicator sets have been developed on an international level based on top-down approaches, but they commonly lack legitimacy for stakeholders and adequacy to specific site issues. They thus need to be complemented by the consultation of local actors concerned by such mining activity, in order to define indicators that are closer to the needs and contexts of the specific sites. The question raised by this kind of top-down/bottom-up approach is how to organize and reveal the plurality of values and concerns associated with mining. Based on the principle of representative diversity, the approach undertaken at the Arlit uranium mines in Niger aimed at defining indicators that are understood and accepted by all actors. The aim was to measure the impacts and performances of mining sites in the four sustainable development dimensions, and at local, regional and national scales.

Jan 1, 2007

By Z. Jun, L. Kerning

Jinlong copper smelter and refinery, originally designed for 100,000tpa primary copper and started up in 1997, has been expanding its capacity on the basis of operational optimization and by modifying its facilities. Currently it is producing 210,000tpa primary copper, and the new phase of expansion project with a target capacity of 350,000tpa primary copper is ongoing. This paper reviews problems and improvements made with operation and equipment in the past years. Recent plant operation is briefly described. The expansion projects completed are summarized and the ongoing expansion project is present.

Jan 1, 2007

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By Robert Hopler

In the annual report under the Explosives Act for 1905, H.M.inspectors state that over 90 percent of the accidents causing death or personal injury occurred in the use of explosives and under miscellaneous conditions to which the controlling provisions of the Act do not apply, and that such accidents caused 43 out of the 50 deaths, and 312 out of 348 cases of injury. The number of accidents grouped under the heading of “Use and Miscellaneous” is less than that for 1904 - viz., 281 against 301. By these accidents 43 persons were killed and 312 injured, as compared with 39 killed and 343 injured in 1904

Jan 1, 2007