Search Documents

By Shunhong Huang

To improve understanding the effect of heavy metal chromium on soil biota, laboratory incubation experiment was carried out in the soils contaminated artificially with five concentrations of chromate (50, 250, 500, 1000 and 2000 mg kg_1 soil) over time (35 days). The population and diversity of bacteria, fungi and actinomycetes in soils were measured as indicators of soil microbial processes in the disturbances mentioned above. Incubation experiment results elucidated that the population and diversity of microorganisms decreased with increasing Cr (VI) concentration. Furthermore, various microorganisms showed different sensitivity to total Cr contamination. The sensitivity of microbial population to chromium contamination was in the order: actinomycetes >bacteria>fungi. The resulted implied that the microorganism can be used as an indicator of chromium contamination.

Jan 1, 2008

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Haldun Kurama, Cenk Karakurt, Ilker Bekir Topçu

"The usage of binders or pozzolanic materials in the production of concrete is not new. However, in recent years, the use of the pozzolanic siliceous material such as natural zeolite and coal combustion ash (CBA) has received re-attention due to the generated considerable interest in the economical use of both naturally occurring raw materials, recycling of the waste material and saved energy. In this study, the potential and utilization opportunities of natural zeolites and bottom ash (BA) in concrete applications were reviewed. Case studies, conducted to determine the possible usage of the natural zeolite and BA in concrete production, i.e. light weight concrete (LWC) were also presented. The physical and mechanical properties of cured concretes were examined to find out the competitive material usage on the final product properties. Autoclaved aerated concrete (AAC) with 1.1 nm tobermorite (5CaO 6SiO2 5H2O) as binder is a lightweight construction material that mainly uses in place of concrete to manufacture various building materials, including blocks, panels, slabs and the like. The material is a mixture of sand, lime, cement, gypsum, water and an expanding agent, which causes the raw material to rise like bread dough, with countless small air pores. AAC can be molded and cut into precisely dimensioned units and cured in an autoclave, which steam cures the concrete under pressure. During this process, the ingredients combine to form the calcium silicate hydrate gels that establish the special properties of the finished product. The process produces a material that is only one-fourth to one-third the weight of a conventional concrete block (bulk density of 400-800 kg /m3) of the same size. Regular AAC offers considerable advantages over other construction materials such as high thermal and sound insulation, excellent fire resistance, high resource and energy efficiency, low environmental impact, and finally outstanding structural performance (especially for earthquake zones) [1]. Its lightweight also makes it easy to use during construction, and its aerated structure gives it better thermal insulation and sound absorption properties than conventional concrete."

Jan 1, 2008

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By Adam K. Smith

Occupational hearing loss is a permanent illness with no recovery currently possible. For underground coal mine workers, Noise Induced Hearing Loss (NIHL) continues to be a serious health issue. One of the principal and fundamental machines used in underground mining operations is also one of the loudest. Noise generated on the continuous mining machine is the result of 3 operational components: the cutting system, the dust collection system, and the onboard conveying system. During underground acoustic evaluations, the conveyor system noise was observed to be dominant. In order to more closely examine sound generated by the continuous mining machine, sound power levels were measured in a reverberation chamber at the Pittsburgh Research Laboratory (PRL). Different chain types and configurations were installed on the conveyor system, and the resulting sound power level ranged from 118 dB(A) to 108 dB(A). Noise generated by the dust collection system was also examined and found to be 107 dB(A).

Jan 1, 2008

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By H W. Wu, T Harvey

An overview is given of two new developments in mine atmospheric monitoring. A new personal dust monitor (PDM) that gives real-time respirable dust readings is discussed. The unit is mounted within the minerÆs cap lamp battery and internally measures the true particle mass of dust collected on its filter. Samples are available for later mineralogical analysis and results do not exhibit the same sensitivity to water spray as optically-based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment and reports dust loading data on a continuous basis. The monitor has been evaluated under an Australian Coal Association Research Program (ACARP) grant and is being adopted for statutory mine respirable dust determinations in the United States (US). The monitor has particular application for determining location of high dust sources. It can evaluate the efficiency of engineering means of suppression and other approaches to reducing dust levels. It has been recognised that the PDMÆs unique measurement approach has application to allow real-time atmospheric diesel particulate matter (DPM) monitoring. The industry has no real-time atmospheric DPM monitor at present. Recent surveys in New South Wales and Queensland show significant numbers of miners continue to face full shift DPM exposures in excess of internationally accepted levels. Real-time DPM monitoring will allow the industry to pinpoint high exposure zones where a number of trucks and other vehicles work in areas of poor ventilation. Knowledge of high DPM concentration zones allows efficient modification of work practices to reduce underground minersÆ exposure. Approaches to uses of the DPM form of the monitor and the design of tag boards are discussed. Some outcomes from mine tests with both these new instruments are given.

Jan 1, 2008

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By R Pozo, F Reyes

Codelco Chile is currently developing the El Teniente û New Mine Level Project (NMLP) in order to increase ore production by seeking to mine the ore deposit located under the current operational orebody. Reserves of 2000 million tonnes (Mt) have been quantified, which will be extracted as from the year 2017 by using the panel caving and progressive sinking method. Codelco and SKM Minmetal (SKM) jointly developed the project prefeasibility stage (PFS), closing these studies in March 2008. The first part of the project approach is to replace mine production currently feeding the Colon concentrator facilities with 137 000 tonnes per day (t/d), focusing attention on a production increase from the year 2026 up to 180 000 t/d. Project efforts have also been centred on maximising the contribution of new technologies for both construction and operational phases of the New Mine Level, together with selecting the best mine infrastructure to keep El Teniente operations going on for the next 50 years. Implicit in this is the inherent improvement of a variety of current Mina El Teniente process and management practices. The plan is to reduce actual mine operational risks and take advantage of new opportunities afforded by the project, which is in effect a greenfield project with respect to the implementation of fundamental changes in the labour and business environment. In addition, issues related to human resources, maintenance and management, materials handling, establishing centralised operations and accesses, automation and remote operations control and power efficiency could also be addressed. The project, beyond the New Mine Level exploitation, considers the mineÆs future potential, with a second deeper exploration in prospect named Deep Level. Finally, the project identifies features that would add value to the mine operations, in an initiative named æSpace for Future TechnologiesÆ. This will allow the eventual implementation of new electrical equipment and the application of mechanised technologies and other process improvements for the mine development.

Jan 1, 2008

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Fabio J. Esper, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Cassio P. Carvalho, Giorgio Grotti, Reginaldo B. Santos

"Rejected sands from smelting metallurgical process because contain lead and others heavy metals are a problem to dispose as waste in all the countries. A procedure that is being proposed for it is to incorporate it on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The main goal of this paper is to present the results obtained with mixtures of sands from smelting metallurgical process with common clay from Jundiaí, São Paulo, Brazil. Preliminary incorporation tests (1,0% in weight) were made with hand formed spherical samples. With the higher compression strength of the spheres after drying and firing (950ºC) experiments on bricks production were made for quality technological test. Seven hundred hallow blocks containing 1,0% waste were produced and presented ceramic properties similar to those without sand incorporation. Introduction In last the fifteen years the LMPSol - Raw Materials & Non-metallic Solids Laboratory – Metallurgic Eng. & Materials Depto. – Polytechnic School - University of São Paulo comes studying the possibilities of incorporate industrials waste materials to the production of bricks and other products of construction aiming at to remove pollution products of the environments and to user the properties of the same ones in the structural ceramics products. Examples are the study of the influence of rejected steel furnace dusts in structural ceramic [1], another example is the main subject of the present paper: use of rejected sand from smelting metallurgical process in the production of bricks an other products of structural ceramics. Antecedents More or less one year ago, specialist and members from the direction board of METALÚRGICA GROFE LTD. Company contacted researchers and professors of the LMPSol – PMT – EPUSP seeking for a solution to their concern with the disposal of rejected sand from smelting metallurgical process."

Jan 1, 2008

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

Longwall mining is a commonly used method of coal extraction that involves the complete removal of large, rectangular panels of coal. Longwall mining causes the immediate seam roof to break and fall into the void created by mining. The convergence of the surrounding strata towards the mining void causes subsidence on the surface. The subsidence magnitude is related not only to the mining depth, the topography, the geological features and the overburden materials, but also to the sequence of the strata overlying a coal seam. In additional to the vertical subsidence which is evident at the surface, there are also horizontal movements inwards toward the centre of the void, which cause the surface to tilt, bend, stretch and com-press. This paper presents a parametric investigation of the influence of the overburden stratigraphy to surface deformations due to longwall mining using 2D finite element models. Models simulate rock movement by applying equivalent edge load to the open roof.

Jan 1, 2008

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008