Search Documents

By W. H. Bassett

THE modern smelting and refining of copper is distinctly an American development. The present demand for sound and perfect castings for rolling is due to the development of American industry. Prac-tically every article made from sheet metal or, for that matter, from any form of metal is made by mass produc-tion methods. Faulty material disturbs the orderly sequence of operations and in addition requires expen-sive inspection and unbearable rejection of finished product. This demand, therefore, is positive and will have to be met. Some mines produce ore that can be smelted and re-fined without the electrolytic process into satisfactory copper for the wrought metal industry, and some of these ores carry small amounts of impurities that are of use in hardening and toughening the copper. Most of the copper ore mined contains impurities that must be removed and, fortunately, precious metals which are separated at the same time make this re-moval profitable. The modern electrolytic refineries have their methods so well under control that the product meets all re-quirements without question if properly fire refined and cast. The "if" in this case is important, because there is evidence of carelessness or want of control at times in the material from some of the producers. It is nec-essary that the melted cathodes should be saturated with oxide to dispose of sulfur and that the copper should then be poled to the proper pitch or set. Sometimes statements leak out to the effect that it is unnecessary to oxidize completely the molten cathodes and a little less rabbling saves poles, which are expensive. The re-sult is that the rolling mill gets porous castings and produces seamy or slivered sheets or strips. The condition of the molds, their temperature, and the temperature of the metal are all important to good copper cakes, wedges, or wire bars. Cracked, and burned molds leave rough places and porous spots. Molds which are out of shape, or cracked, make shrink-age cracks which gap open when the castings are hot-rolled. Dampness means porosity. Drops of oil mean porous or honey-combed areas. Poor or irregular dress-ing means mold wash in the castings. Cold copper or slow pouring means cold sets.

Jan 4, 1928

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Jan 1, 1949

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal&apos;s resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,&apos; Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O&apos;Neill&apos;o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,&apos; has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker&apos;s commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.&apos; Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By E. P. Polushkin, Henry L. Shuldener

This paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. Pipes Examined The pipes were made by different manufacturers and their sizes range from 3/4 in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often IOO to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is Ioo° to 160°F. Water Supples The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table 1 are characterized by relatively low hardness, 10, alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1945

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45&apos; to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;&apos; Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

Experimental work on the properties of high-purity alloys of the copper-man-ganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. Previous Work Heuslerl conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilib- rium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alpha-beta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350&apos; to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur6 have also noted this precipitate. Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By Svetlana Krashenina, Nebojsa Petrovic, Oscar Lopez

"As easily mined gold deposits are becoming increasingly rare, gold producers are turning to the processing of ores with polymetallic and copper mineralization. These base metals can create metallurgical and waste handling/disposal challenges, which can render the project uneconomic. Base metals such as copper compete for the cyanide reagent used to extract gold, necessitating the need to increase cyanide volumes and consequently, cyanide consumption costs. Copper will also stabilize in tailings water as weak acid dissociable cyanide, a form that is both difficult and costly to destruct. SART (sulphidization-acidification-recycling-thickening) process technology can be applied to remove base metal interferences in gold projects. SART breaks the copper-cyanide complex and precipitates the copper as a saleable copper sulphide concentrate. With the copper removed, the cyanide can be regenerated as free cyanide for recycle to the gold recovery process. This improves cyanide utilization efficiency and mitigates copper presence in tailings. Additionally, copper recovery generates an incremental revenue source to further improve project economics. Engineering Dobersek GmbH together with BioteQ developed a SART and AVR testing program to recover cyanide and maximize operational efficiencies at a gold processing plant in Kazakhstan with high cyanide consumption in the leach circuit. Results from on-site testing demonstrated that up to 99.98% of copper can be removed and precipitated as copper sulphide and 60-90% of cyanide can be recovered from the AVR and recycled for leaching, reducing total overall cyanide use. This paper provides an overview of the testing methodology and results together with a discussion on the potential of SART to improve gold production operations to deliver both environmental and economic benefits."

Jan 1, 2014

By M. Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molybdenum, lead, zinc, and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high, the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper prices; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1984

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By John G. Hall

Everyone forms his own mental picture when the subject of copper is mentioned. To an architect, copper is a warm, enduring metal with a quiet beauty; to the historian, man&apos;s first metal; to the product engineer, the best electrical and thermal conductor of all commercial metals; to the investor, a volatile stock; to the speculator, the daily price quotation; to those in the mining industry, the challenge of producing copper for rising needs in the face of rising costs and lower grades of ore. At this meeting, we will look upon copper as a key raw material in industry, in national defense, in technology, in world trade, and as a principal commodity in the economies of several developing countries. As miners, and most of us here are miners, we are prone to view our role as suppliers of copper. We locate, mine, smelt and refine the metal. In the complexities of today&apos;s world, however, following a period of the longest domestic copper strike in history which caused critical world-wide shortages and widely fluctuating prices; it becomes necessary for all of us to concern ourselves with the whole spectrum of copper affairs -"from mine to consumer " But first we need to look at the miner&apos;s side of the picture -- capacity and production. We will examine these functions in terms of the whole world -- not simply the free world. Nature did not endow all regions of the earth equally, and copper in world trade has a way of ignoring political boundaries. Science and technology, as well, know no national boundaries. It is said that the "Engineering & Mining Journal" has as many readers in the Communist World as in the Free World. Nor is this a one-way street. We presently have available to us in the. U.S., cover-to-cover translations of many Communist World mining and metallurgical journals.

Jan 1, 1968

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By P. Bevilacqua

In this paper the possibility to complete the copper recovery and to enrich in PVC a mixture of plastic granules obtained by grinding electrical cables are investigated. The recovery of a large part of the copper still present among the plastic granules was possible by means of a mechanical screening, the finer polymeric fraction was collected, at the same time. In order to complete the copper polymer separation the following techniques were employed. Counter current separation in water, static dense medium separation with zinc chloride solution and copper extraction with nitric acid and subsequent electrolytic deposition. A Tri-Flo® dynamic dense medium separator was employed in order to separate the lighter polymeric fraction, from the heavier polymeric fraction, mainly PVC. Water or a salt-water solution was employed to feed the separator device.

Jan 1, 2014

By G. L. Hundley, D. N. Nilsen

The U.S. Department of Energy investigated the use of liquid-emulsion membranes (LEM) for the selective removal and recovery of metals such as copper and zinc from mine waste waters. This investigation included field tests of a mobile, pilot plant-scale, continuous-flow LEM system. The system was tested at copper mines with solutions containing from 100 to 1,400 ppm Cu, and at a zinc mine with a solution containing 115 ppm Zn. Typical results from the copper tests were >90% copper recovery, and zinc extraction from waste water also was typically>90%. Although all of these waste waters contained high impurity levels, pure products were produced. On several of these field tests, integrated systems were tested that resulted in recovery of metal by-products, selectiv~ precipitation of iron, and polishing to reach discharge targets for essentially all of the contained metals. In addition, some results are included from laboratory-scale tests.

Jan 1, 2000