Search Documents

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By Joseph M. Morrison

This paper offers a comprehensive solution to the problem of dust emissions at belt conveyor transfer points. It discusses details of enclosure design and presents a straightforward procedure for calculating required dust control exhaust volumes. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds, enclosure openings, material flow rates, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these quantities are handled by means of a "fill-in-the-blanks" type of calculation form which permits quick, reliable solutions by relative "non- experts".

Jan 1, 1970

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By Mingju Liu

The coal and gas outburst accident on May 20, 2007 at Sihe Coal Mine is unique in that there was no or very little soft coal in the coal seam and that the coal strength was very high. The outburst also showed that there was a very high gas content of 20-30 m3/t in the coal seam nearby the outburst site. Based on the field test and observations, together with laboratory experiments, detailed analysis was conducted on the controlling factors of coal and gas outburst potential at Sihe Coal Mine. Stress data available from Sihe Coal Mine, northern China, and other parts of the world, were also taken into account to facilitate the analysis. The results shows that the stress level was not abnormal compared to other coal fields in China prone to outbursts, and that gas contained in the coal seam was the main factor that triggered the outburst. All these factors were essentially controlled by the tectonic evolution features in Qinshui Coal Basin, to the Southeast of which Sihe coal field is located. Based on the analysis, assessment of coal seam outburst potential was carried out by measurements of coal seam gas contents, observation, and detection of soft coal layers in the coal seam. The results show that outbursts are limited to only a small part of the whole coal seam and that the eastern part of coal field is not prone to outbursts.

Jan 1, 2009

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By Richard C. Enochs

In order to clearly understand our process control system it is necessary to briefly discuss the various process control systems that were considered and why we chose our particular configuration. We considered Analog Systems, Computer Supervisory Systems, Computer Setpoint Systems, Direct Digital Systems and Direct Digital with Backup Systems. Our concept of these systems is illustrated in Figure 1 through Figure 5. We chose Direct Digital Control with Manual Backup because it had the greatest flexibility, ease of implementation and cost no more than a pure Analog Control System for one control concept. There would be no increase for a Direct Digital Control with Manual Backup System if the control concept were changed, while there could be considerable additional cost with an Analog System, if the control concept were changed.

Jan 1, 1975

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By Pengfu Tan

Xstrata Copper at Mount Isa in Australia has operated one copper Isasmelt furnace and four P-S converters. The phenomena of foaming occur in above 10% of converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow. The model predicts the chemistry and viscosity of copper skims during copper blow. The effects of oxygen potential, charge of dirty materials, slag carry-over, under-blowing, over-blowing, and temperature on the foaming and viscosity of copper skims have been discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2006

By Mohammad A. Pasha, John T. Atkins

Utah International&apos;s Shirley Basin Mine is located in the Southeastern High Plains of Wyoming at an elevation of 7100 ft. The Shirley Basin area is a gently rolling semi-arid land. The uranium ore zone occurs at depths ranging from 270-350 ft below the surface. Overburden consists of poorly consolidated sandstones, siltstones and clays. Underground mining was begun in 1960. Conditions were made difficult by high rates of water inflow and ground support problems. Development of a solution mining or in-situ leaching technique allowed underground operation to be abandoned in 1964. Solution mining provided limited production from 1963 to July 1970. In January, 1969, large scale development of open-pit mining was begun. A 1200 tpd mill went on-stream in March, 1971.

Jan 6, 1973

By John T. Atkins

Utah International&apos;s Shirley Basin Mine is located in the Southeastern High Plains of Wyoming at an elevation of about 7,100 feet. The Shirley Basin area is a gently rolling semi-arid land. The uranium ore zone occurs at depths ranging from 270 to 350 feet below the surface. Overburden consists of poorly consolidated sandstones, siltstones, and clays. Underground mining was begun in 1960. Conditions were made difficult by high rates of water inflow and ground support problems. The development of a solution mining I or in-situ leaching technique allowed underground operation to be abandoned in 1964. Solution mining provided limited production from 1963 to July 1970. In January, 1969, large scale development of open-pit mining was begun. A 1,200 ton per day mill went "on stream" in March, 1971.

Jan 1, 1973

By Kaushik Dey

Bord and pillar is the most predominant method of wining of coal in Indian underground coal mines. Development heading in coal mines often encounters roof stability problem and results in roof overbreak. Research on this reveals that the blast-induced ground vibration may have significant contribution in roof overbreak, especially, when solid blasting is carried out in the bord and pillar method. Solid blasting, in general, is associated with higher charge confinement due to lack of free face and generates higher ground vibration, which in turn results in excess overbreak.

Jan 1, 2008

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002