Search Documents

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By Sergio Quiñones

El presente trabajo señala el control metalúrgico en la planta concentradora de Toquepala a través de la mineragrafía. La mineralización del cobre se realiza en dos grupos: el diseminado (36%) y relleno de fracturas (64%). La dacita porfirítica presenta la mayor intensidad de diseminación fina. En este sentido, el estudio microscópico cuantitativo actual ha contribuido a conocer mejor la caracterización morfológica de nuestro mineral en las diferentes etapas de la concentración y va desde la alimentación hasta la obtención de concentrados y relaves.

Sep 13, 2001

By E. Jannoulakis

This paper introduces a practical methodology for analyzing vi¬bration records in view of improv¬ing blast designs and preempting anomalous vibrations. This technique, which is based on empirical data, uses a blasting-efficiency determinator (BED) as an indicator of vibration-energy transmission. The method was tested using data from a blasting event at an open-cast coal mine in the province of New Brunswick, Canada. The results derived from the BED values showed that geology and delay timing were probably the principal factors that induced high-intensity vibration propagation.

Jan 1, 2000

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By B G. Lottermoser

Phosphate induced stabilisation has been used to create passive iron phosphate coatings on pyrite and pyrrhotite. The formation of solid phosphate coatings on sulfide grains thereby inhibits sulfide oxidation. The aims of the study were to determine whether phosphate induced stabilisation could control sulfide oxidation and metal mobility in partly oxidised, polymineralic, sulfidic mine wastes. Waste materials were obtained from the acid mine drainage generating, abandoned Montalbion silver mine site, far north Queensland, Australia. The waste consists of quartz, kaolinite/illite, sulfide minerals (galena, chalcopyrite, tetrahedrite, sphalerite, pyrite, arsenopyrite), and pre- and post-mining oxidation products (hydrated Fe, Cu, Pb and alkali mineral salts). SEM observations of waste material treated with potassium orthophosphate showed that metal, metal-alkali and alkali phosphate coatings developed on all sulfides (with the exception of tetrahedrite). The abundance of phosphate phases was dependant on the availability of cations in solution for complexation with the phosphate anion. In turn, the release of cations was dependent on sulfide oxidation or the dissolution of efflorescent mineral salts. Experiments aiming to dissolve these phosphate coatings û using a strongly oxidising solution û showed that the phosphate coatings remained stable, preventing acid generation and metal release. The results of this study demonstrate that liquid phosphate stabilisers can suppress sulfide oxidation and immobilise metals in partly oxidised, polymineralic mine wastes.

Jan 1, 2003

Reduce or prevent acid mine drainage from coal refuse piles and surface mines by inhibiting the growth of acid-causing bacteria. Approach A dilute surfactant or deter? gent solution is applied directly to coal refuse piles or overburden using a hydro-seeder or road watering truck. The surfactant treatment can be used either as a preventive measure to avoid a potential acid drainage problem or to reduce water treatment costs by controlling acid drainage at its source. How It Works Acid drainage is prevented or reduced by inhibiting the growth of Thiobacillus ferrooxidans, a type of bacteria which obtains most of the energy it needs to survive by oxidizing ferrous iron in water. The oxidized iron in turn attacks pyrite, which forms an acid and additional ferrous iron for the bacteria to oxidize. T. ferrooxidans is protected by an outer membrane which enables it to survive in its acid environment. Anionic surfactants, or surfactants containing negatively charged ions, can be used to destroy this membrane, thus killing the bacteria and slowing down the oxidation of acid-forming pyrite. Of the anionic surfactants tested to date, sodium lauryl sulfate (SLS) appears to be the most effective as a bactericide. Alpha olefin sulfonate and alkyl benzene sulfonate are acceptable alternatives. These surfactants are major components of common household products, such as laundry detergent, shampoo and toothpaste. They are, therefore, readily available, inexpensive, biodegradable and present no environmental problems at low concentrations.

Jan 1, 1983

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By Shazad Hosein, Rob Farnfield, Bill Birch, Liam Bermingham

The propagation of a shock wave through air as a result of quarry blasting consists only of one type of wave, the compression wave. This is in marked contrast to seismic waves where a number of different types of wave are generated by the one blasting event. Even so the interaction of the burn time of a single hole and the resulting air overpressure is still too complicated to be able to be accurately modelled from first principles. It is considered that the best way forward is to monitor an individual single hole to obtain a signature wave form that has resulted from this complex interaction. Once this wave form is known, the variation in geometry of a mutli-hole blast and the timings of the successive detonations can be modelled to give a sufficient degree of accuracy to recreate the likely magnitude, duration and wave form of a multi-hole quarry type blast. This can then be directly compared with actual air overpressure wave forms from quarry blast to verify the model.

Jan 1, 2012

This paper describes techniques that have been used at RixÆs Creek Colliery to control blast vibration from throwblasts that face a residential area 4 km in front of the face. The paper describes blast design, face control including laser profiling, selective loading of blastholes after borehole camera surveys, and techniques used to assess the effect of burden variation, the cumulative effect of drilling and delay sequence, and the effects of meteorology.

Jan 1, 2001

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By John M. Hird

Texas Gulf Sulphur Company's Lee Creek Mine has opened a major phosphate mining district in the Central Coastal Plains of North Carolina (Fig. 1). The ore deposit as it is now known was roughly outlined in 1961 by a Texas Gulf geologist using wire line exploration methods. Slightly uraniferous phosphate materials were detected by a slim-hole gamma ray probe run in numerous farmers' water wells penetrating the formations. A follow-up-core drilling pro- gram determined the economic ore limits to lie in the south central section of Beaufort County beneath 70 feet to 120 feet of unconsolidated sediments. The 50,000 acre deposit is known to contain over two billion tons of phosphate ore amenable to strip mining methods. A part of the deposit underlies several thousand acres of the Pamlico River estuary. The 90 million dollar capital investment plant built by Texas Gulf during 1965-66 included a strip mining operation using a 72-yard walking dragline, a three million product ton per year flotation concentrator, four fluid bed calciners, a sulphuric acid plant (acid for captive use), a phosphoric acid plant, and three solid fertilizer material plants. Shipment to domestic markets is by rail and truck and to over- seas markets by barge to a transshipment terminal at Morehead City, North Carolina. Early mining investigations were conclusive first that the phosphate ore could economically be recovered only by dry strip mining methods, and second that artesian ground waters in the formation (Castle Hayne limestone) underlying the ore would have to be controlled. This report will relate the application of ground water hydrology in depressurizing the Castle Hayne aquifer to facilitate dry strip mining at depths 130 feet below sea level at the Lee Creek Mine.

Jan 1, 1970

By John M. Hird

Control of artesian ground water has played an important role in the development of Texas Gulf Sulphur's phosphate mining venture in eastern North Carolina. To facilitate dry mining methods, 60 million gpd of fresh water is pumped through wells from a limestone aquifer underlying the uniform flat-lying ore section. Hydrologic information revealed from pumping tests has been used in successfully developing a depressurizing system. Computer assistance is used to plan well patterns. High volume pumping has lowered water levels in water wells over a large area in the Coastal Plain without detrimental effects on water quality in the aquifer. Cooperative effort between mining firms will be required to control the ground water as new mines are developed in the district. An intricate observation -well system is monitored regularly over the wide area of pumping effect to ensure that gradient reversals have not caused salt water encroachment.

Jan 1, 1972

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By Grace B, Cunningham D

The poor quality of bore waters available to the Australian mineral processing industry creates a climate for crystallization of calcium based scales. If ignored, calcite and/or gypsum buildup can cause loss of production and costly unscheduled maintenance. This paper discusses the factors which contribute to scale forma- tion, methods used to monitor buildup and preventative measures (mechanical and chemical) that can be used. A case history il- lustrates the value of using chemical antiscalants.

Jan 1, 1991

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By Raja V. Ramani

Worldwide, promulgation and enforcement of health and safety laws and regulations have been the primary means of ensuring minimum and uniform standards of health and safety in the mining industry. In U.S. coal mines, a new era was ushered-in in 1969 for the control of health hazards from respirable coal mine dust. Since then significant progress has been made on all aspects of the respirable dust problem-its definition, monitoring, reduction, and control. In the intervening years, our ability to monitor, analyze, and characterize the mine atmospheric environment and the health of miners has increased many fold. Also, advancements in production technology have far outdistanced enhancements in environmental control technology. Therefore, questions are continuing to be raised on the adequacy of the characterization and control measures with regard to both the airborne respirable dust in mines and the health effects of respirable dust. Late in 1995, the Secretary of Labor appointed an Advisory Committee on the Elimination of Pneumoconiosis Amona Coal " Mine Workers (Dust Advisory Committee) to review the progress towards elimination of coal worker's pneumoconiosis (CWP) and silicosis, and in the program to control respirable coal mine dust in underground and surface mines, and make recommendations including improved standards and other appropriate measures for the control of exposure to airborne coal mine dust. The Committee's report was released in October, 1996. In this paper, a summary of the recommendations of the Committee is presented. A brief discussion of the background, and the issues and findings leading to the recommendations is also presented. The Committee concluded that the progress made towards making mines safer from the health hazards of respirable coal mine dust is substantial but that it is not sufficient to achieve the intent of the 1969 Coal Act. The Committee's recommendations encompass a wide range of issues addressing permissible exposure limits (PELS), sampling, dust control plans, hazard and medical surveillances, role of miners, training, and research and development.

Jan 1, 1997

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993