Search Documents

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By Dell H. Adams

Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining.

Jan 1, 1981

By Marcie A. Greenberg

The Fence Lake Project is located in the Salt Lake coal field, an extension of the San Juan Basin. Geologic formations exposed in the Project area range in age from late Cretaceous to Quaternary. Coal is encountered in the Moreno Hill Formation (upper Cretaceous). Salt River Project (SRP) followed the basic textbook approach for the exploration, regional appraisal, detailed reconnaissance, detailed surface appraisal and three dimensional sampling (physical exploration). SRP is exploring this property as a potential fuel source for the Coronado Generating Station. Therefore, for the physical exploration stage, the quality sampling program was designed from a utility company viewpoint to determine possible impacts to the Station. Exploration drilling was completed in spring, 1982; September, 1982, and summer, 1984. Engineering, environmental, and land acquisition studies were added in the Summer, 1984 Program to more closely evaluate the potential Fence Lake Project coal supply option for the Coronado Generating Station. Studies, including drilling, are ongoing-at this time.

Jan 1, 1984

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By Robert M. Weidenhammer

For years before the war, Coal had the reputation of being a sick industry. Currently it is operating at peak production and succeeding pretty well in keeping out of the red. But, says Mr. Weidenhammer, it will have a relapse as soon as the war ends unless (1) working capital can be built up; (2) it gets the support of the people and Congress; and (3) a truly long-range national fuel policy is formulated.

Jan 1, 1943

By D. A. Grieve

"Mineable coal seams in the East Kootenay region belong to the Mist Mountain Formation of the Jurassic -Cretaceous Kootenay Group. Three structurally separate coal fields (Crowsnest, Elk Valley and Flathead) are recognized, all of which are characterized by compressional tectonic features such as f aiding and thrust faulting, and by /ate-stage normal faulting. Tectonic history has greatly influenced coal mineability and quality. Coals range in rank from low to highvolatile bituminous, and reactive maceral content ranges from less than 60% to greater than 90%. A wide range of metallurgical and thermal coal qualities is found. Measured reserves (up to 1981) include 1.03 billion metric tonnes metallurgical and 165 million metric tonnes thermal coal. Introduction a) Location -Coal fields of the East Kootenays region occur in the Front Ranges of the Rocky Mountains, within 30 km of the Alberta -British Columbia boundary (Fig. 1). They extend over 175 km north from near the U.S. border, and occupy the regions of the Crowsnest Pass and Elk and Flathead River drainages. The deposits are accessible from Highway 3 (Fig. 1) and various secondary roads. The towns of Fernie, Sparwood, Elkford, Coleman and Blairmore serve the coal industry. East Kootenay coal deposits are contained in three structurally separate coal fields, the Crowsnest, Elk Valley, and Flathead coal fields (Fig. 1). Coal is currently being produced by B.C. Coal (now Westar Mining Ltd.) at Sparwood, by Fording Coal 20 km north of Elkford, by Crows Nest Resources at Line Creek 15 km southeast of Elkford, and by Byron Creek Collieries at Corbin. Westar Mining has also constructed a new mine on the Greenhills Range 8 km northeast of Elkford. Pre-requisite engineering and environmental studies have been carried out on the Elco Mining property, 35 km north of Elkford, and on the Sage Creek coal property near the U.S. border (Fig. 1). b) Coal land tenure -Coal rights in the East Kootenays are either held as freehold land, or are licensed from the provincial government. The former category includes lands acquired under the Railroad Act of 1890. Shortly after this the federal government also obtained 50,000 acres of coal-bearing lands from the Crown Provincial, the so-called Dominion Government Coal Blocks. Major holders of coal rights in the area are Westar Mining and Crows Nest Resources. Large blocks are also held by Fording Coal and related companies, Sage Creek Coal, and Canada Permanent Trust Company as trustee for Elco Mining, and small blocks are held by Byron Creek Collieries and Coleman Collieries. In addition the provincial government holds an area in reserve for possible future use of B.C. Hydro at the extreme north end of the Elk Valley coal field."

Jan 1, 1985

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By Frank F. Aplan, G. Rinelli

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By A. V. Nguye, P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration. Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. A possible mechanism, based on the existence of the pre-existing submicron-sized gas bubbles, known as bubstons (i.e. bubbles stabilized by ions), present in water in close proximity to the hydrophobic coal surfaces is discussed in line with the early observation of flotation improvements by microbubbles “nucleating” on hydrophobic surfaces. In particular, the dependence of the bubble-particle attachment efficiency on electrolyte concentrations supports hypothesis on the salt-dependent and ion-specific existence of bubstons. However, a theoretical explanation of the transition salt concentration (at about 0.1M) is deficient at present. The existence of these submicrobubbles in close proximity to hydrophobic surfaces is not trivial. They can (as can individual gas molecules or other solutes) mediate and extend the range and magnitude of the attraction between hydrophobic macroscopic surfaces. These bubbstons may explain the curious phenomena of the socalled long-ranged hydrophobic attraction measured with the Surface Force Apparatus and Atomic Force Microscopy, and the slippage at hydrophobic surfaces. Finally, the coalescence of bubbstons affects the rupture of liquid films at a very large thickness (over 100 nm), observed, but unexpected, by flotation chemists.

Jan 1, 2003

By S. C. Sun

[There are significant quantities of anthracite silt deposits in Pennsylvania, known as 'liver silts" (l,2). These contain from 20 to 55 per cent of non-combustible materials, the major portion of these impurities being clay slimes. Both the anthracite coal and impurities are mostly of extremely fine particle size. The utilization of these raw silts in power-plants faces such serious problems as, handling difficulties causing plug-up in equipment, disposal of enormous ash-residue, and corrosion. These problems may be solved by upgrading the raw silt with a cleaning process, which will be capable of removing most of the clay slimes and electrolytes.]

Jan 1, 1964

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By E. G. Bailey

PLANTS that normally burn coal now able too obtain a substantial increase over their normal supply for their greater power needs, and also additional tonnage for extra storage against the uncertainties of the future. Many plants previously burning oil or gas have already been converted to coal, and those which must yet change to coal will undoubtedly be able to obtain ample tonnage of coal of standard quality at reasonable prices. What a contrast this is to the conditions of 25 years ago, when the shortage of coal and transportation led to prices of $5 to $6 per ton at the mines, and degradation of quality, until the already overburdened railroads were called upon to haul 100,000 ton per day of extra ash alone. This was the result of a runaway market and the loading of gob, slate, and sub-quality coal amounting to an estimated increase in ash of 5 per cent of the total tonnage hauled. The problem of getting increased steam output from inferior coal caused unbelievable reductions in the low normal boiler efficiency of that time and untold labor in firing the hand- and stoker-fed furnaces of that day.

Jan 1, 1942

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981