Search Documents

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

In the estimation of recoverable resources, geostatistical techniques such as Multiple Indicator Kriging require a change of support correction to derive theoretical recoveries based on an assumed level of mining selectivity. The change of support models most widely used in practice entail model based generalized corrections either on a global or local basis. Examples include the affine and indirect lognormal methods. Change of support corrections derived empirically through short-scale conditional simulation realizations often show notable differences compared with theoretical corrections determined using model variogram parameters. The existing changes of support models are reviewed and an alternative method is proposed.

Jan 1, 1999

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole.

Jan 8, 1954

By Chester M. F. Peters

INTRODUCTION There has been considerable discussion in recent years of the strained relations between owners, engineers and contractors caused by the rapid increase in costly litigation in underground excavation due to construction claims. These time consuming claims are not to the best interests of the industry. It has been a conclusion of some of the concerned parties that there could be a substantial reduction in these claims if a mutual respect for each other's roles could be maintained along with a practical contractual arrangement for sharing the risks of the unforeseen costs inherent in the business. This paper will touch on the overall problem of these relationships, but confine the major discussion to the role of geology in claims and, in particular, changed conditions claims, since they form the base for the bulk of those involving geology. Geologists can make a major contribution to the reduction of these claims if their particular abilities are recognized and used properly. CLAIMS AND GEOLOGICAL RISKS The tunnel contractor is strictly bound by the contract he signs, and the risks he assumes thereby must be priced. The most important variable factor on which he must base his price is the geologic data provided and his interpretation of it. If this data does not give a clear picture of the conditions, making it impossible to price

Jan 1, 1974

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940

By R. A. Wagstaff

SINCE the time of the early Egyptians, the use of copper has been a boon to the life of most of the civilized world. Its use has been varied; in many connections, the art by which it attained its greatest usefulness has been lost. In this paper an endeavor will be made to take into consideration some of the many changes that have occurred during the last 40 years of copper-smelting operations. During that period the copper blast furnace has been almost forced out of existence by new methods of ore concentration-first, gravity concentration, and then flotation. These new methods of concentration introduced many new factors into the metallurgy of copper. The product was wet, it was fine and it was high grade. To overcome all these factors many changes have been necessary throughout the smelting agenda. New equipment has been necessary for transportation, unloading, sampling, bedding and moisturing in all smelting plants, especially the custom smelter. During the early days of "flotation," little was known about filtering or the use of an alkaline circuit; often the concentrate going to the smelter contained 20 to 25 per cent moisture. It is easy to imagine the difficulty arising with a product of this nature when it had to be shoveled by hand labor. To meet these conditions, mechanical unloading and sampling devices were soon developed. In many instances such good progress was made that actual costs for handling this unfavorable product were lower than those formerly incurred on the old product. Today most sampling of copper ores and concentrates is being done by mechanical sampling, pipe or augur sampling, or shovel sampling. Where concentrates are uniform in metal content, a great many of the plants now use pipe or augur sampling. For spotty ores, the old shovel sample with cone and quartering during the final stages is still in use. Where big tonnages are handled, mechanical sampling of concentrates is being done, with satisfactory results. To curtail slow and tedious cutting and mixing procedure, mechanical mixing boxes, splitters and cutters are used to cut down labor costs. MILLING As crude ores become scarcer, the use of milling operations increases. The few crude ores that are still smelted are used as fluxing types. To use these ores finer grinding has been found advantageous. This has made for better bedding and fluxing conditions, which in turn makes for faster smelting, lower fuel consumption and better metal recovery. The degree of fineness is more or less determined by the nature of the product. Most plants have set a standard of through ¾ -in. mesh screen for roaster- reverberatory smelting and through ¾ in. mesh screen for converter fluxes. For some refractory ores; even finer grinding has been found to be advantageous for good reverberatory smelting.

Jan 1, 1944

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By Treglown N

In any mining operation the curtailment of rising operating costs is of prime concern to management.One area of activity where costs are often disguised is that of longhole secondary breakage.This paper outlines sane operational techniques that have been considered and tested, resulting in improved fragmentation fran longhole stope blasts at New Broken Hill Consolidated Limited mine, Broken Hill, NSW.

Jan 1, 1985

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987

By A. K. Verma

This paper provides a brief overview of evolution of deformations, stresses, and pore pressures due to different excavation stages during construction of an URL. Excavation of a rockmass develops a damage zone of finite width around the excavated zone which is associated with changes in permeability and which affects the fluid flow mechanism. In this study, a coupled hydromechanical (HM) analysis has been conducted for a water saturated porous rock mass which has been created by sequential excavation and backfill of vertical disposal pit of an URL. For this purpose, an Atomic Energy of Canada Limited?s in-floor concept for a deep geologic repository suitable for Indian conditions has been used. Changes in rock deformations, stresses, strains and mechanically induced pore pressure in an undrained condition, during excavation, as well as those caused by mechanically induced rock deformations after backfill of the disposal pit, have been modeled. A three-dimensional finite difference tool FLAC3D has been used for the analysis.

Jun 1, 2012

By A. V. Castelli

The provinces of Guangxi, Guizhou, Hubei (and most recently Fujian) were the prime exporters of barite during this period. Guangdong and Shandong were exporters too but not major participants. These are all primarily agricultural areas so there existed a sufficient labor force willing to work in the mines to supplement their income from farming. During the early years, barite export pushed the existing transportation systems in these provinces to operational capacity. The mines from which this barite is extracted are located about 250 to 1,400 kilometers from the sea ports. Transportation of the ore from the mines to the ports follows a net-work that includes trucking to various rail-heads where it is then shipped via freight trains to ports for loading into seagoing vessels. in some instances, the barite travels by truck or train to the Yangtze River where it is then barged to an ocean port.

Jan 1, 1990

By E. L. Oliver

IN OFFERING a few comments and suggestions on trends in mining practice, and the methods and tools of tomorrow's mining, perhaps it will be appropriate to start with the subject of education. Charles Kettering, one of the best-known scientists and experimentalists in the automotive industry once said, in effect, that tech- 111ca1 schools have to be carefid not to teach a lot of hard and fast rules that may have been true once, but aren't so any more, or won't be presently. Possibly the mining school of the future will concern itself less with what has happened and more with what is going to happen. It will be built about or around problems. Such a school will be judged, not by the number of its students but by the quality of its improvements. To such a school the industry will send for men to solve particular problems. The industry will doubtless at some time sup- port such a school financially though a lot of hard work will be required to organize miners to undertake such financing, primarily because the mining industry, other than that concerned with iron and steel, is too loosely knit. Each company tends to its own knitting too closely for its own good. Wouldn't it be splendid if the mining industry would finance a "problem school" as suggested by Mr. Kettering and others.

Jan 1, 1939

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the 'first-generation' methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By W. K. Hartley

INTRODUCTION AND HISTORY The Kimberley Division of De Beers Consolidated Mines Limited includes four underground mines in Kimberley viz. Dutoitspan, Bultfontein, De Beers and Wesselton Mine and two outside mines, viz. Finsch, an opencast operation and Koffie- fontein, an underground operation. Figure 1 is a map of the Kimberley district showing the location of these mines. Finsch is 150km west of Kimberley and Koffiefontein is 80km south of Kimberley. The head office of the De Beers Company is in Kimberley. The diamond sorting and trading companies for diamonds produced in South Africa are also in Kimberley. Diamonds were first discovered in the Kimberley area at Hopetown in 1866 on the banks of the Orange River. This, and later finds, triggered the start of the great "Diamond Rush". In 1870 the Jagersfontein (now closed) and Dutoitspan pipes were discovered, followed by those at Bultfontein, De Beers and Kimberley Mine (now closed) in 1871, Koffiefontein in 1880 and Wesselton in 1891. Finsch Mine was a more recent discovery in 1961. Finsch, due to go underground in 1986, and Koffiefontein, are fully self-contained with their own treatment plants, housing, services etc. The four Kimberley mines deliver ore by conveyor to a central treatment plant and use joint ser- vices. ,+lining is presently carried out mainly by Block Caving which has replaced the earlier Chambering method. De Beers Mine, on a limited scale, and Wesselton Mine have recently started to use Sub-Level Caving, and both Bultfontein and Du- toitspan are scheduled to use the same method at a later date. The combined ore tonnage produced by the Kimberley Mines is 17 400 tons per day, Koffiefontein 12 000 tons per day and Finsch Mine 17 000 tons per day. THE EVOLUTION OF MINING METHODS Initially, the open-cast mining was carried out to as great a depth as safety would permit. In the early stages of open-cast mining, the Kimberlite was removed in horizontal slices from levels 13m to 20m apart. The rock broken in the workings was raised to the surface by means of endless rope haulage inclines. As lower levels were attained these rope haulages were replaced by aerial hoists, inclined shaft haulages or inclined skip-ways. These methods were dependent upon the strength of the unsupported pipe walls, which became increasingly unstable with depth and a system was adopted whereby the ground mined in open excavations was tipped down passes to tunnels connecting with vertical hoisting shafts sunk in the country rock. As work in the open pit became more and more impracticable due to extensive falls of ground, this system was replaced by a combination of open-cast and underground mining, and eventually by wholly underground methods. Chambering With the advent of underground mining, a system known as "Chambering" (or "Inclined Chambering") was evolved. It was essentially a combination of shrinkage stoping and caving, whereby advantage was taken of the high pressure exerted by the loose rock that had accumulated in the open excavations due to the collapse of the pipe walls. This mining method was introduced around 1890 and was successfully employed, with little change, up to the early nineteen seventies. In this system each mine was served by a main hoisting shaft situated about 300m in the country rock. Main haulage cross cuts were driven from the shaft to the pipe at 200m (600ft) vertical intervals. A sub-vertical shaft, situated close to the pipe provided access to the working levels. Chamber levels were established from the sub-vertical shaft at 13m (40ft) intervals. See figure 2. On each of these levels successive 6,8m wide “cuts" were mined out across the pipe, from one rock contact to the other, and extended vertically to the footwall of the level above. Every 6,8m cut was made up of a chamber and a "back-pillart1, each approximately 3,401 wide. The chamber was mined by overhand shrinkage stoping. The levels were carried "en echelon", with each chamber on a level approximately three cuts ahead of the chamber on the level

Jan 1, 1981

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960