Search Documents

By T. S. McGahey

The southeastern region of the United States has long been a major market area for coarse and medium particle size natural ground calcium carbonate fillers. The primary market for calcium carbonate in the southeast traditionally has been as fillers in building materials such as carpeting, joint cement and roof shingles. In these applications the economic value of the calcium carbonate in the final product is weighted more toward lessening the cost of the final product, as opposed to contributing any desirable physical characteristics. For example, in carpet backing applications the calcium carbonate filler does little more from a physical standpoint than add weight and body to the backing adhesive. The important factor in the use of calcium carbonate in carpet backing is that it can be used at high loading levels to replace the more expensive latex binder, thus lessening the cost of the final product. It is estimated that calcium carbonate producers in the southeast sell in excess of 200,000 tons (181,436,000 kg) annually for use in latex compounds for carpet backing applications.

Jan 1, 1986

By J. J. Fallon

Las Vegas is a place of many distractions. It is difficult for one to apply himself to sophisticated technical matters in the midst of gambling, liquor, scantily clad young ladies and the top entertainment available in the United States. But, I know that the men and women of SME are made of stronger stuff and will not be tempted by these things.

Jan 1, 1989

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

By E. D. Goddard, D. S. Murphy

Acid resistance, zeta potential and ESCA (electron spectroscopy. for chemical analysis) experiments were performed on emperador marble and four calcium carbonate samples (onyx calcite, travertine calcite, Iceland spar calcite and aragonite). Six fluorine-containing reagents were used to treat the surfaces of these materials: magnesium hexafluorosilicate, zinc hexafluorosilicate, sodium fluoride, zinc fluoride, strontium fluoride and stannous fluoride. The acid resistance of treated samples proved to be much higher than that of their untreated equivalents. The isoelectric point of treated samples approaches the isoelectric point of fluorite. Also, the fluorine content, as measured by ESCA, of a marble surface treated with magnesium hexafluorosilicate is much higher than that of an untreated sample. The binding energy off of fluorine and calcium the treated marble is consistent with the formation of calcium fluoride.

Jan 1, 1994

By Y. I. Rabinovich, S. C. Brown

In the Florida phosphate industry, fatty acid collectors are used to separate phosphate ore from silica during the rougher flotation stage. However, the presence of multivalent ions (in particular Ca++) in the processing water has been reported to result in the activation of silica with respect to oleate adsorption, rendering it floatable. Hence, adequate separation may not be achieved during the rougher flotation stage. In this study, the direct measurement of surface inter-action forces via atomic force microscopy was used to delineate possible mechanisms for calcium activation under phosphate flotation conditions at oleate/calcium concentrations both above and below the calcium dioleate precipitation limit.

Jan 1, 2004

By Quanjun Liu, Rongping Lin, Rongdong Deng

Arsenic contamination significantly affects the quality of copper concentrates, presenting challenges during smelting processes. Considering that covellite and enargite have similar surface properties, they are difficult to separate by flotation, resulting in copper concentrates with excessive levels of arsenic. To address this issue, this study systematically investigated the flotation separation of covellite and enargite in microflotation and bench-scale flotation tests using calcium lignosulfonate as a depressant, with the results indicating that calcium lignosulfonate can be used to separate covellite and enargite because it enables the separation of arsenic-bearing copper minerals into high- and low-arsenic (As 0.57%) copper concentrates. According to contact angle and adsorption tests, scanning electron microscopy–energy dispersive spectroscopy, and X-ray photoelectron spectroscopy, the differential adsorption of calcium lignosulfonate onto covellite and enargite is the primary reason for their distinct flotation behaviors in the presence of calcium lignosulfonate. The selective depressive effect of calcium lignosulfonate provides a novel approach for improving the flotation separation of arsenic-bearing minerals from copper sulfide minerals.

Feb 28, 2024

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By S. M. Narbekova, L. V. Semushkina, Zh. A. Aldybayeva, A. A. Mukhanova, D. K. Turysbekov, N. K. Tussupbayev

More complex and heavy-concentrating oxidized and mixed sulphidic oxidized ores are involved in production because of increasing needs for non-ferrous metals. Extraction of the oxidized minerals of non-ferrous metals general in current technologies. The problem is solved to oxidized polymetallic ores the preliminary selective sulphidization is the oxidized surface of the components by means of hydrogen sulphide, sulphide and calcium polysulphide, and also element sulphur, etc. The task was to study details of flotation of the oxidized lead-bearing ore of the Zarechnoe deposit (Kazakhstan) with calcium polysulphide as sulphidation. According to chemical analysis initial samples of the ore contain, %: lead – 4.8; zinc – 0.1; general iron – 0.81. Phase structure lead is characterized by the oxidized form of 57.76-64.5 %; by sulphidic status of 25.5-32.64 %, and by plyumboyarosite of 19.0-23.02 %. Researches on flotation beneficiation of oxidized lead-bearing ore are conducted. Sulfidizator gave to grinding, on flotations there were used the collector (butyl xanthogenate of sodium) and frother (T-80). Experiments were conducted with a new sulphidizator – calcium polysulphide. The latter is obtained by interaction of CaO calcium oxide with sulfur and water at high temperature with component mass the following ratio S:CaO:H2O =10:5:85. Extent of mill initial ore was optimised (88.42 % of - 0.071 mm grade). For the optimum mill mode the studies on matching of an optimized consumption of sulphidizators are performed. On basic technology with application of sulphide of sodium as a sulphidizator at optimum mill, the lead concentrate with the content of lead 64.4 % at extraction of 86.6 % was received. The content of cerussite in a concentrate was about 14.9 % at extraction of 82.1 %. With application of calcium polysulphide as a sulphidizator the lead concentrate with the content of lead 68.0 % at extraction of 88.0 % was received. The content of cerussite has made 16.0 % at extraction of 85.0 %. Application of a new sulphidizator allows to increase extraction of lead in a concentrate from 64.4% to 68% and cerussite extraction – from 82.1 % to 85.0 %. The possibility of application of calcium polysulphide as a sulphidizator instead of conventional sulphurous sodium was established.

Jan 1, 2018

By B. R. Davis, Neale R. Neelameggham, R. E. Brown

The element Calcium element has a unique place in the production of etals, intermetallics and other compounds. The unusualness arises from the fact that we have several possible reductants – metallic calcium, calcium carbide, calcium cyanamide and calcium hydride. A review of how metallic calcium is manufactured and utilized is presented. The difficulties involved in producing the metal in large quantities and price implications are noted. . Fundamental thermodynamics of how these act as reductants are shown, along with the historic application of these in metal production during the past century and a half. Alternate applications as to how to control the cost of the reductant is indicated, such as the numerous attempts in making low cost titanium utilizing direct or indirect calcium reductant.

Jan 1, 2014

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By Theodore R. Butkovich, Jesse L. Yow

Geological storage of spent-fuel assemblies from an operating nuclear reactor has been underway since the Spring of 1980 at the U.S. Department of Energy's Nevada Test Site. The primary objective of this generic test is to evaluate granite as a medium for deep geological storage of high level reactor waste and to provide data on thermal and thermomechanical behavior of granite from imposed heat loads.(l) The underground installation in the Climax stock granite was sited at about 420 m below the surface and 145 m above the existing water table. As shown in Figure 1, three parallel drifts were excavated spaced on approximately 10 m centers. Seventeen storage holes were drilled at the central drift on 3 m centers in which eleven spent fuel canisters and six thermally identical electrical simulators were emplaced. Electrical resistance heaters were emplaced in vertical holes in the floor of the side drifts on 6 m centers. The thermal output of these heaters is being periodically adjusted to simulate the thermal response of a large storage array. Rock and ventilation air temperatures are being measured continuously in the drifts and throughout the rock surrounding the excavations. Measurements of drift deformation have been made routinely since the emplacement of the spent fuel. Both vertical and horizontal measurements are being taken at five locations along the heater drifts and at six locations along the central canister drift (Fig. 1). Two types of instrumentaton are being used: convergence wire extensometers which are monitored automatically, and a manually operated tape extensometer with which measurements are taken periodically. The tape extensometer measurements were initiated about 6 weeks following fuel emplacement. The lack of a temperature correcting capability for the convergence wire extensometers make that data unavailable for analysis at this time.

Jan 1, 1982

By Janice K. Means

The purpose of this paper is to provide the seminar attendee with: information on pipeline construction, operation and standards to better equip him (or her) to analyze the ultimate effect of blasting stress on pipelines; an introduction to the analysis of blasting effects to pipelines using the American Gas Association analysis method; and; supplemental sources useful in the analysis of blasting effects to steel pipelines, and, in particular, on natural gas pipelines.

Jan 1, 1992

By Charles J. Speake, Dennis R. Haley, Thomas E. Finch

The tremendous interest in development of surface- mineable coal throughout the western US will bring with it a requirement for many manhours spent in mine planning and equipment selection. One problem in particular that engineers face during the planning stage is that of selecting a dragline with the proper reach capability. Reach, expressed in terms of operating radius and effective spoil radius, can be a major problem when mining deeper than originally planned, and aside from production requirements, the ability of a particular dragline to spoil across a strip is essential. Determination of dragline reach needed for a multiple-seam western coal operation can be simplified by use of an equation derived below that eliminates the need for tedious and repetitive calculations.

Jan 5, 1977

By D. Limpitlaw, A. Alsum, D. Neale

"Ecological footprint analysis (EFA) was first described in 1996 as a measure of carrying capacity appropriated by human activities. EFA is a resource and emissions accounting tool designed to track the demand on the biosphere’s regenerative capacity. Ecological footprints are increasingly used as indicators of organizational and corporate environmental performance and product sustainability. There is a compelling argument to develop an EFA tool for mining companies.To determine the size of a mine’s ecological footprint, land requirements for all categories of consumption and waste discharge must be summed. This land is only made up of the ecologically productive land and water in various classes (cropland, pasture, forests etc.) required on an ongoing basis to provide all energy and material resources consumed and absorb wastes.A challenge in conducting an EFA for a mine is the shortage of accessible data. Undertaking an EFA for a corporation or individual site entails compiling consumption and emissions data (which can be used for other reporting applications). The footprint results themselves highlight the most critical aspects of an organization’s impact on the environment and provide a platform for focusing actions and for educating the workforce to improve their contribution to best-practice operations. This paper discusses the benefits and challenges of undertaking an EFA for a mining company, and provides examples of the various components of ecological footprints associated with mines, as well as showing how an EFA can be used to understand and communicate some of the impacts associated with mining activities.IntroductionFundamental biophysical and economic limits are now being experienced in many countries around the world. Herman Daly, a former World Bank economist, described this scenario as ‘uneconomic growth’, where the costs of growth exceed the benefits (Daly, 2005). This occurs when the economy’s expansion encroaches excessively on the surrounding ecosystem, sacrificing natural capital. Under such conditions the sacrificed natural capital is more valuable that the resulting economic growth. Consequently, the world faces largescale threats to sustainability and especially to the viability and continued existence of the ecosystems that support human settlements (El Zein et al., 2014). In recognition of this sustainability imperative, mining companies are increasingly concerned with their ecological footprint (EF)."

Jan 1, 2017

By R. F. Hewlett

All ore reserve estimates are based on some system for assigning an area of influence to each drill hole. Commonly used methods of calculation are the polygonal, triangular, statistical analysis, and cross-sectional. Each of these methods is based on different volumetric considerations and the weighting of grade with tonnage varies with each method. Because the characteristics of each mineral deposit are different, a preliminary survey of these characteristics should be made for each individual deposit to determine which method or methods should be used. In this project the several methods were not only compared with one another, but also against actual production records. Basic data was derived from a mined out portion of the Silver Bell pit near Tucson, Ariz. All calculation was carried out on a digital computer, and the first step was development of computer programs which would yield the desired information. The second step was the coding of input data into punched card form. Cost and speed of computer operation were measured, and these results are given with the computer program summaries on page 38.

Jan 1, 1961

By Catherine Johnson, Kelly Williams

Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount

Feb 1, 2020

By E Cunha, D Roldao, TáTamantini, J F. C L Costa, T Webber, C Monteiro

The main problem of geostatistical simulations is to reproduce the real characteristics of the mineral deposit when there are few conditioning data. In this case, the geological interpretation, based on structures, geophysics and geological maps, plays the major role in terms of resource evaluation.The paper investigates the use of principal component analysis (PCA) to help classify multiple geostatistical categorical simulations considering the similarity among them and the interpreted model, herein referred as training image (TI).An iron deposit with four lithological facies, in a specific horizontal plane, was used as case study for two-dimensional (2D) simulations. Sequential indicator simulations (SIS) was used to obtain ten equally probable 2D images, which were generated and compared against the interpreted model (TI).In this study, 11 random variables are comprised by the vector of ten SIS realisations plus the training image (TI). The similarity between the TI and each SIS realisation is measured using the angle between the TI and SIS vectors projected in the new coordinate systems (PCA factors). It is possible to order the SIS realisations from the highest to the lowest PCA factor taking into account the TI similarity.The visual analysis of the images shows coherence in the PCA results as a method to measure similarity. This methodology can be used as a post-processing tool to rank simulation results and to select the ones which better represent the prior known geology or to compare the quality of different methods of simulation.

Sep 26, 2011

By Krzysztof Tajdus

In Europe, horizontal strain is a primary parameter for estimating building hazard resistance. Other measured indices, like curvature, are less important, since in most cases of European excavation depths are very large (about 1,000 m (328 ft)) and, in such circumstances, curvature influence decreases. Therefore, a proper description of horizontal displacement (and strain) in the scope of minimizing influence is essential. This article presents a development of European methods of horizontal displacement and horizontal strain calculations, as well as current solutions in this respect.

Jan 1, 2011

By T Honeyands

At present we are witnessing large investments in the iron ore industry, fuelled by demand from Asia. At the same time, there is a changing landscape in pricing of iron ores, with the recent demise of the benchmark system and the evolution of market based index pricing systems. From a customer perspective, it is the behaviour of iron ores in downstream processing that gives them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions, and in setting quality price differentials.This paper describes the use of the Marx value in use (VIU) model to quantify the downstream value of iron ores. The Marx model consists of heat and mass balance modules for sintering, pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples given for the relative value of haematite, Marra Mamba, and channel iron deposit (CID) ores.

Jul 11, 2011