Search Documents

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By J. O. Mack, J. B. Russell

In recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. Table i.—Composition Ranges Prescribed for a Commercial Substitute Solder Element Per Cent Tin............................ 18.0-20.0 Bismuth (maximum)a............ 0. 80 Silver.......................... O. 10-1. 25 Bismuth plus silver (minimum).... 0. 85 Antimony (maximum)............ o. 50 copper (maximum),,,,,,,,..,,,, 0. I3 Other elements, each (maximum)6 0.03 Lead........................... balance a When silver is present in excess of I per cent, the Bi content shall be 0.50 per cent or over. b Total not to exceed 0.10 per cent. The Purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing 18 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic I5-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wet-tability, that will enable it to be used on the metals in common use. Basic Considerations The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat. If a soldering iron is used, it must not only

Jan 1, 1945

By Robert I. Jaffee, Bruce W. Gonser, Eugene M. Smith

There has been little investigation of the gold-germanium binary alloys. Haughtonl does not mention any work on the system. In a review article commemorating the fiftieth anniversary of the discovery of germanium, E. Einecke2 mentioned a gold-germanium eutectic at 24 atomic per cent Ge (10.4 weight per cent) melting at 359°C., but did not give the source of his information. From measurements of electrical conductivity, J. 0. Linde3 estimated that at least 0.6 weight per cent germanium is soluble in gold. The recent availability of germanium in this country in commercial quantities has led to interest in its properties and its alloys. This study is part of a program of investigation on germanium alloys; work on ternary alloys involving germanium and gold will be reported later. In this investigation, the composition and melting point of the Au-Ge eutectic reported by Einecke has been found to be substantially correct. Eutectic composition has been placed at I2.0 per cent germanium, however. An alloy of 10.4 per cent Ge, Einecke's value, was found to have a few gold dendrites in it. The cutectic temperature has been determined as 356.0 6 ± 0.5°C., slightly less than the temperature of 359°C. reported by Einecke. The liquidus curves and the solid solubility of ger- manium in gold have been determined, and are shown in Fig. I. Materials and Alloying The germanium used in this investigation was prepared by the Eagle-Picher Lead Co. from pure germanium oxide, by reduction in clay crucibles with sodium cyanide. The regulus is quite pure, assaying over 99.9 per cent Ge. High-purity gold obtained from Handy and Harmon was used. Alloying was carried out in graphite crucibles in an atmosphere of purified hydrogen. The temperature was brought up to 1050" to iioo°C., and the metal was allowed to freeze in the crucible. Prepared in this way, the gold dendrites in hypoeutectic alloys were somewhat segregated at the bottom and sides of the ingot, and on the hyper-eutectic side the lighter primary germanium tended to gather at the top. Most of the alloys were made from virgin metal. Low-germanium heats were made by alloying pure gold with the eutectic. Melting losses were consistently a few milligrams or less, and the composition could safely be taken from the intended analysis. The 30 per cent and 50 per cent germanium heats for thermal analysis were made in part from remelted higher germanium heats, and they may be OR composition as much as one per cent. Because of the high cost of materials, the weight of heats for thermal analysis were 15 to 20 grams and heats for metallo-graphic, X-ray, and hardness specimens were 2 to 4 grams.

Jan 1, 1945

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Processes in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carbonization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1, 2 Taggart,3 and Peele.4 Shape In general, coal differs in shape from its accompanying dirt throughout the range of commercial sizes. Coal, breaking into roughly cubical particles, contains a greater number of axes that are approximately the same length than does the dirt. The latter, consisting of pieces of slate and shale and lenses of pyrite, is flatter in nature. Further, flat coal often has a dirty, slaty appearance, even though of high quality. Mechanical pickers known as flat pickers, or "flatters," are widely used in the Pennsylvania anthracite region to remove flat coal .from the final clean coal. This practice greatly improves the appearance of the final market product. Flat pickers for removing impurities or flat coal ("flats") are usually installed on shaker screens, shaking conveyors, and chutes. In Fig. 1 three

Jan 1, 1950

By John Metz, D. E. Macdonell

The Falconbridge ore body, on the southeastern periphery of the Sudbury Basin, is definitely associated with a strong shear zone along the norite greenstone contact, in contrast to the "offset" ore bodies sometimes found in this district. To all practical intent and purpose, the dip is vertical. The ore varies in width from a few inches up to 90 ft., the average width being 15 ft. The present zone of mining operations is 6000 ft. long, 85 per cent of which develops commercial ore. The ground on the whole, and especially in the narrower widths, gives rise to reasonably strong self-supporting backs in most places, but the walls, because of strong post ore faulting on both norite and greenstone contacts, tend to be weak, and, at times, slough to a considerable extent. Obviously. then, with vertical dips, strong backs and weak sloughing walls, flat-back cut-and-fill methods are applicable to the Falconbridge ore body, and at present about 70 per cent of the stoping production is obtained in this way. The general method is described in the following pages. In actual practice, there are continual variations, as the mine staff feels that only in that way can new and better methods be developed. Source of Fill The overburden at the property consists of glacial sands and gravels, varying in depth from 00 at the outcrops, which are few and far between, to 150 ft. This condition makes for high initial cost of shaft sinking, always entailing spiling and concrete, but this extra expense is more than compensated for by the fact that the overburden is the source of very cheap fill.

Jan 1, 1946

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By C. W. Allen, L. C. Moore

The Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming. on the Marquette iron range in Michigan&apos;s Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleve-land-cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. Geology The north footwall of the Marquette Range synclinorium outcrops near the north line of set. 2, the iron formation dipping to the south at an angle of about 40. The south side of the trough reappears at a distance of 4J5 miles on sec. 26 and the surface geology between shows iron forma- tion or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850 ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 Per cent P, 5.40 per cent Si, 2-87 Per cent A1 and 0.015 per cent S. Exploration A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1946

By G. A. Koehler

The Hiawatha mine, a producer of iron ore, is near the City of Iron River, in Iron County, Michigan. This mine, operated by The M. A. Hanna Co., has been chosen by the author as a typical iron mine in this district that is using the cut-and-fill mining system. General Geology The Hiawatha ore body lies along the steeply dipping north limb of a syncline that closes around on the east end to form a bathtub-shaped structure. Throughout this major structure there are very many smaller wrinkles or folds, which vary the direction as well as the thickness of the ore body. The total length of the ore formation with minor interruptions so far developed is about 3600 ft. The ore body throughout the entire present depth of 2000 ft. has averaged approximately 40 ft. in thickness; it is somewhat narrower at the upper levels and shows a marked increase in thickness on the bottom levels. This increase in thickness probably indicates that the bottom of the trough is near or that a major monoclinal fold has been encountered, which flattens the ore and gives apparent horizontal thickening. The footwall of this ore body is generally a black, graphitic slate, very rich in iron sulphides, quite combustible when exposed to air, and very treacherous to handle during mining operations. The hanging wall, in most places, is a cherty, fairly hard iron formation, and in general stands quite well ill open stopes. There are places, however, where black slate is found in both the hanging wall and the footwall, which makes mining difficult, as the black slate tends to slough off after being exposed to air. In these places it becomes necessary to leave a scale of ore 5 to 6 ft. thick on both hanging wall and footwall, which is not recovered. Fig. I shows a typical vertical cross section through the Hiawatha ore body. Type of Stoping Because of the size and shape of the ore body and the hard, dense structure of the ore, sublevel stoping has been an efficient and economical method of extracting the ore. This method, with various minor changes, has been used since the mine was opened in 1893. There have never been any stope-filling operations, however, until recent years, when crushing of pillars and black-slate fires forced the issue and methods were arrived at to fill all stopes. Development of Deeper Levels Shaft sinking to deeper levels in development operations has been done successfully by two methods without interference or hindrance to production. These systems are: I. Sinking an auxiliary winze a short distance from the shaft, then drifting back to the shaft location and putting up a pilot raise through to the bottom of the shaft. This raise is always in the manway compartment of the shaft, so that no work is ever done under a cage or skip. A 20-ft.

Jan 1, 1946

By L. F. Bishop

The ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company&apos;s properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill is a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various methods in use for the second six months of 1944 are shown in Table I. This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1946

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer&apos;s causes. The second cause will be discussed first.

Jan 1, 1929

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS, * LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer&apos;s causes. The second cause will be discussed first.

Jan 1, 1929

By C Switzer, R Logan, S Konopa, P Stoker, R Lewis

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Misima gold mine, located on Misima Island within the Milne Bay Province of Papua New Guinea, was operated by Misima Mines Pty Ltd, a subsidiary of Placer Dome Asia Pacific Limited (Placer), between 1988 and 2004. During this period, the mine produced 3.7 Moz of gold and 22.2 Moz of silver. In June 2012, the Special Mining Lease for the property was surrendered and incorporated into an Exploration Licence (EL). WCB Resources Ltd (WCB) entered into an exploration farm-in agreement with Pan Pacific Copper covering this EL.In June 2013, WCB published a new mineral resource of the Umuna deposit at Misima. All the drill hole data used for estimation was historical data collected by the previous owners of the Misima mine between 1977 and 2001. No new drilling was carried out by WCB. Confidence that the data could be relied on was provided by detailed interrogation of the existing data, reconciliation of the new resource model against production data and significant input from individuals who had previously been involved with the data collection, resource estimation and production activities of the Misima mine during its operation.This extended abstract will consider the challenges associated with locating, retrieving and validating historical data to use as inputs to produce an updated Mineral Resource estimate and comment on the material value of appropriate data storage, documentation and record keeping through the life of a project. It will also comment on the value of WCB obtaining access to the intellectual knowledge of many professionals that were former employees of Placer. This knowledge ensured that all the historical data that should have been available was sought out and accessed.CITATION:Konopa, S, Lewis, R, Logan, R, Switzer, C and Stoker, P, 2015. Misima gold mine – a case study in the use of historical data for an updated mineral resource estimate, in Proceedings PACRIM 2015 Congress, pp 579–586 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70&apos;s. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Lucy England

The following is a summary of the Robert E. Murray Innovation Lecture on “Sustainable Copper Mining Flowsheets and the MissionZero Mine” presented as part of the keynote session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT. As the world accelerates its transition to renewable energy, the appetite for critical minerals such as copper, lithium, nickel, rare earths and graphite has never been greater. Forecasts suggest that global mineral demand will double by 2050, driven by the proliferation of electric vehicles, renewable power infrastructure and digital technologies. This surge presents not only an immense opportunity but also an unprecedented challenge. In a world where every ton of ore processed and every liter of water used is scrutinized, how can mining deliver more with less, while meeting tightening environmental and social expectations? Traditional mining methods, developed for an era of abundant, high-grade ore and looser regulations, are struggling to meet today’s demands. Declining ore grades, volatile markets and the imperative to shrink environmental footprints have rendered traditional mineral processing practices unsustainable. The sector thus finds itself at a decisive juncture, caught between the need to fuel the green economy, defense and artificial intelligence (AI) infrastructure, without compromising the planet’s future. Balancing these competing demands requires a paradigm shift in technologies and processes. FLS has responded to this challenge with MissionZero: an ambitious, holistic initiative to develop flowsheets for the future of mineral processing. This systemic approach aligns operational excellence with environmental responsibility. Integrating innovative technologies, digital intelligence and commodityspecific process designs, it offers mining professionals a roadmap to meet both production targets and sustainability goals. At the center of this approach is the belief that a more sustainable mining requires more than incremental improvement; it demands a fundamental shift in how we extract, process and manage resources. By developing tailored flowsheets for copper, gold, lithium and tailings reprocessing, FLS aims to set a new standard for efficiency, circularity and environmental stewardship. The message is clear. We must achieve more with less: less energy, less water, less waste.

Mar 1, 2026

By Karen M. Kessen

The isotopic variations of lead from Mississippi Valley galenas have long been used to place constraints on the sources of the lead, and on the residence the of the lead in crustal reservoirs prior to its emplacement in the Mississippi Valley province. Similar studies based on strontium isotope variations in gangue minerals associated with the lead-zinc sulphides have been neglected until Haden&apos;s (1) study of such minerals from several localities in northwestern Ohio. His work revealed two things about the mineralization. Firstly, it shoved that the average isotope composition of lead from galenas from northwestern Ohio lies on the anamalous lead line characterizing Mississippi Valley-type leads, albeit at the least radiogenic end of the entire data array. This confirm earlier assignments of the Ohio mineralization as Mississippi Valley-type (Hey1 and others (2)). Secondly, Haden (I) showed that the strontium in the calcite, strontianite and fluorite is broadly similar in isotopic composition to the strontium in the host Silurian to Devonian marine carbonates within which these minerals arc emplaced. He concluded that the mineral strontium my have been very locally derived, from the carbonate hosts.

Jan 1, 1979

By Guoxiang Chi

The Cornwallis Fold Belt in the Canadian Arctic Archipelago contains numerous Mississippi Valley-type (MVT) Zn- Pb occurrences and the world-class Polaris deposit. The occurrences are mainly hosted by the dolostone in the Thumb Mountain Formation which spreads over 25000 km2. Success in exploration requires further understanding of the genesis of these occurrences and an assessment of their parentage with the giant Polaris deposit. Syn-sulfide dolomites in regional occurrences share C-O-Sr isotopic characteristics similar with Polaris dolomites, indicating warm basinal brines enriched in 87Sr. The dolomites and sphalerites contain fluid inclusions with ice-melting temperature between ?45° and ?25°C, which is significantly lower than for most MVT districts in the world (?30° and ?10°C). These characteristics indicate that all the Cornwallis occurrences were produced by fluids of the same sources and/or aquifers. The deposit size was largely controlled by the rate and duration of the metal-carrying fluid flow, and by the availability of reduced sulfur at the site of mineralization.

May 1, 2001