Search Documents

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the intrusive, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust, these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EM SES NE% of sec. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamor- phosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or

Jan 1, 1950

By B. J. Walsh

ABSTRACT Segregation of sphalerite minerals in zinc concentrates into christophite, marmatite and ordinary sphalerite by means of magnetic fractionation is investigated. A Frantz ferromagnetic filter, 1.2 amp., and a Dings magnet, 0.3 amp., is used to fractionate seven zinc concentrates produced in the Province of Quebec. The Dings magnetic product contains the pyrrhotite, and the sphalerite as christophite. The Frantz magnetic product contains sphalerite as marmatite, while the Frantz nonmagnetic product contains ordinary sphalerite. The results indicate that the magnetic susceptibility of sphalerite increases with increasing isomorphous iron content and that a satisfactory separation into christophite, marmaite, and ordinary sphalerite may be accomplished by magnetic fractionation. INTRODUCTION SPHALERITE, the chief ore of zinc, is almost never pure zinc sulphide. Iron is almost always present isomorphously replacing an ?equivalent amount of zinc. What may be referred to as 'ordinary' sphalerite contains up to 10 per cent iron. More highly ferriferous varieties, with 10 to 26 per cent or more iron, have been named marmatite .and christophite.

Jan 1, 1951

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By R. Hans

Removal of toxic anions from aqueous solution was studied using a Magnetic Ion Exchange (MIEX) resin which is a polyacrylic, strong base resin. Gravity based settling is made more efficient due to the magnetic nature of the resin which is advantageous over conventional ion exchange resins. In addition, the magnetic microspheres of MIEX have larger surface area in comparison to conventional ion exchange resins. Over the years MIEX has been successfully used and has gained significant popularity for efficiently removing dissolved organic matter from wastewater and groundwater. In the present study the efficiency of the MIEX resin was tested for the removal of chromium(VI), molybdenium(VI), vanadium(V) and arsenic(V) anions. Effects of pH (2-10) and temperature (25oC-55oC) were examined. In general, low solution pH values were favorable for anion uptake by MIEX. Except for chromium(VI), the metal ion uptake was significantly increased by the increase in solution temperature. The adsorption data were analysed on the basis of chemical speciation and heterogeneous kinetic models.

Jan 1, 2014

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By Robert Steinitz

SOFT iron parts for magnetic applications, particularly pole shoes, constitute a major portion of the ferrous products of powder metallurgy. The residual pores in pressed and sintered parts reduce values such as the magnetic permeability but service experience extended over a number [ ] of years has proven beyond doubt that in many instances the lower density of powder parts is not prohibitive to their use m replacement of machined magnetic parts The. magnetic requirements for pole shoes particularly the permeability, vary within wide limits, especially with the relative size of the air gap in the finished assembly. The overall permeability of an assembly, µ, is given by the formula [ ] where µm is the permeability of the core material, l the total length of the magnetic path, and a the length of the air gap. Fig 1 shows the variation of the overall permeability with the permeability of the core material, calculated according to Eq I for an air gap of 1 pct of the total length of the magnetic circuit. It is readily recognized that to use core materials hav-

Jan 1, 1948

By W. Gundaker, F. C. Schwerer

Natural chromium-bearing spinels (chromites), which are used as refractory materials in basic steelmaking, are the only commercially important chromium ore and are also encountered as difficult-to-separate contaminants in ore deposits of potential economic value. Techniques for characterization and separation of ore materials frequently are dependent on the magnetic properties of the constituent minerals. An experimental program was initiated to explore the effects of temperature and of simple mechanical and thermal treatments on the static magnetic properties of several ore-grade natural chromites. Studies of the temperature dependence of the magnetic properties showed that the natural chromites, which are dilute in the magnetic ions Fe and Cr, order magnetically only at cryogenic temperatures. However, mechanical treatment in the form of crushing produces a magnetic component that is ordered at room temperature and that is of sufficient strength to alter magnetic-separation characteristics. The additional magnetic component apparently is associated with surface structures which develop during crushing and disappear after heating to above about 500°C. Preliminary studies indicate that this surface structure enhances the susceptibility of the chromite grain surfaces to gas reactions at moderate temperatures.

Jan 1, 1976

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By M. A. Bouchat

The Kipushi deposit, where the Prince Leopold Mine has been installed, belongs to Union Miniere du Haut-Katanga and is located in the Belgian Congo, 20 miles SW of Elisabethville, at the vicinity of the Northern Rodhesian Border. The deposit is of the hydrothermal metasomatic vein-type; mineralisation took place, through the limestone of the, lower Kundelungu. This is a special fea¬ture of the deposit, compared to the other copper deposits of the neighbourhood, both in the. Belgian Congo and in Rhodesia. Actually, the primary mineralisation of these other deposits; is directly related to the stratigraphic systems: schistous dolomitic in the Belgian Congo and Roan in Rhodesia. Both facies are older than the Kundelungu and separated from this formation by a tectonic cataclysm. The valuable elements occuring at Kipushi are principally copper; and zinc. The deposit also contains smaller quantities of lead, precious metals and other elements including germanium.

Jan 1, 1960

By L Semenyna, W Douglas

Gold is often present in solid solution with pyrite in the Carlin Trend. The presence of organic carbon along with gold hosted in sulfide, referred to as double refractory ore, requires that ore with high carbon-in-leach (CIL) preg-robbing potential and poor leach recovery is routed to a roaster. During roasting, the pyrite is oxidised to (ideally) form hematite (Fe2O3), and the gold that was present as solid solution in the pyrite forms colloids within the hematite. The ideal texture of the produced hematite is porous to allow for the penetration of cyanide for gold dissolution. Temperature and other conditions of roasting, as well as ore characteristics (pyrite mineral associations, arsenic) can affect the texture and the type of iron oxide formed. Many of these alternate iron oxide minerals result in incomplete leaching. Comprehensive gold deportment studies have proven that the majority of the gold losses in Barrick GoldstrikeÆs roaster leach tailings occur within the iron oxides created through the roasting process.The iron oxide phase that hosts the majority of the gold in tailings is in the form of by-product maghemite (?Fe2O3), which is highly magnetic. Barrick Goldstrike has designed a magnetic recovery circuit to capture these iron oxides, and with subsequent reprocessing, recover the lost gold. Pilot plant results and analysis using scanning electron microscope mineral liberation analyser (SEM MLA) shows that up to 30 per cent of the gold in tailings can be recovered with a three per cent overall mass pull to magnetic concentrate. This magnetic concentrate can be economically reprocessed, resulting in a three per cent improvement in roaster recovery.CITATION:Douglas, W and Semenyna, L, 2013. Magnetic recovery of gold-bearing iron oxides at Barrick GoldstrikeÆs roaster, in Proceedings World Gold 2013 , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By Kunihiko Yamaguchi, Gjergj Dodbiba, Toyohisa Fujita

Usually magnetic separation is performed to separate ferromagnetic, paramagnetic and diamagnetic particles by controlling magnetic field strength. In this research the wet high gradient magnetic separation at various kinds of magnetization of medium has been investigated to separate different kinds of magnetization of paramagnetic mineral particles from each other. Most of week paramagnetic particles are captured at high magnetic field using superconducting magnet. If the magnetization of fluid is larger than that of paramagnetic particle, the paramagnetic particle cannot be captured in the direction of magnetic field. The paramagnetic particles of different magnetization such as hematite, chromium oxide, perovskite and rutile are separated in different magnetization of fluids. These particles are present in the incinerated bottom ash. The separation is useful to recover titanium oxide from bottom ash and the removal of chromium of bottom ash is important to reuse the bottom ash as cement. The used fluids are paramagnetic liquids dissolving paramagnetic salts and the water based magnetic fluid dispersing the stable ultrafine magnetite. The dispersion condition of particles related to zeta-potential of the suspension feed is also important to separate effectively by controlling pH

Jan 1, 2014

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

All pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process,9-11 but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver's Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open- circuit roughing and closed-circuit roughing are best defined by the diagrams.

Jan 12, 1958