Search Documents

By Henry M. Howe

Jan 1, 1908

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

By Heinrich Ries

Jan 1, 1907

By G. Cartaud, F. Osmond

We have already devoted two previous memoirs to this question. In the firstL we collated and discussed the existing literature on the subject; in the second: we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allo-tropic states of iron—a, stable below A2; , stable between A2 and A3; and , stable above A3—all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, and did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier mas even led to think from some of our results that r-iron could very well be a rhom-bohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Jan 1, 1907

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By H. Hubert

The first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lurmann and to Lencauchez, who had pointed out the blast-furnace as a powerful gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgom Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Jan 1, 1907

By W. R. Ingalls

During the last two years, and especially during the last six months, a number of important articles upon the new methods for the desulphurization of galena have been published in the technical periodicals, particularly in the Engineering and Mining Journal and in Metallurgie. I proposed for these methods the type-name of " lime-roasting " of galena as a convenient metallurgical classification,'and this term has found some acceptance. The articles referred to have shown the great practical importance of these new processes, and the general recognition of their metallurgical and commercial value which has already been accorded to them. It is my present purpose to review broadly the changes developed by them in the metallurgy of lead, in which connection it is necessary to refer briefly to the previous state of the art.

Jan 1, 1907

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907

By O. E. Wheeler

The use of the walking dragline as a stripping tool has increased dramatically in the past two decades. The reasons for its increased popularity and some historical background on its introduction into the mines are given in a recent paper by Learmont. (l)* The history need not be recounted here except to show the trend to longer booms which has accompanied the growth in machine size. Figure 1 shows the change in maximum operating radius on Bucyrus-Erie machines which has occurred over the years and Figure 2 shows the corresponding change in maximum boom lengths. Reference 1 also presents some of the reasons for expecting this trend to longer booms to continue. There are many design parameters affected by the increase in boom lengths; swing power, hoist and drag rope lengths, and drum capacity, to list just a few. The purpose of this paper is to discuss only the structural implications of using longer booms. As in the design of any structure, the various facets of boom design are interrelated and a process of optimization between them must be worked out either by evolution or by conscious iterative effort. The decisions we have reached about such things as material selection, structural arrangement, and applicable criteria, have not come into being overnight but represent instead many years of design experience and a fair amount of recent concentrated analytical effort. In the following pages an attempt will be made to first, state those decisions, second, explain how we arrived at that particular result; and third, describe what we expect future developments to be which might influence us to change those decisions.

Jan 1, 1976

By Joanna LaForte

"IntroductionIn respect to The Human Dimension by M. Phyllis Bray, this author's impression is that research on long distance commuting (LDC) is long overdue. This type of mining is not new to many workers, especially those from areas such as the Maritimes, who have had to look for work away from their families for at least a decade. Perhaps to the industry the over-all set-up is new, but to workers who have faced mine shut-downs in their areas finding a job was the main objective and if the security of long-term employment was evident, then the families might join them later. This was the situation with which the writer' s family was faced.LDC LifestyleBeing the wife of an underground miner, the author has personally experienced this lifestyle for almost 10 years, and has never experienced accommodation in a company town. The first five years of marriage were spent in a small rural municipality within 50 miles of the worksite, but the town had industry separate from mining and was not affected by the mine shut-down.Since her LDC lifestyle began her family has been pretty much city-based, out-of-province commuters with two children and a third to arrive some years later. She therefore lived a fairly normal married life with a husband home daily. The author has experienced life with a husband who worked away for five-day stretches and then drove long distances to be home weekends or the portion of time left over from driving and fatigue. She has done the 3D-days in/l4-days out routine, and for approximately the past four years has been existing on a two-weeks in/two-weeks out ritual .The author does not agree that the ""bottom line is that mining families go where the jobs are"" . The miners go where the jobs are and the families fend for themselves with the assistance of the pay cheque making it home each pay period.Perhaps because there are many personal frustrations with this type of lifestyle, perceptions may be inaccurate. Having only dealt with underground operations, there may be gross differences between the pressures and demands of other forms of mining."

Jan 1, 1991

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By Siegmund Babendererde

1. Introduction In Sayreville, New Jersey, the Middlesex County Utilities Authority put the construction of a 1041 m long sewer outlet to tender in June 1989. It had an internal diameter of 3,36 m and was part of a sewage treatment works project for county Middlesex. The contract was awarded to the Lodigiani Company, USA, who employed Hochtief Incorporated as subcontractor to drive the sewer outfall. 2. Ground Conditions According to the preliminary geological site investigation, carried out by the consultants Metcalf & Eddy, the tunnel passed through marine deposits.

Jan 1, 1991

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By Karin Bäppler

Mechanized tunnelling is undoubtedly one of the most innovative disciplines in the international construction industry. Technological progress in the planning and production of most modern infrastructure is constantly striving for new records on basis of highly specialized solutions and know-how. Humans and technology have accomplished excellent achievements over the past few years in varied, difficult terrain. New length records are being set with the 64 km long Brenner Base Tunnel and the HS2 Railway system currently under construction in Europe. Cities are building ever longer and more demanding sewer tunnels. The paper highlights some of the challenges, trends and innovations of long-distance tunnelling projects.

Dec 1, 2022

By Christian Heinz, Doug Harding

TBMs can last for decades and be rebuilt project after project with proper maintenance. How successful can rebuilt TBMs be? At the DigIndy Tunnel System in Indianapolis, Indiana, USA, a rebuilt TBM was used to great effect. The 6.2 m diameter Main Beam, originally manufactured in 1980, bored 40+ km of tunnels and set three world records in its size class of 6 to 7 m, including a best month of 1,754 m. In this paper, the authors analyze the TBM rebuild, performance and lessons learned to make recommendations for future projects seeking to use rebuilt TBMs over long distances.

Jun 23, 2024

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017