Search Documents

By K B. Quast, A Schuurmans

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Limited. The effects of mill rotation speed, rod volume and ball size on the resulting product size distribution were investigated. Between 48 and 69 per cent of critical speed, the product sizing distribution curves remained very similar, with a finer grind resulting from increasing the speed of rotation at constant grind time. Increasing the rod loading from ten to 53 per cent by volume caused the product size to become finer and more closely sized with a transition occurring at approximately 29 per cent. This was interpreted as a change of dominant grinding mechanism from abrasion to impact. No preferential grinding of the cassiterite was observed. The effect of increasing ball size at constant charge weight was to preferentially grind the coarser particles and generate more intermediate sized particles, whereas the product from a mixed ball charge gave a distribution similar to that obtained when a charge containing only smaller balls was used.

Jan 1, 1998

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

It is possible to closely simulate the product sizing distribution from an industrial rod mill by the correct choice of parameters in laboratory batch milling. For laboratory batch rod milling, changes in per cent critical speed and per cent rod volume cause the product sizing distributions to move in parallel at a constant slope. For ball milling, larger sized media in batch milling grind more coarse material giving a closer simulation to the industrial rod mill product. Changing the feed size distribution by removal of coarse particles or addition of fine particles changes the product sizing distribution, but would not normally be practiced in laboratory testing. These data should be applicable to many instances where laboratory simulation of an industrial product size distribution is required.

Jan 1, 1998

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

The usefulness of laboratory studies - petrology and mineragraphy in the search for, and investigation of, mineral deposits should not be exaggerated, but it should not be overlooked, because such studies will always contribute to an understanding of the geology of the deposits, and can on occasions provide invaluable information not otherwise available. A few examples furnished by the investigations of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organisation will show this.Petrology.In the early stages of the investigation of the King Island scheelite deposit, during the war, when the nature of, the deposit was not understood, a series of samples embodying the exposed rock types was submitted to the Mineragrap;hic Section for petrologicalexamination by the Mineral Resources Survey. It was at once apparent to the petrologist that the King Island scheelite ore was a contact metamorphic deposit, in which a series of argillaceous shales, calcareous shales, impure limestones and limestones had beenintensely metamorphosed. The shales had been converted to finegrained biotite and actinolite hornfels, according to their lime content, and the impure limestones to fine-grained diopside hornfels, garnetdiopside hornfels and garnet hornfels (calc-flint), the garnet being the lime variety grossularite. The limestones, however, after being first converted to marbles, had suffered intense pyrometasomatism, involving substitution of immense quantities ,of silica and' iron for lime and carbonate, and had been converted largely to a coarsegrained garnet rock, in which the garnet was the lime-iron variety, andradite. The silica and iron were derived from the mineralising solutions of the adja,cent ,granite. intrusion, responsible for the contact metamorphism, and were accompanied by tungsten and some molybdenum. The tungsten in the presence of so much mobile lime, was precipitated as schecelite, much of it finegrained and enclosed in or intergrown, with the andradite garnet or the quartz interstitial to the garnet.It was apparent that the King Island scheelite deposit, was a perfect example of selective pyrometallomatic replacement in a bedded contact metamorphic deposit. The bedded nature of the original rocks was preserved, and the scheelite was practically limited to the original limestone beds, 'Which had been so much more susceptible to replacement after recrystallization, than the other sediments. The further geological study of the deposit then resolved itself into the task of mapping the folding and faulting of the deposit, with bore cores to provide the stratigraphic sequence, and establish the number of scheelite-bearing beds.A second example is provided by a petrological investigation of the mineral composition and genesis of the talc deposits of the Gumeracha district of South Austral.ia, which was undertaken at the request of the South Australian ,Mines Department, in conjunctionwith mapping of these deposits. The field geologist mapping the deposits was experiencing some difficulty in interpreting the structure...

Jan 1, 1950

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

One of the most important parameters in rock/resin/bolt load transfer mechanism is the surface property of the bolt. Although there are various bolt surface configurations available in the market, very little work is reported on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness conditions which is considered as being a realistic way of evaluating bolt surface roughness. A series of shear tests have been conducted on the flattened bolt surface to study the shear behaviour of bolt/resin interface. Based on the experimental results, a mathematical model has been developed to predict the shear resistance of the bolt/resin interface at various normal stress levels for the bolt types used in the study.

Jan 1, 1999

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By DiStefano AB, Dale SG

This paper describes the laboratory study implemented to investigate the application of the subaerial technique to tailings disposal for the proposed Olympic Dam Mine. The results of the study and the resulting design parameters are presented. The subaerial technique of tailings disposal is described and the advantages of the method for disposal in arid climates highlighted.

Jan 1, 1984

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014