Search Documents

By Y. F. Li

Fengning ilmenite ore is a magnetic deposit in gabbro containing high phosphorus and low titanium, the main minerals in which are ilmenite, magnetite and apatite. The dissemination size of magnetite is so fine that even the percentage of -0.010mm level is up to 36.50%. The fine and vein magnetite are distributed in gangue and ilmenite, so the majority of the magnetite is difficult to be separated from the gangue. Ilmenite is difficult to be recovered by low-intensity magnetic separation even through fine grinding. In high-intensity magnetic separation of ilmenite, the gangue inter-growth with the magnetite and the Fe-containing silicates may be enriched in the concentrate, and the ilmenite of the concentrate will be reduced. Based on the processing mineralogy research, combined gravity-flotation process is suggested to recover the ilmenite. The method is also good to reduce phosphorus in the ilmenite concentrate.

Jan 1, 2014

Investigation on Multicomponent Semi-Autogenous Grinding

Sep 13, 2010

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By M. Fig, B. Treffner, J. Brune, C. Strebinger, G. Bogin, D. Pardonner

"Methane gas explosions in a longwall coal mine can originate from in or around the gob and can seriously harm nearby workers and equipment. In order to fully understand the explosion flame and pressure wave propagation in the mine, it is important to investigate methane flame propagation in confined spaces as well as flame interaction with rock rubble and other mine structures. The latter can lead to enhanced turbulence causing high-speed deflagrations and/or detonations. Researchers ignited methane-air mixtures in horizontal, cylindrical reactors that contained inserts to simulate various gob characteristics. Rock surface topology and ignition location were investigated. Results show rock surface roughness increased fluid motion, thereby increasing methane flame front propagation velocity, overall pressure rise of the explosion, and time of pressure decay. Moving the point of ignition away from the open end of the reactor resulted in an increase in peak overpressure and an overall pressure rise of the explosion. Experiments were used to validate a computational fluid dynamics (CFD) combustion model that will be incorporated into a mine-scale explosion model to simulate and predict explosion hazards of large scale methane gas deflagrations in longwall coal mines. INTRODUCTION Coal mining is an integral part to our global society with coal-fired power plants providing about 40% of our global electricity [1]. A common method of extracting coal underground is by longwall mining. Researchers and investigative reports have found that explosive gas zones of methane-air mixtures can form along the longwall face and within the longwall gob, presenting an explosion risk to nearby workers and equipment [2]. In an explosion, the resulting flame and pressure wave presents a fatal traumatic injury hazard and can cause serious damage to equipment. In order to evaluate and mitigate the explosion risks in longwall coal mining, researchers at the Colorado School of Mines are developing a coupled CFD and combustion model of a longwall coal mine. The purpose of the model will be to better predict the explosion hazards under various mine conditions in order to build stronger prevention and mitigation strategies for miners."

Jan 1, 2018

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By Q. Zhang

Phosphate tailings through Flotation contains large amount of dolomite which is difficult to be separated from apatite. In this present research, phosphate tailings is recycled by Flotation i.e. re-processing. High-purity dolomite with purity as high as 91.17% is seperated, which contains 19.82% of MgO. The results of orthogonal test show that the effect of various levels of different factors on the high-purity dolomite floatated. Future utilization of purified dolomite is also discussed: magnesium fertiliser especially magnesium phosphate is expected to be an ideal product from high-purity dolomite.

Jan 1, 2014

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By Xiaowen Liu

The thermal decomposition of diaspore was investigated by thermogravimetry (TG),differential scanning calorimetry (DSC), X-ray power diffraction(XRD),infrared (IR)spectrain this paper. The thermal decomposition mechanism of diaspore was discussed according to Coat-Redfer equation. It was found that the decomposition of diaspore was carried out at 500?,and the peak temperature was 530?. The electrovalent balance of diaspore was destroyed. The previous crystal structure was changed. a- Al2O3 was obtained after thermal decomposition. The activation energy is 287KJ/mol.

Jan 1, 2006

By W. V. Liu, D. Omane, H. Yu, Y. Pourrahimian

"A large-scale wildfire had broken out at Fort McMurray in Alberta, Canada during May 2016. Many oil sands mining activities were affected due to the wildfire and the associated ash emissions. In particular, ash emission generated from the fire outbreak is a huge problem during the post-fire cleanup. These emissions pose a severe health hazard to workers, environment, and global climate. The ashes emitted into the atmosphere are caused by either human activities or climate conditions. The objective of this research is to assess the effect of three different ash dust suppressants, namely water, #1 surfactants, and #2 polymers at various volumetric concentrations on ashes samples to prevent propagation of fine solid emissions into the atmosphere. It is found that both #1 surfactants solution and #2 polymers solution are effective in retaining fugitive ash dust generated from the ashes. Volumetric concentration efficiency of 0.05% of #1 surfactant and 5% of #2 polymers in 500 ml of water have been proven to provide ash dust retention efficiency greater than 99% after the spraying of these suppressants. It is also found that both #1 surfactants solution and #2 polymers solution maintain an ash dust retention efficiency higher than that of the use of only water. This confirms the merit of using chemical dust suppressants on fugitive ash dust for a longer period, which is proven by the 72-hour data from this experiment. This study gives a general view of how effective chemical suppressants on fugitive ash emissions work. INTRODUCTION On May 1st, 2016, a large-scale wildfire gutted Fort McMurray, Alberta, Canada. Many oil sands mining activities were affected due to the wildfire and the associated ash emission. Due to the wildfire, some of the biggest oil sands companies in Fort McMurray such as Royal Dutch Shell and Suncor Energy shut down their oil production, at 255,000 and 350,000 barrels per day respectively [1]. Syncrude Canada Ltd scaled down its normal production capacity level of 350,000 barrels per day [1]. This generated an estimated loss of about 1.1 million barrels of oil production per day, constituting a 30% reduction in the Canadian daily oil production, crippling the economy [2]. This loss in production by the companies translated into 0.33 % of the Alberta GDP in 2016 constituting a loss of $985 million and 0.06 % of the entire Canadian economy [3]. In 2017, it is estimated that the rebuilding and reclamation of the affected areas in Fort McMurray will add $ 1.3 billion in GDP to Alberta’s economy [3]. A population of over 90,000 people was evacuated from the location and its surroundings for health and safety reasons [4]. The fire destroyed about 2,400 structures and over 500,000 hectares of forest vegetation in Fort McMurray, leaving an estimated 232,000 tonne of post-fire ashes [5,6]."

Jan 1, 2017

Chief Geologist, Groundwater and Engineering Geology Branch South Australian Department of Mines and Energy The six papers submitted for consideration during this session include two dealing with techniques for measing rock mass behaviour, including permeability, in boreholes, one describing the use of surface geophysical methods to delineate pollution plumes in groundwater together with analytical modelling of the plume, and one presenting a biological tracer technique applied to the determination of the origin of water entering underground mine workings. A paper describing dewatering at a base metal mine in Queensland includes an account of the investigation techniques employed to establish a conceptual model as a basis for the evaluation of various dewatering strategies. Of considerable interest is the use of a field gravity survey to delineate a zone of highly weathered rock which forms the major aquifer at the site.

Jan 1, 1988

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By R. Franfield, W. J. Birch, L. Bermingham

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as consequence of the shock wave created by the detention of the explosive charge in a blast hole, rapidly propagating through the rock and then impacting on the quarry face.

Jan 1, 2013