Search Documents

By I. E. Campbell, R. I. Jaffe

Oxygen, nitrogen, and hydrogen are known to be absorbed by titanium at elevated temperatures. Ehrlichl reports that about 30 at. pct oxygen can be dissolved in solid solution by alpha-titanium. Nitrogen also has a solid solubility in alpha-titanium, but there is no information as to its extent. The solid solubility of hydrogen in titanium also is high. Kirshfeld and Sieverts2 report 50 at. pct soluble, while Hägg3 reports about 33 at. pct hydrogen to be soluble in alpha-titanium. General statements are made in the literature that oxygen, nitrogen, and hydrogen embrittle titanium, but no quantitative measurements have been made of the effect of these gases on the mechanical properties of the metal. One reason for this is the lack of a source of titanium pure enough to be considered a suitable starting material. Iodide-refined titanium, made by thermal decomposition of titanium iodide vapor on an incandescent wire,4 contains small amounts of carbon, silicon, iron, and aluminum, but is very low in oxygen, nitrogen, and hydrogen content, and, therefore, was used in this work. A further reason for the lack of quantitative information on the effect of these gases, particularly oxygen, is the difficulty of carrying out accurate analytical determinations at the low concentrations of interest in this work. For this reason, the oxygen, nitrogen, and hydrogen were added in measured amounts as gases, and diffused into the titanium, to avoid the necessity of chemical analysis. The purpose of the work reported here was to isolate and measure the effects of oxygen, nitrogen, and hydrogen on titanium of the highest purity available at the time. The concentrations studied were 0.25, 0.5, and 1 at. pct in each case. Experimental Work One-half of a 24-in. hairpin of iodide-refined titanium was available for this work. The rod was approximately 0.25-in. in diam and had a 0.003-in.tung sten core. From chemical and spectro-graphic analyses, the purity of the sample was estimated to be between 99.80 and 99.95 wt pct. The chief impurities (aside from the tungsten core) were iron (0.04 pct), silicon (0.01-0.1 pct), aluminum (0.05 pct), carbon (0.03 pct). The tungsten core constituted 0.05 pct by weight of the sample. Although some alloying undoubtedly took place between the tungsten and the titanium during the deposition reaction, the core remained substantially intact in the deposited metal. The initial average hardness of the titanium as deposited was 105 Vickers (10-kg load). The maximum hardness was 116 Vickers and the minimum 91 Vickers. The metal was somewhat harder than that currently being obtained by the iodide process, that is, 75-90 Vickers. The rod was cold swaged to ¼-in. diam and then cold rolled in diamond shaped rolls to about 0.080-in. square, using reductions of 15 pct in area per pass. The 0.080-in.-square wire was cut into 6-in. lengths for the preparation of the alloys by the gaseous absorption and diffusion method. ADDITION OF OXYGEN, NITROGEN, AND HYDROGEN TO TITANIUM A modified Sieverts' absorption apparatus, shown in Fig 1, was used in

Jan 1, 1950

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By J. T. McGrath, G. B. Craig

Tensile tests on aluminum single crystals, grown from the melt, revealed that the yield stress of these crystals was raised as the amount of striation substructure was increased. The number of striation-type boundaries was varied by changing the rate of growth of the crystals. The results are interpreted in terns of a blockage of dislocation movement by striation boundaries. IMPERFECTIONS are known to have a large effect on the mechanical properties of metals. Teghtsoonian and Chalmers 1 studied a block or striation-type substructure in tin and found that the formation of the striations depended upon rate of crystal growth and orientation. They found that the angular misorienta-tion between neighboring striations varied between 15 min and 5 deg. Atwater and chalmers2 investigated striations in tin and lead, and found that purity was another factor which influenced their formation. There was a limiting purity above which the striations were straight and regular. There is little information in the literature concerning how substructures in melt-grown crystals affect strength. washburn3 introduced small-angle boundaries into zinc by a shear process and found a subsequent increase in yield stress which he attributed to the presence of these boundaries. Lauriente and pond4 found the critical resolved shear stress in aluminium crystals grown from the melt, to increase with etch pit density. The etch pits were used as an indication of growth imperfections. In Hibbard's5 work on lineage structure in copper crystals grown from the melt, he tested one crystal containing interlineage boundaries, and found a 50 pct increase in the critical resolved shear stress. Fleischer and Chalmers6, in a recent paper, mention briefly that, in the production of aluminium crystals from the melt when the growth rate was raised from 1.2 to 18 cm per hr, the yield stress increased 50 pct. They felt that the increase in yield stress with rate of growth might be attributed to a higher concentration of impurities in the gage length and also might be affected by the increased number of small-angle boundaries (striations). The present investigation was undertaken to determine the effect of the striation substructure on the strength of aluminum single crystals. EXPERIMENTAL PROCEDURE Aluminum single crystals of 99.9992 purity were grown from the melt using a technique described by Chalmers.7 The growth rate was varied from 0.6 to 20 mm per min, thus producing crystals with varying numbers of striation boundaries. To avoid prior deformation, the crystals were chemically cut to the desired length with a saturated solution of cupric chloride. They were then annealed at 580°C for 24 hr and allowed to cool slowly in the furnace. Finally, the specimens were electropolished using an electrolyte of 5 parts ethyl alcohol and 1 part perchloric acid. Each specimen was approximately 5 in. in length and 0.125 sq in. in cross section. The average orientations of the 5 series of crystals studied are shown on the stereographic projection of Fig. 1. The crystals were strained approximately 2 pct in a soft tensile machine. The strain sensitivity was 3.6 x 10-4 cm over a 5-cm gage length.

Jan 1, 1960

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By I. R. Kramer, L. J. Demer

Aluminum single crystals were pulled in an electrolytic cell allowing surface removal during the deformation. The extent of Stages I and 11 of the stress-st-aitz curve was increased and the slope decreased as the rate of metal removed from the surface was increased. An increase of the strain rate caused a decrease in the effectiveness of the metal removal. The data indicate that the work-hardening coefficient in Stage I is determined primarily by the conditions which exist on the surface of the crystal. In Stages 11 and 111, both surface effects and internal barriers are important. ALTHOUGH numerous investigations have been conducted on the plastic flow characteristics of metals in an attempt to explain the mechanism of work-hardening, relatively few studies have taken into account the influence of the surface. In all current theories of work-hardening it is assumed that the impediments to the movement of dislocations are within the crystal. The barriers due to the surface and the existence of solid and liquid films have been neglected even though it has been demonstrated that the surface exerts a large effect. A number of investigators1-l8 have shown that solid films on the surface of single crystals markedly affect their mechanical behavior. In general, the presence of a solid film tends to increase the yield stress and increase the work-hardening rate. Often, on single crystals, Stage I and, at times, Stage II regions are completely suppressed. Various mechanisms have been offered for the effects of oxide and metal films as well as the influence of electrolytes. Of these, concepts concerned with the locking of surface dislocation sources and the blocking of dislocations at the surface resulting in pileups appear to be actively considered at present. Barrett,11 Takamura,6 Gilman,19 Lipsett and King,20 Shapiro and Read,10 and Weiner and Gensamer21 are among those who have interpreted their results in terms of piled-up dislocations at the surface, while Adams.22 and Chalmers and Davis23 have explained their experimental observations in terms of locking of surface dislocation sources. In general, the change in plastic flow properties due to electrolytes has been explained in terms of the unblocking or unlocking of dislocations by the removal of the oxide films. In considering the two proposed mechanisms, it appears that the locking of sources of surface dislocations by a solid film should exert a primary influence only on the critical resolved shear stress for flow and not on the slopes of Stages I and 11. However, the blocking at the surface of dislocations from internal sources may also affect the critical resolved stress and furthermore exert an influence throughout the whole plastic range. In certain cases it does not seem feasible to explain the results of experimental observations in terms of locking of surface dislocation sources. The abnormal aftereffects found by Barrettll,12 by removing the oxide by an acid treatment are excellent evidence of the blocking of dislocations at the surface. Additional evidence in favor of a blocking due to a pileup of dislocations at the surface may be found from the observations that the critical resolved shear strength continues to increase with the thickness of the oxide layer until very heavy oxide layers are formed. If the locking of surface dislocations sources were the dominant factor, the critical resolved shear stress would not be expected to increase after all of the surface sources were locked by the formation of the oxide. This may be expected to happen after a few atomic layers of the oxide are formed. In spite of the above evidence on the strong influence of the surface on the plastic flow characteristic, this has been ignored in current theories of work-hardening. Seeger24,25 suggested that most of the dislocations may slip out of the crystal only when the specimen axis is within certain areas of the orientation triangle. In other areas the resolved shear stress in other glide systems is large enough to generate dislocations which can form Lomer-Cottrell locks, thereby decreasing the average slip distance in some directions and causing a larger hardening rate. Friede126 assumed that at the beginning of Stage 11, a large number of Lomer-Cottrell dislocations are formed by a catastrophic process which used up all the Frank-Read sources on the secondary slip-planes. In this manner a fixed number of Lomer-Cottrell locks is formed which act as barriers against which the dislocations can pile up. In Stage 111, Seeger24 and Diehl, Mader, and Seeger25 proposed that Lomer-Cottrell barriers are circumvented by the cross slip of extended screw dislocations. Cottrell and Stokes,27 Friedel,26 Cottrell,26 and stroh29 suggest that the Lomer-Cottrell dislocations collapse under the stress field of the dislocation pileup. It is the purpose of this paper to report the changes in Stages I, II,and III of the deformation process in

Jan 1, 1962

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By I. R. Kramer

Single crystals of aluminum were pulled in tension in a solution of paraffin oil and stearic acid. The critical resolved shear stress did not change with the concentration of the stearic acid solution; however, the extents and slopes of Stages I and II were affected greatly. The observations lend evidence that the weakening effect of surface-active agents is controlled by the rate of desorption of the metal soap formed by the reaction of the surface-active agent and the metal surface. IT has been shown by various investigators1-" that surface-active agents markedly affect the mechanical properties of single crystals. (A surface-active agent, for the purpose of this report, is defined as a long-chain organic molecule which contains one or more polar groups. Usually, however, investigations have considered only molecules having one polar group.) In general, when single crystals are deformed in some solutions containing surface-active agents, the creep rate, Fig. 1, is increased and the yield strength is decreased. The fatigue strength has been reported to be affected also.ll Rehbinder and his asociatesl' explained the "weakening" effect of surface-active agents in terms of physical adsorption. They assumed that a large pressure was created in microcracks which existed on the surface of the crystal." Harper and Cottrell,' from their study of the effects of surface conditions, found that the deformation characteristics of zinc single crystals were not altered by a solution containing a surface-active agent unless the surface of the specimen had an oxidized surface. They concluded that the role of the polar molecule was to remove the strengthening effect of the oxide coating. Later, And-radeetBpresented additional evidence which appeared to agree with this conclusion. In contrast, Klinken-berg et al.7 reported data which confirmed the results of Rehbinder. Using zinc and cadmium crystals which had been cleaned by electrolytic polishing, a large increase in the creep rate was observed when Lle specimens were tested in a 1 pct oleic acid-paraffin oil solution. They also reported that the creep rate

Jan 1, 1962

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By E. C. Rudolphy, M. E. Potter, J. R. Mitchell

The effects of 0.006 to 0.20 pet Sn ml the hot workability and the annealed mechanical properties were investigated for Types 302, 410, and 430 stainless steel. The hot workability of these steels was not significantly affected by their tin content within the range studied, although some effects on mechanical properties were noted. Apart from the effect of tin, optimum hot-working temperatures and V-notch Charpy impact transition temperatures for these grades were determined. HIGH tin residuals in some heats of stainless steel have been blamed for the poor hot workability, particularly during secondary mill rolling. However, very little quantitative information has been available. Previous work1"6 with carbon steels indicates that tin increases tensile strength and hardness but de- creases tensile and impact ductility. Halley,7 in reviewing the sources and effects of residual elements in carbon and alloy steels, concluded that much of the surface checking (hot shortness) encountered in rolling was caused by copper, and that tin, arsenic, and antimony combined with copper to form low-melting constituents which further increase the steel&apos;s sensitivity to hot shortness. These elements had little effect in the absence of copper. A more recent paper by Langenberg and Johnson8 concluded that tin reduces hot workability but that researchers disagree concerning the amounts which will cause trouble. They state that laboratory investigations with small ingots seem to indicate a higher tolerable level of tin than do statistical studies of mill data, and also that statistical analysis of mill data indicate that small amounts of residual tin are detrimental to the surface quality of stainless sheet. The accumulative increase in the general level of tin and other tramp elements in steelmaking materials will present greater problems to steelmakers in the future. The purpose of the present study was to obtain quantitative information on the specific effects of tin on the hot workability and mechanical properties of such common stainless steels as Types 302, 410, and 430.

Jan 1, 1962

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux&apos; reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann&apos; and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;&apos;-&apos; of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By J. B. Coher, M. B. Bever

COLD work destroys long-range order, as was first observed by Dehlinger and Graf.1 Dahl2 showed that the mechanical disordering caused by cold work produces changes in those properties that are affected by long-range order. The existence of order has a marked effect on tile manner in which an alloy deforms and therefore on its mechanical properties.L&apos; The relation between order and deformation behavior however, is only beginning to be understood. Seemann and G1ander4 suggested that cold work reduces an ordered alloy to a kind of gruel of antiphase domains. According to Cottrell,5 superdis-locations and pairs of dislocations in a slip plane connected by a strip of anti-phase domain boundary provide deformation mechanisms which do not change the state of order. In general, however, slip may be expected to produce new domain boundaries and destroy order if dislocations move on intersecting planes or cut through existing domain boundaries. The yield strength of an ordered alloy may pass through a maximum with decreasing domain size.5"7 The reduction of domain size resulting from cold work may, therefore, lead to a maximum in strength properties. Flinn8 suggests that dislocations can climb by short-range diffusion during deformation and thus can generate domain boundaries not only on slip planes, but also on other planes which will be those with the lowest domain-boundary energy. It has long been known that the rate of strain hardening of an alloy in the ordered state is larger than in the disordered state.3&apos;9 Also the slip bands in ordered CU3, AU10 and Ni3Mn" are finer than in the disordered alloys. The stress which causes initial yielding in Cu,Au passes through a maximum with decreasing domain size.6&apos;12 A maximum has also been observed in the hardness of ordered Ni3Mn as a function of strain.&apos; These observations suggest, but do not prove, that domain size reduction occurs during deformation. According to Fisher13 slip destroys short-range order and thus the strength of an alloy is related to the degree of short-range order present. Rudman and Averbach14 and Averbach et a1.,15 demonstrated that cold work reduces short-range order in copper-gold and gold-silver alloys. Destruction of long-range and short-range order by cold work implies slip on an appreciable fraction of planes. Yielding of an alloy in which short-range order exists or antiphase domain boundaries are present should be discontinuous because the first dislocations moving across the slip plane meet with the largest resistance.5 Such discontinuous yielding has been observed in CU3AU6,16 and Cuzn.l7 This phenomenon, however, can also be explained by mechanisms not involving order.b The published investigations of the effects of cold work on alloys with long-range or short-range order have not been covered thoroughly in reviews of order-disorder phenomena. These investigations, therefore, will be listed here. They have been concerned with strength properties> 2,3,6,8,9,12,16-21 electrical resistivity,2,4,18,19,21-26: thermoelectric power, magnetic properties,2,18,21,26 and X-ray strain&apos;1,2,14,15,27,28 The slip systems and the appearance of the microstructure after deformation in ordered and disordered alloys have also been investigated. 6.10.ll,l7,23,29,30 The alloys used in these investigations were copper-gold. 1-4,6,9,10,14,16,18 23-26,28,29 copper-zinc. L7. 19. 20,30 nickel-manganese,2 11,21 iron-aluminum. iron-nickel,&apos; copper palladium,4,18,22 gold-silver.4,18,22 and palladium-silver-copper.4 In the work reported here. the changes in properties of polycrystalline Cu3Au were investigated as functions of strain in wire drawing and rolling. Specimens were heat treated before deformation

Jan 1, 1961

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.&apos; This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2&apos;6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7&apos;9 These effects were observed at testing temperatures in the range 100 to 300&apos;. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.&apos; These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180&apos; was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio &apos;c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By F. Seitz

STAFF: Editor, Gerhard Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Managing Editor, James J. Burke THE METALLURGICAL SOCIETY: John Chipman, President; W. R. Hibbard, Jr., Post-President; C. C. Long, Vice-President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. Maddin, Chairman; Dennis Carney, J. C. Fulton, J. H. Hollomon, T. B. King, C. C. Long, W. 0. Philbrook, J. D. Sullivan, David Swan, and F.L. Vogel. Review and selection of manuscripts is under the supervisian of the following Publications Committees: Extractive Metallurgy D ivis ion: T. 0. King, Chairman; S. J. Dick inson, R. P. Hermsdorf, R. Schuhmann, Jr., and H. H. Kel logg. Institute of Metals Division: F. L. Vogel, Choirmon; R. L. Smith, Vice Chairman; R.W. Balluffi, J. H. Bachtold, A Servi, C.D.Graham, Jr., C. G. Goetzel, F. E. Joumot, Jr., G. E. Pellissier, Paul Gordon, Jock Washburn, Harold Margol in, A. U. Seybolt, I. R. Kromer, R. A. Meussner, R. W. Guard, M. Harmon, J. N. Hobstetter, Dean Starr, P. Shewmon, R. Gordon, J. 0. Betterton, and E. Morgan. Iron and Steel Division: W. 0. Philbrook, Chairman; F. C. Langenberg, C. W. Sherman, J. Wagstaff, and E. J. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1959 by the Americon Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . .Second class postage paid at New York, N. Y. , ond Ann Arbor, Mich. Volume 215, Number 3

Jan 1, 1960

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs&apos;tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960