Search Documents

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012

By A. Angelov, U. Peukerd, S. Gaydardzhieve, A. Stefanov, K. Grossman, V. Stoilov

Flotation concentrate originating from the Asarel-Medet porphyry copper mining and processing complex in Bulgaria has been subjected to regrinding using a Ro-Star mill; the effects of which on the downstream metallurgical behaviour are discussed. Particularly the effect on the liberation degree was studied through an optical microscopy and MLA-SEM automated mineralogy. On the other hand, copper selective flotation of the reground bulk concentrate was realised to evaluate the anticipated metallurgical improvement. Process parameters such as involvement of prior hydrocycloning and variation of collector dosage have been evaluated. Within a two-minute residence time inside the Ro-Star mill, an improved liberation degree of the copper bearing minerals has been observed. As a consequence, enhanced copper recovery and selectivity against pyrite was noted. It has been found that in order to guarantee efficient flotation of the resulting ultrafine particles, a modified flotation regime (i.e. changing collector suite and dosages) should be followed. Keywords: RoStar Mill, liberation, flotation recovery, ultrafine particles

Jan 1, 2020

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By Robert Lamarre

In today?s environment, the availability of production equipment is a must to increase throughput and profits. For a number of mining organizations around the world, spare parts availability is key to achieving this goal. Fortunately, having less production equipment immobilized by a lack of spare parts does not equate to increases in inventory levels or in carrying costs. Advance operations research has shown a number of avenues to increase equipment availability while reducing total investment in stock. The presentation will explore these avenues by focusing on key inventory management changes that can be implemented by organizations to optimize their service and stocking levels. We have successfully applied our approaches in start-up mining projects, in mature projects and in end of life mining operations. We will illustrate our methodology using examples from our work with > 30 mining sites around the world.

Aug 1, 2013

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980's by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By Pekka Taskinen

Advanced optimizing control of the fluidised bed zinc roaster has been in use for an extended period at Boliden Kokkola and the implications are seen as extended bed stability, increased throughput and far better on-line availability. The roaster furnace control system developed is based on a dynamic and predictive furnace model, with parameters determined experimentally at the site. The controller maximises the concentrate feed and keeps the furnace operational parameters inside limits given by raw material mix and equipment constraints. The products of a zinc roaster, calcine, sulphur dioxide and the side products, such as mercury, meet gradually more stringent requirements, in particular as to their assays and total recoveries in the process chain. The end users of sulphuric acid in northern Europe, among others in the pulp and paper industry, require mercury levels much less than the conventional 0.2-0.4 ppm Hg. Therefore, secondary de-mercurising circuits have been used over the last five years for further cleaning the SO2 stream allowing production acid grades with less than 0.08 ppm Hg.

Jan 1, 2008

By Edward C. Mabbs

U.S. industry must increase its productivity or lose its competitive position in the rapidly expanding and inter-dependent world markets. Recent improvements in material handling techniques and equipment, coordinated with production processes, provide one of the greatest opportunities to increase productivity. Successful managers must learn how to take advantage of these material handling opportunities to gain competitive position.

Jan 1, 1973

By A Clark

When production targets are not being reached it is essential to determine what the operating problems are so that remedial action can be taken. It is also imperative that all persons who are part of the production stream within a mining operation know and understand what the operating difficulties and delays are so that corrective action is effective. This includes the supervisors, superintendents, planning team members and managers. A new approach recently adopted at Hilton Mine to help identify these operating difficulties has been to use short-term schedules and reports known as the Daily Shift Schedule Controls (DSSC), and the Daily Weekly Operating Reports (DWOR) respectively. These control elements have enabled management and supervisory staff to accurately identify labour inefficiencies and ultimately determine capital resources.

Jan 1, 1998

By J. C. Adams

Although explosives constitute only a small portion of a mine's total cost, the relative success of each blast has a tremendous effect on subsequent activities such as excavation, crushing, and equipment maintenance. Beginning in January of 1993, tests were carried out to determine whether productivity could be improved by replacing standard ammonium nitrate fuel oil mixtures (ANFO) with a high density, high performance blasting agent. The study was carried out at gold mines, coal mines, and cement quarries in Nevada, California, Colorado, and New Mexico. A wide variety of rock types and blasting conditions were encountered. Results showed that at most operations productivity was sufficiently improved to more than offset the increase in explosives cost. This resulted in a net reduction in mining cost. This paper presents a summary of these results.

Jan 1, 1996

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988