Search Documents

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

By Ashwani Jain, D K. Soni

Compressive strength of rocks is often required by mining engineers and quarrying authorities for blasting operations. Uniaxial compressive strength of rocks can be predicted with reasonable accuracy with the help of point load strength tests which can be easily conducted at site by the field staff, simultaneously as the cores are recovered from drilling operations. A number of diametral point load tests and uniaxial compressive strength tests have been conducted on the specimens of different rock types under air dried, and saturated condition as well to study the effect of ground water saturation on strength. It has been observed that due to saturation uniaxial compressive strength and point load strength get reduced to a maximum of 32 and 29 per cent respectively. It has also been observed that uniaxial strength is sixteen times the point load strength in air dried as well as saturated condition. However, this factor used for calculating uniaxial compressive strength may be reduced to a lower value for the safety of miners in field blasting operations.

Jan 1, 1994

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By M. Liu

In-situ soil washing using surfactants shows great potential to remove hydrophobic organics from subsurface environment. Lab scale soil washing experiment were performed using Sodium Dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that solubility of anthracene increases linearly with an increase in SDS concentration above the critical micelle concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1992

By Lane D. Schultz, John D. McLennan, Jean-Claude Roegiers

During construction of the intake tunnels for a nuclear power facility in Ohio, evidence of a potential geological discontinuity was discovered. Assuming that the discontinuity might still prevail underneath the site, it was decided to measure the stress profile across the discontinuity. This information would be used to assess future stability on the basis of predicted shear stresses acting along the fracture. Seven intervals were hydraulically fractured to determine the magnitude and orientation of the stress tensor, in order to infer the shear stresses acting along the discontinuity. The formation consists of tightly interbedded shales. This, in combination with the shallow depths, would be expected to lead to horizontal hydraulic fractures -- a situation which generally provides limited information. Careful testing procedures, and meticulous interpretation, allowed the determination of the horizontal stress components as well as the vertical component, via the initiation and/or propagation of multiple fractures. The measured stresses fall within the range of stress magnitudes and orientation determined in other areas of the northeastern and north-central United States and in southern parts of Canada. In addition, a small stress gradient anomaly was recorded at depth. On a different scale, the measured stress regime is also evaluated in light of the regional geological setting.

Jan 1, 1982

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By S. O. Choi, C. Park, C. Sunwoo

Two methods of stress measurements have been executed on the surface and underground to con-struct an oil storage cavern using hydro-fracturing and overcoring method. The first measurement has been performed to make a design of the caverns before excavating and the second to confirm the stress state during excavation. Six measurements have been carried out in the hydro-fracturing test at the depths between –17.8 and 54.5m from the sea level and a single measurement in the overcoring test in a single borehole at the depth of –21m from the sea level. The ratios of the maximum horizontal to vertical stress measured using hydro-fracturing and overcoring method are 2.95 and 3.1, respectively. Also, the orientations of the maximum horizontal stress are N53E and N58E. These measurements show that both methods give almost same results and significant horizontal stresses are acting on this cavern. Deux méthodes de mesure de contrainte ont étè exécutées sur la surface de terrain et sous la terre pour construire une cavité de stockage de pétrole en utilisant l’hydro-fracturing et l’overcoring. La première mesure a étè faite pour le plan des cavités avant l’excavation et le seconde pour con-firmer l’état de contrainte durant l’excavation. Six measures ont étè faites dans le teste de l’hydro-fracturing à la profondeur entre –17.8 et 54.5m depuis l’élèvation maritime. Une seule mesure a étè faite dans le teste de l’overcoring dans une seule trou de songdage à la profondeur de –21m. Le ratios de la maximale contrainte horizontale à la contrainte verticale mesure par les deux méthodes sont 2.95 et 3.1, respectivement. Les orientations de la maximale contrainte horizontale sont N53E et N58E. Ce montre que les deux méthodes donnent presque m me résultats et la contrainte im-portante est activée sur ces cavités. Zwei Druckmessungen wurden durchgeführt auf der Erdoberfläche und im Innern von Ölspeicher-kavernen unter vergleichender Anwendung des Hydrofraktionierungs- und des Kernbohrungsver-fahrens. Die erste Messung wurde durchgeführt um einen Plan der Kavernen vor der Herstellung zu erstellen und die zweite um die Druckverhältnisse während der Bohrung zu überprüfen. Sechs Messugnen wurden mit der Hydrofraktionierungsmethode bei einer Tiefe von 17,8m und 54,5m unter dem Meeresspiegel und eine einzige Messung mit der Kernbohrungsmethode in einem Bohr-loch bei einer Tiefe von 21m unter dem Meeresspiegel vorgenommen. Das Verhältnis von maxi-malem horizontalem zu vertikalem Druck bei der Hydrofraktions- und der Kernbohrungsmedthode ist 2,95 bzw. 3,1. Die Bezugspunkte des maximalen horizontalen Drucks in beiden Verfahren sind N53E und N58E.

Jan 1, 2003

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

To produce high quality castings, one must monitor the melt quality by evaluating such parameters as the grain refinement and silicon inoculation and modification during the production of the commercial casting. Thermal analysis is a tool one can use for both monitoring and providing input to the process control of the operation. The current technique of performing thermal analysis in commercial foundries is to pour a relatively small quantity of the molten aluminum alloy into a sampling cup and to then acquire the cooling curve. This approach is somewhat simplistic in that one has limited control of the cooling rate and hence the solidification rate of the sample. Moreover, this process requires a fair amount of user intervention and effort. In the past, studies have been conducted in an attempt to develop a system for conducting thermal analysis in-situ. In a study at McGill University, an alkali based heat pipe system was developed for conducting thermal analysis in-situ. While the concept was deemed as very desirable, the complexity of the equipment and procedure was a substantial negative component. In order to improve the technique of accomplishing real-time thermal analysis with an in-situ probe, a new method that is based on McGill heat pipe technology was developed. In the new system, a controllable and flexible water based heat pipe probe is used to solidify a small quantity of metal while residing in the melt. The solidified aluminum is remelted after completing the thermal analysis. This is a key feature of the probe. It resides permanently in the melt yet it is able to both solidify a sample of the melt and then to subsequently remelt it. Various solidification rates encountered in commercial castings are attainable by adjusting the heat extraction rate of the unit.

Jan 1, 2004

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By L. M. Litz

The results of a study are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 parts per million. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that were concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1980

By Hong Peng, James Vaughan

Thermal activation of bauxite has been proposed to enable bauxite dissolution at a reduced digestion temperature and also to reduce the organic content in the liquor. Research has been carried out on phase transformation of its main hydroxide components (gibbsite, boehmite and kaolinite) during calcination. However, there is limited information available on phase bauxite phase transformation during thermal activation. In this study, two bauxite ore samples were heated from 25 to 700 °C at a rate of 50 °C/min while monitoring the phase transformation using Rigaku in situ XRD. Different phase transformation pathways for gibbsite in the bauxite compared with pure gibbsite was observed. Boehmite and kaolinite in bauxite behaved similarly to their pure phases. The temperature of phase transformation depends to some extent on the bauxite sample. Samples were also characterised by scanning electron microscopy (SEM) to reveal changes in the microstructure.

Mar 1, 2018

By G. Brooker

The back-filling operation at Olympic Dam mine supports a 9.8 million tonne per year (Mtla) underground Longhole Open Stoping operation. It involves a combination of Cemented Aggregate Fill (CAF), Surface Rockfill and Underground Rockfill. The fill material is introduced from the surface via bore-holes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process. The need for a means to measure the filling process is driven by the stopes, which have both rock and CAF fill placed in them. The large volumes and high relative cost of CAF makes the minimization of CAF fill a business priority. Incorrect filling can lead to the sterilization of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill control device. This paper reviews the salient points of the technology and its potential use in the back-filling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by 'seeing' through water and dust laden environments such as that found in stopes and ore passes is discussed.

Jan 1, 2001

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By Errol Ladner

The application of large-diameter bore holes in underground operations at Heath Steele was first tried in February, 1975. Since that time, 90,000 feet of 6-l/2-inch holes have been drilled, primarily in open blasthole stoping, for a total of 1.4 million tons, 37% of underground production. This paper deals with a review of drilling with conventional percussion longhole drills, a practice which is still utilized at Heath Steele, and the changeover to accommodate the use of larger blastholes in underground operations. The discussion will include layouts for 2-inch-diameter blasthole stope blocks, 6-inch-diameter stope blocks, trials for I. T.H. (in-the-hole) stope rooms, and drill pat/ems, drilling and performance. The complexity involved in the development, drilling and blasting of 2-inch blastholes is overcome by the over-all simplicity of drilling and blasting in I. T.H. stopes. This has made the practice of open blasthole stoping more economical and efficient. The future indicates an increase in the company's I. T.H. program. Investigations are being undertaken regarding longer holes to decrease development costs. A VCR stope is also being developed for trial.

Jan 1, 1979