Search Documents

By J M. Nel

Richards Bay Minerals (RBM) has recently undertaken an exercise to improve orebody basal definition. Older mineralisation bases (pre-2005) were highly erratic using old protocol reverse circulation (RC) (also known as Air Core) drilling and interpretation. The erratic nature of this estimation tool, resulted in impractical modelling towards the end of mineralisation (EOM), difficult mine design and unrealistic reconciliation. New protocol drilling, which includes high definition SONIC drilling data, has provided more data to be available for more accurate interpretation. Recent advances in drilling methodology has allowed for better penetration depths for SONIC drilling, which was previously restricted to approximately 80 m (pre-2005). This improved data set allows more emphasis on geological interpretation with factors such as lithology, slime content, and mineral species distribution. These factors when in unique combination enable more accurate and realistic EOM data points. These points are modelled into surfaces using conditional simulation techniques and result in a vastly smoother surface and consequently, a more representative resource.

Oct 5, 2011

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By Michael Kynett, Francke Walberg, Richard Millet, Khaled Chowdhury, Mary Perlea

"Cutoff walls are the most common seepage improvement measure for levee flood control projects throughout California’s Central Valley. Cutoff walls are widely used because they can be implemented within an existing right of way in either heavily urbanized areas with limited access, or in high-value crop agricultural areas. The most commonly used seepage cutoff wall types are soil-bentonite (SB), soilcement- bentonite (SCB), and cement-bentonite (CB). Contract values for cutoff wall rehabilitation projects in the Central Valley range from several millions of dollars to hundreds of millions of dollars, and play a significant role in the reduction of flood risk in urban and rural areas. However, recentlycompleted construction of several levee improvement projects has shown limitations and inconsistencies among the commonly used technical specifications for construction of seepage cutoff walls. These limitations were evaluated by practicing engineers involved in different stages of cutoff wall design and construction. This paper describes the specification areas that typically generate design and construction issues. Recommended improvements to specifications are suggested to address these issues. The paper’s topics include: the applicability of the different types of cutoff wall materials and construction methods, quality control testing requirements, backfill gradation requirements, mixing procedures, and settlement criteria for backfill.INTRODUCTIONFlood control projects on the Sacramento and San Joaquin rivers in the Central Valley region of Northern California consist of a large system of reservoirs, bypasses, and levees. The thousands of miles of levees within the system were largely constructed and raised by local entities as need arose; this construction occurred prior to the development of modern design and construction techniques. The majority of these levees were initially constructed to protect land for agricultural development; however, a significant portion of these areas have become or will soon be urbanized. This urbanization has historically occurred in locations right up to the levee footprint. This expedient form of historical levee construction, when combined with adverse riverine geomorphology, urban development, and productive agricultural regions, has led to a levee systems with severe seepage performance issues in a real-estate-constrained setting."

Jan 1, 2015

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By Greg M. Hollyer

The search for minerals in the future will be dominated by deeper exploration and the need to accurately target ?blind? deposits as more and more of the ?easy? near surface targets are exhausted. In this context, key technologies are emerging for deep exploration both in grassroots and minesite exploration, including the Titan 24 Deep Penetrating geophysical technology. Introduced in 2001, this technology has grown rapidly into an accepted approach for exploration in a variety of geologic environments, including brownfield environments where discovering additional reserves would most quickly benefit companies. Titan 24 belongs to a new class of sophisticated Distributed Acquisition Systems (DAS) which record high-volume, high-quality data simultaneously at multiple receiver stations. This data is then processed digitally, modeled using specialized inverse modeling software, and interpreted according to geologic and other parameters. The result is a robust, high-quality, high-volume data sets which provide a basis for improved imaging to depth. In this paper, the Titan 24 distributed technology is discussed. Illustrations of the vast improvement to overall exploration are showcased through results in several case studies. These include examples from two gold deposits, a porphyry deposit and a minesite. These examples show the range of applicability of the technology and the ability to effectively image mineralization, lithology, structure and alteration to depth as an aid to understanding prospective mineral deposits and targeting drills more accurately.

May 1, 2008

By E. Goris Cervantes

"A theoretical framework based on a detailed analysis of mine operations data from an oil sands mine in northern Alberta and the static simulation of truck cycle times are developed, verified, and validated in this paper. Implementation of this framework provides better results than existing tools that rely solely on manufacturer data. This, therefore, aids in efficient equipment planning for the life of the mine. The use of this framework to modify existing productivity curve estimation methods currently in use at the mine site is also proposed. This method replaces “loaded flat haul” with “loaded effective flat haul” in the productivity estimation. Validation of the model results in a 4% overestimation of productivity, versus an underestimation of more than 10% when using the existing in-house method. ¦ KEYWORDS Equipment planning, Life-of-mine (LOM) planning, Oil sands, Productivity, Truck cycle times RÉSUMÉ Un cadre théorique fondé sur une analyse détaillée des données relatives aux activités minières d’une exploitation de sables bitumineux dans le nord de l’Alberta et la simulation statique des temps de cycle des camions sont développés, vérifiés et validés dans cet article. La mise en oeuvre de ce cadre offre de meilleurs résultats que ce que proposent les outils existants, lesquels se basent uniquement sur des données des constructeurs. Ceci contribue donc à une planification efficace de l’équipement pour des projets relatifs à la durée de vie de la mine. On propose également de se servir de ce cadre pour modifier les méthodes d’estimation de la courbe de productivité actuellement utilisées sur le site minier. Cette méthode remplace le concept de loaded flat haul (la distance parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) par celui d’effective loaded flat haul (la distance relative parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) dans l’estimation de la production. La validation du modèle résulte en une surestimation de 4 % de la productivité, par rapport à une sous-estimation de plus de 10 % avec la méthode actuellement utilisée en interne. ¦ MOTS CLÉS planification de la durée de vie de la mine, planification de l’équipement, productivité, sables bitumineux, temps de cycle d’un camionINTRODUCTION One aspect that differentiates oil sands mines in northern Alberta from conventional hard-rock mining is the environment in which they operate. Due to ground characteristics, producers in the region experience roads with very high rolling resistance (RR) that, in turn, negatively affect haul-truck performance and greatly increase fuel consumption and emissions. Oil sands mining companies use some of the largest haul trucks in the world. In addition, oil sands mines cover more extensive areas than hard-rock pits, resulting in longer haul distances on roads made of comparatively more viscous material."

Jan 1, 2019

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Tomoya Kawasaki, Tatsuya Motomura, Yutaka Yasuda

Saganoseki Smelter, one of the largest copper producers in Japan, currently operates a single flash smelting furnace to produce 450,000 tons of new copper annually. The smelter used to employ two flash furnaces, and integrated the two into one in 1996. Since then, various improvements to its facilities and technologies have been made to increase productivity. To upgrade the operation efficiency, "stability" was considered a key issue, and the measures were taken to increase the operation and facility reliability. Currently, the furnace is running at a feed rate of 215 DMT/h, while the furnace utilization has been maintained at 97%. This paper outlines recent improvements that have made to increase furnace productivity and efficiency.

Jan 1, 2014

An old philosopher once said, "God grant me the serenity to accept those things I cannot change, the courage to change those which I can, and the wisdom to know the difference." It is time to take stock of how the human race has progressed-whether the trend now points toward greater evils or finer things. It is time that we stop fooling ourselves and put into effect a program of "real" conservation. By this it is not meant that we limit our concept to planting new forests, preserving wild life or preventing soil erosion, but rather taking stock of the expectancy of our resources, expanding human resourcefulness and effecting careful utilization and replacing of, or producing substitutes for, material resources. Man is still dependent upon energy and matter in certain usable forms, despite the fact that energy is inherent in all matter. Until such progress is made that the energy contained in all matter can be controlled, man must continue to utilize the common fuels. Advancement of research in atomic energy has cast a gleam of hope for future use of the tremendous energy contained in the atom. Use of atomic power for industrial pursuits would open up limitless resources of power. This energy, of course, is a two-edged sword, since man's progress and his means of destruction have always evolved parallel to each other. Thus it is estab-

Jan 1, 1950

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By Benoît Pinier, Jason Furtney, Gustavo Sampaio Lopes, Jorge Valencia, Johan Hawinkel

This paper describes a numerical modeling study on the effect of airdecking on vibrations, fragmentation, and movement in mining-related rock blasting. Practice has shown that air gaps reduce blast vibrations and damage while maintaining the required fragmentation and movement, yielding similar blast outcomes with less explosive mass per hole. Given that the premise of “replacing explosives with air” for better blast results is counterintuitive, this paper aims to shed light on the physical mechanisms and processes occurring in a blast with airdecks. It is hypothesized that airdecks are effective and beneficial because they load the rock at pressures lower than what is required to crush the rock. In the airdeck, the explosive gasses directly fracture rock and avoid energy loss due to crushing. In essence, the airgap allows similar outcomes in fragmentation and throw with less total explosive product, as the lower pressure gasses in the airdeck are still effective at breaking and moving the rock. This is distinct from only having less explosive and more stemming, as the stemming reduces the pressure more than an airdeck at the same position. This study uses the blastFoam software (for modeling of single and multiphase flows) to accurately calculate the pressure history throughout a blasthole and air gap. The pressure and gas loading are coupled to numerical models of vibration, fragmentation, and blast movement. Using this modeling technique, a suite of blast scenarios for typical configurations in a range of commodities is assessed with and without airdecks. Rock blasting practitioners have a responsibility to protect communities, infrastructure, and heritage — demystifying airdecks through a better understanding of the physics provides another tool in the blasting engineering toolkit to serve this goal.

Jan 21, 2025

By John Floyd, Larry Wardrip

A series of tests were conducted to evaluate the performance of a high density, high velocity cartridged explosive. The tests included two production blasts in a limestone quarry and two production blasts in a granite quarry. To quantify blast and product performance, each blast was monitored with the following equipment: l Two (16mm (Lo Cam) high speed cameras (500 images per second) l Velocity of detonation recorder (I million samples per second) l Four face motion accelerometers (1 million samples per second) l Digital seismograph The fragmentation distribution produced by each blast was quantified with digital image analysis The benefits of the use of high velocity, high density toe loading was quantified in terms of: l Vibration reduction l Fragmentation improvement l Excavator performance In addition to the field tests, a comprehensive evaluation was performed to determine the cost/benefit relationship of the use of the toe load. This paper will include the findings of the study along with guidelines for use in other quarry operations.

Jan 1, 2002

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By Khiva Haidar Shauma Tassno, Zulham Ahmad, Farhan Harist Maharesi, Abdullah Badawi Batubara

Blasting operations can use a bulk emulsion explosive (EE) with a formulation based on used oil as a replacement for refined fuel oil. The most commonly employed used oil for making EE is a mineral based used engine oil that passes an impurity content standard. It is known that not all types of used oil are easily incorporated into EE formulations. Impurities in used oil can disturb EE stability resulting in crystallization and phase separation and consequently led to poor detonation quality. In 2024, a poor blast result occurred at an Indonesian mine due to utilization of used oil that was not within specification. A research project conducted from February to April 2025 found that used transmission oil differs from used engine oil in hydrocarbon composition. Transmission oil contains more additives that affect EE stability due to polarity differences and the disruption of colloidal state stability. Lab tests including stress testing and crystal growth observation aided the development of a stable EE formulation based on used oil and used transmission oil. In mid-April 2025, blast evaluations were conducted using the EE that was formulated using used engine oil and used transmission oil. Measurements of velocity of detonation, fragmentation, and digging time, demonstrated high quality EE was produced. Application of used oil in EE revolutionized the capability of mining operations to improve blast sustainability and cleanliness. Through comprehensive research, robust testing, and effective supply chain management, it is possible to replace some portion of refined fuel oil with used oil without compromising blasting performance. The inclusion of used transmission oil broadens the overall used oil specification and increases the volume of recycled used oil available for blasting. The increased volume of used oil available can reduce the amount of waste generated by mining projects while maintaining operational efficiency.

Jan 26, 2026