Search Documents

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By John Crawford

MUCH has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of -48-mesh material. The percentage of this -48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The ton-nage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reason-able cleaning job down to and including +100 mesh, by far the greater-majority stop at or short of the +48-mesh size.

Jan 1, 1935

By Oliver Bowles

ROCK is no doubt the most abundant of all material things because the planet on which we live is made of it. All animal and vegetable organisms and the multitude of natural and manufactured products that occupy a comparatively insignificant film on the outer surface of the planet are derived from rock. Processes of Nature acting for untold centuries have transformed rock into soil, making possible the development of vegetable and annual life; and rocks have supplied the numerous raw materials, metallic and nonmetallic, wherewith the innumerable appurtenances of a complex civilization have been fabricated. As time goes on we live with increasing speed and with enlarged desires. Time and space are shortened by man's ingenuity, and products for human use must be manufactured with greater and greater celerity. It was inevitable that Nature's slow processes of rock alteration should fail to keep pace with human demands and that the variety of natural products should fall far short of the requirements of an industrial age. Man therefore supplemented these processes by attacking rock in its native bed amid using it to supply needs not otherwise satisfied.

Jan 1, 1934

Importance of Strain to Fragment Strength in Blasting Induced Pre-Conditioning When a rock is blasted, cracks propagate through the rock causing the rock to fracture. This paper focuses on applying the results from a series of small scale blasting tests were designed to show the effect that varying blast variables such as explosive type and explosive energy have on the resulting strength of the post blast fragments. It was shown that the velocity of detonation of the explosive product affects the reduction of fragment strength. This has important implications for the downstream comminution process. The observations from these tests are then explained with reference to the principles of fracture mechanics. A simple but effective prediction of blast induced preconditioning is shown.

Sep 13, 2010

By Earl F. Mathers

Few people would question that coal is king in the Campbell County, WY area. Other industries, such as oil production and ranching, also contribute significantly to the economic base, but coal mining and related industry development dominate. In recent years, Gillette has become the commercial hub of northeastern Wyoming. This development has been largely a response to the growth of the coal industry in Campbell County. Historically, Campbell County developed as a ranching area, a process that was aided by the passage of rail lines through the area, allowing early ranching interests to get their livestock to market. For decades, the Gillette-Campbell County area was predominantly a ranching area that experienced only incremental population growth.

Jan 1, 1994

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By J. Severin

Surface mining operations are increasingly involving the design and development of deeper and larger open pits, often with plans to transition into underground mass mining operations. Experiences at the Palabora Mine in South Africa demonstrate the complex interactions between underground workings and the steep slopes above that may lead to slope movements that potentially pose safety and economic concerns. To properly assess the rock mass response to these interactions for planning of future developments, understanding the controlling influence of geological and geomechanical structures is crucial. Preliminary results are presented from a detailed review of historical slope monitoring data from the Palabora Mine, before and after the initiation of block caving 400-m beneath a 800-m deep pit. This paper demonstrates that a detailed analysis of geology and monitoring data can be used to better understand the kinematic controls of complex rock slope displacements and interactions between open pits and underground mines. This investigative treatment of the monitoring data is important in understanding the failure mechanisms prior to undertaking sophisticated 3-D numerical models.

May 1, 2009

By Henry Branes

Para maximizar el retorno de la inversión se aplica la economía de escala pero no se consideran el riesgo financiero al aumentar la escala del proyecto. Las curvas de recuperación metalúrgica vs ley de minera no son lineales. Esto implica elegir un punto óptimo, donde los rendimientos decrecientes de la minería selectiva no justifican el aumento del costo de minado y la reducción de la tasa de alimentación a planta. El artículo analiza las variables más significativas y propone una metodología para definir la capacidad de planta óptima para obtener el máximo rendimiento de la inversión basado en la sensibilidad de una serie de escenarios de planes de minado.

Sep 1, 2017

By Elard Miranda, Carlos Lopez

El éxito extractivo en el tratamiento de los minerales auríferos, depende fundamentalmente de su buena caracterización física y metalúrgica, de modo que para un determinado grado de liberación del mineral brinde información acerca de tamaño del elemento valioso y si este se encuentra liberado o incluido en alguna especie mineralógica; del mismo modo debe conocerse el tipo de elemento valioso, si es oro o electrum y los porcentajes de Plata que presenta este último.

Sep 1, 2017

By K. Hakalehto

El uso de métodos modernos en el uso de chimeneas de las minas en Finlandia permite obtener un mejor desarrollo racionalizado de la mecanizado. En ese sentido, el presente texto señala dos métodos seguros y rápidos para la perforación de chimeneas. La perforación para estas chimeneas se desarrolló en rocas duras duras y fuertes en 1972. Asimismo, el costo, itinerario y velocidad son factores a considerar en el empleo de métodos para perforación de chimeneas.

Jan 1, 1982

By Carlos Virrueta

"El presente texto señala la importancia del comportamiento seguro en el sistema de riesgos aplicados al comportamiento de los trabajadores, salud y medio ambiente para así establecer los lineamientos yresponsabilidades requeridos para realizar el programa de Auditorías de Comportamiento Seguro, fortalecer el compromiso visible de liderazgo de los equipos de trabajo, así como crear y fortalecer en las personas el hábito de la prevención de los riesgos."

Oct 21, 2015

By Jorge Barrios, Gina Pachao

El presente trabajo da a conocer la importancia de la implementación del sistema de caracterización de estructuras en taludes y zonas inaccesibles en mina a tajo abierto, mediante el levantamiento remoto semiautomático que incluye fotogrametría (uso de cámaras de alta definición) y escáner laser 3D, que consiste en el escaneo de la superficie con la generación de nube de puntos espaciales y obtener una superficie digital en 3 dimensiones, que luego será analizada, digitalizada y la obtención de datos estructurales tales como ubicación, orientación (DipDirection / rumbo y buzamiento), espaciamiento, potencia y persistencia).

Sep 29, 2023

By Jorge Alencastre Miranda

El presente artículo es un análisis dinámico estructural de una faja transportadora, (tipo Staker Radial) de una empresa minera a través de modelos conceptuales simplificados y programas computacionales.

Apr 1, 2016

By Federico Ma. Aspíllaga

El presente estudio señala la importancia del control radiográfico que el Departamento de Seguridad e Higiene Industrial realizó al personal de Cerro de Pasco. La empresa -a través de este método de control- conoce el porcentaje de salud y enfermedad de sus servidores. El diagnóstico de las enfermedades neumoconiosis y silicosis deben ser evaluadas por un médico especialista en enfermedad ocupacionales. Asimismo, una vez diagnosticada la enfermedad se busca el control adecuado de la enfermedad, la profilaxis, y se refuerza las medidas de prevención tanto en el ambiente de trabajo como en el trabajador mismo.

Aug 20, 1965

By Oscar Silva C.

El presente trabajo señala la importancia del proceso de entrenamiento como parte de las funciones de supervisión. Por tal motivo, se describen cuáles son las cinco necesidades básicas del supervisor, el concepto de entrenamiento de la industria, cuándo se debe entrenar, el planeamiento del entrenamiento, las relaciones humanas y el entrenamiento. Una vez descrito el funcionamiento del supervisor, se obtendrán ventajas como el convertirse en un ejemplo para su personal, se disminuye la tensión del trabajo y se permitirá todo el tiempo necesario para el estudio y aplicación de técnicas, habilidades, capacitándose de esa manera para ser promovido.

Aug 20, 1963

By Alejandre Monge Gordillo

La siguiente investigación describe las generalidades de la administración de grandes empresas como principios alternativos y más seguros que los métodos del empirismo. En este punto, se revisan nuevas perspectivas sobre la economía de empresas, los aportes de Frederick W. Taylor y sus medidas de administración científica, los principios generales del establecimiento industrial, los conceptos de la concentración del esfuerzo en un campo limitado de actividad, los principios sobre el costo productivo, el significado económico de la "standarización" y las etapas del desarrollo de una empresa por F. W. Taylor. Concluyendo que la aplicación del método científico es factible en una operación industria,l dado que aprovecha exactamente los resultados de otras operaciones y retoma el conocimiento de otras áreas para organizar adecuadamente una empresa.

Jul 20, 1955

By W. O. Macha

El presente texto señala la importancia del Sink and Float como método de concentración que facilita la explotación de minas de bajas leyes anteriormente desapercibidas en la industria minera. El estudio se divide en dos partes: la primera describe las generalidades de dicho método, mientras que la segunda muestra las pruebas metalúrgicas desarrollas con minerales de las minas "Casapalea", "San Cristóbal" , "Yauricocha" y "Tajo Abierto" de la Cerro de Paseo Co., así como las de "Austria Duvaz" "Victoria" y "Germania"de la "Negociación Minera y Metalúrgica Lizandro Proaño S . A . ", y la de "Sacracancha Gale". Como consecuencia de estas pruebas de Heavy Media, se encontró que el 75% de minerales tiene posibilidades de ser pre-concentrados por este método, asimismo la importancia del Sink and Float radica en el campo de los minerales usados corno relleno en las minas y de las abandonadas canchas.

Jul 20, 1960

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013