Search Documents

By Reed S. C. Rogers

There is recent evidence that high frequency screening can be a viable alternative to hydrocyclone classification for a wide variety of grinding applications. However, since high frequency screening is a relatively new development, the decision to use screens generally must be based on full scale screening tests of a slurry material of interest. In this paper the authors employ mathematical simulation models as an aid to evaluating the use of screens versus hydrocyclones for closed circuit fine grinding. This approach is validated in a pilot plant study and then demonstrated for the design of full-scale grinding circuit, including classifier cost comparisons. For the case of maximum production rates versus product size, without a constraint on fine product solids densities, results indicate that screening with Derrick sandwich type cloths can give higher grinding circuit production rates with more narrowly sized products than when hydrocyclones are used. These results are explained in terms of the bypass and Sharpness Index of the respective classifier partition curves. Classifier cost comparisons for the full scale circuit show that although the installed cost of screens is substantially higher than equivalent capacity hydrocylone operations, even modest increases in circuit capacity caused by screens; can significantly reduce total grinding costs.

Jan 1, 1985

By Y. Makola, M. Kilumba, S. Mwaba, P. Ilunga, F. Banze, B. Nel, P. Kyoni, N. Mautsa, R. Nkomba, G. Ilu

Kamoto Copper Company is a copper cobalt mining company established in Lualaba Province of Democratic Republic of Congo under a Joint Venture between Glencore PLC and Gecamines (the state-owned mining company). Operations consist of underground and open pit mines, a concentrator producing sulfide concentrate and oxide ores milled slurry, and a hydrometallurgy plant producing copper cathode and cobalt hydroxides from concentrate and ores. The production capacity is 300 k/a of copper cathode and 35 kt/a of cobalt hydroxide. Since Q4 2020, the Luilu hydrometallurgy plant has experienced operational instabilities due to increase in proportion of dolomite in the ore mined and fed to the plant. This was diagnosed by the significant increase in calcium grade in ore and acid consumption, continuous foaming, and overflow of tanks with subsequent adverse impact on equipment availability due to corrosion caused by acidic spills, structure integrity, and safety concerns around the acidic slurry spills. Production was adversely impact due above equipment availability and often throughput restriction to mitigate the foaming and overflows. A high gangue-acid-consuming ore management programme was developed with the aim of mitigating these impacts. The programme included: (i) use of defoamer agent in leach to stop foaming and overflow, (ii) design of a mechanical solution to leach foaming and overflow, and (iii) froth flotation for copper and cobalt minerals separation from dolomite. Only option (i) is presented in this paper. Through laboratory testwork, pilot-plant testing, plant trial, and full plant implementation, Kamoto Copper successfully implemented a defoamer agent (Kemfoam X9980) dosing at leach, resulting in significant reduction in foaming and overflow of leach reactors and countercurrent decantation thickeners. The optimum defoamer dose rate obtained was 20 mg/L. Since then, the Luilu recovered its operational stability, the corrosion of critical equipment ceased, and availability improved as the acidic leach slurry spills ceased. The constraint on throughput due to leach foaming was addressed and the frequency of sliming events in the thickeners was significantly reduced as the foaming on the supernatant surface ceased, with subsequent significant reduction in interfacial crud in solvent extraction.

Jan 1, 2023

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

The Broken Hill orebody ,occurs in the Willyama Complex, a block of Precambrian rocks which have been strongly folded and metamorphosed at moderate to high grade. Although -the origin of the silver-lead-zinc mineralization remains obscure, recent investigations have substantiated the view that the orebody has undergone concomitant high grade metamorphism with the enclosing wallrocks. The mesoscopic structures produced by this metamorphism are described, and the possible processes Telating to their formation are disoussed.In the high grade ore, metamorphic structures which can be recognized are foliation and lineation, wallrock fragments, layering, flow folds, ore breccias, and sulphide bearing veins. These structures can be related to processes involving plastic flow and fluid phase transport of the mineral assemblage. 'In areas of low grade mineralization adjacent to high grade ore, the structures more closely resemble those produced in -the wallrocks-foliatlon, lineation, layering, folds, and sulphide injections. Within areas of high grade ore, lenses and pods of manganese silicates Probably represent original inhomogeneities in the ore, i.e., portions of manganese-rich and sulphide deficient rock which have been metamorphosed to manganese silicates.From the structures displayed, a sequence of events has been established for the plastic flow of ore during deformation.

Jan 1, 1975

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By P. F. Ahner, Leonidas Petrakis, Fred E. Kiviat

High gradient magnetic separations (HGMS) is a recently developed technique in which magnetic micron-size particles contained in a flowing fluid medium can be extracted from that medium. HGMS is presently utilized on a commercial scale in the kaolin processing and steel industries, and is being investigated for solid-liquid separations in numerous other processes. The performance characteristics of HGMS in the kaolin and steel industries are briefly summarized. A discussion of HGMS performance with respect to solids removal in a coal liquefaction process is presented to illustrate its applicability to difficult solid-liquid separations. Here, the properties of the solids suspended in the liquified coal are such that the HGMS separator achieves over 90% solids removal. The optimization of the HGMS operating parameters to yield these results will be discussed. To further illustrate the potential of HGMS, its performance with respect to the removal of oil and solids (over 98% removal) from a petroleum refinery process water effluent stream will be briefly considered.

Jan 1, 1980

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By John Ross Middleton

Based upon 30 years+ experience in the Development, Implementation and Ongoing Support of Computer based Melt Shop Management Systems in about 40 plants in the UK, Europe and the USA, consideration of the overall facilities of a state of the art, comprehensive, Integrated Melt Shop System covering Melting and Secondary processes for all grades of steels and superalloys; the scope of functionality of these systems, covering Raw Materials and Consumables Procurement and Inventory Management, Laboratory Management, Melt Shop Scheduling, Furnace Charge and Additions Optimisation, Level 1.5 to Level 2.5 Materials Optimisation and Process Control Calculations, Process Data Recording, Management of Ladles, Furnace Bodies, Vessels and Moulds, Comprehensive Management Reporting and Integration with Corporate ERP Systems. The second section of the paper reviews the key ‘Success Factors’ to achieve rapid, successful implementation, comprehensive, fast response user support, continuing system improvement and maintaining ‘perfect fit’ of system to operations in an ever changing future technical, operations and business environment.

Jul 29, 2018

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By J. Iannicelli

Availability of large-scale high field/high gradient magnetic separators during the past five years allows applications of magnetic separation to feebly paramagnetic materials which have been considered nonmagnetic in the past. Technology is now available for magnetically attracting not only feebly magnetic compounds of iron such as hematite and pyrite, but also hundreds of compounds of nonferromagnetic elements such as copper, tin, uranium, vanadium. Besides enabling novel separation of industrial minerals, metallic ores, and coal, the new technology also can be used in effluent treatment, catalyst cleanup, and purification of chemicals.

Jan 1, 1979

By J. A. Bartnik

In recent years, the need has become more and more accute for a high capacity, high intensity, wet magnetic separator for the concentration of finely ground, paramagnetic minerals. As a result of this increased interest, extensive test work has been conducted at our Central Test Laboratory, and the basic design for such a separator has been established. Three units have been developed to comprise a full line of this equipment: (a) Series 4L (laboratory), Figure I, is manually operated to permit maximum flexibility and precise control of each variable, with a capacity of 4 gallons per minute. (b) Series LOCC, Figure II, functions by automatically controlled feeding and washing cycles, and has a capacity of approximately 1.0 tons per hour. (c) Series 200CF, Figure III, basically consists of an annular pole box, rotating through the high intensity magnetic field. This unit has a capacity of approximately 20 tons per hour.

Jan 1, 1966

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. In 1996, however, it successfully shifted to a single furnace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. [n 1996, however, it successfully shifted to a single fumace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This ' paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

HIGH LAKE PROPERTY --HISTORYHISTORY -19501950??s ??Kennarctic Exploration discovers Exploration sulphides (A/B & (D Zones) at High Lake during helicopter reconnaissance exploration program.- -1991 93 Aber signs agreement to earn in to the High Lake Property from Kennecott. 63 holes drilled, primarily testing the known deposits. -2001 Wolfden purchases 100% interest in High Lake from Kennecott and Aber -2002 Wolfden performs helicopter borne TEM Survey over the High Lake Greenstone Belt. -2003 West Zone was discovered following UTEM & Gravity Surveys (performed by Teck Cominco ) over an airborne anomaly approx. 1km west of the known deposits. -2004 Wolfden awarded Bill Dennis Prospector of the Year

May 1, 2006

By Gary B. Hemphill

Each year the demand for precision blasting increases due to the reduction in the amount of prime land. More site preparation and hone building requires blasting than they did a decade ago, Because of this increased need for blasting in more populated areas, the need for blasters and engineers knowledgeable in work involving blasting nets has increased.

Jan 1, 1978